• 한국전기전자재료학회논문지
• /
• 제33권4호
• /
• pp.263-270
• /
• 2020

In this study, the physical mechanism and diffusion effects in aluminium implanted silicon was investigated. For fabricating power semiconductor devices, an aluminum implantation can be used as an emitter and a long drift region in a power diode, transistor, and thyristor. Thermal treatment with O₂ gas exhibited to a remarkably deeper profile than inert gas with N₂ in the depth of junction structure. The redistribution of aluminum implanted through via thermal annealing exhibited oxidation-enhanced diffusion in comparison with inert gas atmosphere. To investigate doping distribution for implantation and diffusion experiments, spreading resistance and secondary ion mass spectrometer tools were used for the measurements. For the deep-junction structure of these experiments, aluminum implantation and diffusion exhibited a junction depth around 20 ㎛ for the fabrication of power silicon devices.

• 한국기계기술학회지
• /
• 제13권4호
• /
• pp.93-99
• /
• 2011

This paper presents a new type of optical silicon accelerometer using deep reactive ion etching (DRIE) and micro-stereolithography technology. Optical silicon accelerometer is based on a mass suspended by four vertical beams. A vertical shutter at the end of the mass can only moves along the sensing axis in the optical path between two single-mode optical fibers. The shutter modulates intensity of light from a laser diode reaching a photo detector. With the DRIE technique for (100) silicon, it is possible to etch a vertical shutter and beam. This ensures low sensitivity to accelerations that are not along the sensing axis. The microstructure for sensor packaging and optical fiber fixing was fabricated using micro stereolithography technology. Designed sensors are two types and each resonant frequency is about 15 kHz and 5 kHz.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.67-68
• /
• 2008

In this study we have developed a packaged silicon carbide power diode with blocking voltage of 2kV. PiN diodes with 7 field limiting rings (FLRs) as an edge termination were fabricated on a 4H-SiC wafer with $30{\mu}m$-thick n-epilayer with donor concentration of $1.6\times10^{15}cm^{-3}$. From packaged PiN diode testing, we obtained reverse blocking voltage of 2kV, forward voltage drop of 4.35V at 100A/$cm^2$, on-resistance of $6.6m{\Omega}cm^2$, and about 8 nanosec reverse recovery time. These properties give a potential for the power system application.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.377-377
• /
• 2007

A simplified integration process including packaging is presented, which enables the realization of the portable fluorescence detection system. A fluorescence detection microchip system consisting of an integrated PIN photodiode, an organic light emitting diode (OLED) as the light source, an interference filter, and a microchannel was developed. The on-chip fluorescence detector fabricated by poly(dimethylsiloxane) (PDMS)-based packaging had thin-film structure. A silicon-based integrated PIN photo diode combined with an optical filter removed the background noise, which was produced by an excitation source, on the same substrate. The active area of the finger-type PIN photo diode was extended to obtain a higher detection sensitivity of fluorescence. The sensitivity and the limit of detection (LOD S/N = 3) of the system were $0.198\;nA/{\mu}M$ and $10\;{\mu}M$, respectively.

• 한국통신학회논문지
• /
• 제37권4A호
• /
• pp.219-226
• /
• 2012

본 연구는 조명 및 무선통신이 동시에 가능한 가시광 송수신기에 대해 가시광 통신 본연의 가시성, 무선 통신의 사용 편의성 그리고 고속의 통신 속도를 고려해 edge-emitting laser diode와 silicon photo diode를 기반으로한 고속 가시광 무선 송수신기를 구현하였다. 제안된 가시광 무선 송수신기는 120Mbit/s의 고속에서 양방향 전송이 가능하도록 설계되었으며 이때 발생하는 누화(crosstalk)를 방지하기 위한 방법으로 shielding 방식을 적용해 가시광 송수신기의 성능을 실험적으로 측정 분석하였다. 또 수신기의 시야각 확대를 위한 방법으로는 새로운 구조의 광학적 antenna를 적용해 광학적 antenna가 없는 두 개의 송수신기 사이의 전송링크 특성과 광학적 antenna를 사용한 두 개의 송수신기 사이의 전송링크 특성을 2차원 평면상에서 전송거리, 적용범위 그리고 기울임 정도를 변화시켜 실험과 시뮬레이션을 통해 그 성능을 비교 분석하였다.

• Journal of Radiation Protection and Research
• /
• 제25권4호
• /
• pp.197-205
• /
• 2000

실리콘 PIN 다이오드 검출기를 이용하여 전자선량계(PED)를 설계 및 제작하고, 전자신호회로의 성능과 방사선 검출 반응특성을 평가하였다. 전자회로의 성능검사에서는 방사선에 의한 검출기의 신호가 신호처리회로에서 양호하게 출력되었으며, $^{137}Cs$ 감마 방사선을 이용한 방사선조사 시험결과 선량계의 반응도 및 분산계수는 각각 1.85 cps/$Gy{\cdot}h^{-1}$ 및 19.3%로 측정되어 전자선량제의 성능기준을 만족하는 것으로 나타났다. 본 전자선량계의 시작품은 향후 전자회로의 성능향상과 작동 프로그램을 보완 및 개선함으로써 개인 방사선 모니터링에 활용될 것으로 기대된다.

