• Korean Journal of Materials Research
• /
• v.27 no.1
• /
• pp.12-18
• /
• 2017

Transparent organic-inorganic hybrid hard coating films were prepared by the addition of $SiO_2$ or $ZrO_2$, as an inorganic filler to improve the hardness property, filler was highly dispersed in the acrylic resin. To improve the compatibility in the acrylic resin, $SiO_2$ or $ZrO_2$ is surface-modified using various silanes with variation of the modification time and silane content. Depending on the content and kind of the modified inorganic oxide, transparent modified inorganic sols were formulated in acryl resin. Then, the sols were bar coated and cured on PET films to investigate the optical and mechanical properties. The optimized film, which has a modified $ZrO_2$ content of 4 wt% markedly improved in terms of the hardness, haze, and transparency as compared to neat acrylate resin and acrylate resin containing modified $SiO_2$ content of 8 wt%. Meanwhile, the low transparency and high haze of these films slowly appeared at $SiO_2$ content above 10 wt% and $ZrO_2$ content of 5 wt%, but the hardness values were maintained at 2H and 3H, respectively, in comparison with the HB of neat acrylate resin.

• Textile Coloration and Finishing
• /
• v.25 no.3
• /
• pp.172-180
• /
• 2013

Aramid fibers are being used increasingly in a wide range of application due to low density, high specific strength, high modulus, and high thermal resistance. But owing to its special physical and chemical structures, it is sensitive to absorb the ultraviolet light which will degrade the fiber's useful mechanical properties and structure. In this paper, the sol-gel technique was used to improve the photo-stability of p-aramid fibers. $TiO_2$, modified $SiO_2$/$TiO_2$ sol were used as coating solutions. The influence of the such coatings on the photo-stability of p-aramid fiber was investigated by an accelerated photo-ageing method using xenon lamp. The photo-stability of p-aramid fiber showed obvious improvement after the modified silica binding coating. But the amorphous $TiO_2$ sol coatings showed a negative effect. After 144h light exposure, the modified silane binder-coated fibers showed less degradation in mechanical properties with the retained tensile strength greater than about 70% of the original value.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.102-105
• /
• 2005

Photoinitiated polymeric dental restorative nanocomposites (PDRNC) were designed to be useful for the variety of dental restoration. Hybrid-filler composed of barium silicate (avg. dia.:1 ${\mu}m$) and nano-sized silica (avg. dia: 40 and 7 nm) was adopted as a filler system. To improve the interfacial behavior with the resin matrix of bisphenol A glycerolate methacrylate/triethyleneglycol dimethacrylate (60/40 wt%), the surface of the filler was hydrophobically treated with a silane coupling agent. A visible light system of camphorquinone photo-initiator and 2-(dimethylamino)ethyl methacrylate photo-accelerator was utilized to activate the PDRNC. Esthetic properties of PDRNC was investigated by measuring the Hunter L, a, b values and it was discovered that PDRNC produced in this work showed excellent esthetic properties with an increase in 7 nm nanofiller content.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.3
• /
• pp.157-170
• /
• 2002

The purpose of this study is to analyze the shear bond strength according to kinds of surface treatment agents and resin cements after acid etching of IPS Empress 2. For this purpose, test groups were classified into silane-treated bonding groups, silica-coated group and Targis link applied group. Then, nine bonding groups in total, each three groups per kind, were prepared by using three kinds of resin cements-Panavia F, Variolink II and Rely-X ARC, and thirty test specimens per group were prepared. To examine any changes in the oral environment, the shear bond strength of each test specimen was measured after dipping test for 24 hours and for five weeks, respectively, in distilled water at $37^{\circ}C$ and performing heat cycle 10,000 times in total, each 2,000 times per week, during a five weeks of dipping, under the condition similar to the oral environment. The bond failure modes were also observed by means of a scanning electron microscope. The results are summarized as follows 1. Statically significant differences between the surface conditioning materials were observed. The shear strength of the silane treatment was the highest of all three types of surface treatments(p<0.001). 2. Shear strengths varied significantly for different types of resin luting agents. But bond strength of Targis link surface treatments were not significantly different(p<0.05). 3. No significant difference of bonding strengths was found between storage time conditions(24 hours and 5 weeks). Only group II, IV, VII, IX were significantly different(p<0.05). 4. After thermocycling, the shear bond strengths of all groups were significantly decreased (p<0.05). Group III, V, VI were no significantly different. 5. On the SEM observation of fractured surfaces, all groups were shown complex failure.

• Clinical and Experimental Reproductive Medicine
• /
• v.27 no.4
• /
• pp.339-344
• /
• 2000

Objective: To evaluate silane-coated silica particles (Sil-select) as an alternative to polyvinylpyrrolidone-coated particles (Percoll) for gradient separation of spermatozoa, for use in assisted reproduction. Methods: 20 normal semen based on WHO criteria were included in this study. Recovery of motile and morphologically normal spermatozoa after using two-layer Percoll and Sil-select gradient respectively was recorded. Motility, HOST (hypoosmotic swelling test) and the detection of malondialdehyde for LPO (lipid peroxidation) after 24 h of incubation at $37^{\circ}C$ in a 5% $CO_2$ incubator were compared. Results: Percoll (78.5%) and Sil-select (79.1%) showed a significant increase in the motility compared to ejaculate (60.9%) but no difference between Percoll and Sil-select. Normal sperm morphology significantly increased after Percoll (57.6%) and Sil-select (53.7%) compared to ejaculate (35.8%) but no difference between Percoll and Sil-select. No differences in the recovery of motile spermatozoa and motility, HOST and the production of malondialdehyde after 24 h incubation were found when comparing the use of Percoll and Sil-select. Conclusion: Sil-select seems to be an attractive alternative to Percoll for sperm separation in assisted reproduction.