• 한국전기전자재료학회논문지
• /
• 제31권4호
• /
• pp.203-207
• /
• 2018

In this work, we investigate the effects of lithium doping on the electric performance of solution-processed n-type zinc tin oxide (ZTO)/p-type silicon carbide (SiC) heterojunction diode structures. The proper amount of lithium doping not only affects the carrier concentration and interface quality but also influences the temperature sensitivity of the series resistance and activation energy. We confirmed that the device characteristics vary with lithium doping at concentrations of 0, 10, and 20 wt%. In particular, the highest rectification ratio of $1.89{\times}107$ and the lowest trap density of $4.829{\times}1,022cm^{-2}$ were observed at 20 wt% of lithium doping. Devices at this doping level showed the best characteristics. As the temperature was increased, the series resistance value decreased. Additionally, the activation energy was observed to change with respect to the component acting on the trap. We have demonstrated that lithium doping is an effective way to obtain a higher performance ZTO-based diode.

• Transactions on Electrical and Electronic Materials
• /
• 제18권4호
• /
• pp.199-202
• /
• 2017

Silicon carbide (SiC) is being spotlighted as a next-generation power semiconductor material owing to the characteristic limitations of the existing silicon materials. SiC has a wider band gap, higher breakdown voltage, higher thermal conductivity, and higher saturation electron mobility than those of Si. When using this material to implement Schottky barrier diode (SBD) devices, SBD-state operation loss and switching loss can be greatly reduced as compared to that of traditional Si. However, actual SiC SBDs exhibit a lower dielectric breakdown voltage than the theoretical breakdown voltage that causes the electric field concentration, a phenomenon that occurs on the edge of the contact surface as in conventional power semiconductor devices. Therefore in order to obtain a high breakdown voltage, it is necessary to distribute the electric field concentration using the edge termination structure. In this paper, we designed an edge termination structure using a field plate structure through oxide etch angle control, and optimized the structure to obtain a high breakdown voltage. We designed the edge termination structure for a 650 V breakdown voltage using Sentaurus Workbench provided by IDEC. We conducted field plate experiments. under the following conditions: $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $75^{\circ}$. The experimental results indicated that the oxide etch angle was $45^{\circ}$ when the breakdown voltage characteristics of the SiC SBD were optimized and a breakdown voltage of 681 V was obtained.

• Journal of the Optical Society of Korea
• /
• 제18권5호
• /
• pp.569-573
• /
• 2014

We demonstrate a low-cost, superbly efficient way of etching for the nano-, and micro-sized pyramid patterns on (100)-oriented Si wafer surfaces for use as a patterned master. We show a way of producing functional optical films for the viewing angle direction brightness-enhancement of Lambertian LED (light emitting diode)/OLED (organic light emitting diode) planar lighting applications. An optimally formulated KOH (Potassium hydroxide) wet etching process enabled random-positioned, and random size-distributed (within a certain size range) pyramid patterns to be developed over the entire (100) silicon wafer substrates up to 8" and a simple replication process of master patterns onto the PC (poly-carbonate) and PMMA (poly-methyl methacrylate) films were performed. Haze ratio values were measured for several film samples exhibiting excellent values over 90% suitable for LED/OLED lighting purposes. Brightness was also improved by 13~14% toward the viewing angle direction. Computational simulations using LightTools$^{TM}$ were also carried out and turned out to be in strong agreement with experimental data. Finally, we could check the feasibility of fabricating low-cost, large area, high performance optical films for commercialization.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1994년도 제3회 학술강연회논문집
• /
• pp.21-26
• /
• 1994

Conventional electroexplosive devices (EED) commonly use a very small metal bridgewire to ignite explosive materials i.e. pyrotechnics, primary and secondary explosives. The use of semiconductor devices to replace “hot-wire” resistance heating elements in automotive safety systems pyrotechnic devices has been under development for several years. In a typical 1 amp/1 watt electroexplosive devices, ignition takes place a few milliseconds after a current pulse of at least 25 mJ is applied to the bridgewire. In contrast, as for a SCB devices, ignition takes place in a few tens of microseconds and only require approximately one-tenth the input energy of a conventional electroexplosive devices. Typically, when SCB device is driven by a short (20 $\mu\textrm{s}$), low energy pulse (less than 5 mJ), the SCB produces a hot plasma that ignites explosive materials. The advantages and disadvantages of this technology are strongly dependent upon the particular technology selected. To date, three distinct technologies have evolved, each of which utilizes a hot, silicon plasma as the pyrotechnic initiation element. These technologies are 1.) Heavily doped silicon as the resistive heating initiation mechanism, 2.) Tungsten enhanced silicon which utilizes a chemically vapor deposited layer of tungsten as the initiation element, and 3.) a junction diode, fabricated with standard CMOS processes, which creates the initial thermal environment by avalanche breakdown of the diode. This paper describes the three technologies, discusses the advantages and disadvantages of each as they apply to electroexplosive devises, and recommends a methodology for selection of the best device for a particular system environment. The important parameters in this analysis are: All-Fire energy, All-Fire voltage, response time, ease of integration with other semiconductor devices, cost (overall system cost), and reliability. The potential for significant cost savings by integrating several safety functions into the initiator makes this technology worthy of attention by the safety system designer.