• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.366-375
• /
• 2008

Generally a return current plane(RCP) of high speed digital and analog part is partitioned. This is achieved in order to decrease the noise interference between subsystem in PCBs(Printed Circuit Boards). However, when the connected signal line exists between each sub system, this partition will cause unwanted effects. In a circuital point of view, RCP partition has a bad influence upon signal integrity. In a EMI(Electromagnetic Interference) point of view, the partition of the return current plane becomes a primary factor to increase the radiated emission. Component bridge(CB) is usecl for the way of maintaining signal integrity, still specific user's guide doesn't give sufficient principle. In a view point of signal integrity, design principle of multi-CB using method will be analyzed by measurement and simulation. And design principle of noise mitigation will be provided. Generally interval of CB is ${\lambda}/20$ ferrite bead. In this study. When multi-CB connection is applied, design principle of ferrite bead and chip resistor is proved by measurement and simulation. Multi-connected chip resistance$(0{\Omega})$ is proved to be more effective design method in the point of signal integrity.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.1
• /
• pp.40-47
• /
• 2013

By virtue of Rec. ITU-R P.1546 and geography information system, interference analysis for the fixed wireless system and radar has been presented based upon the frequency-distance rules with minimum coupling loss, and a comprehensive methodology for assessing interoperability between systems was examined in terms of received signal, protection ratio, frequency dependent rejection. Also to find the antenna gain from a discrimination angle, a useful S-I plane was introduced based on signal and interference vectors derived from the real map with geographic information. To show some computational results, geography information on the map was taken for the given area, and field strength and path profile were illustrated for the radar and fixed wireless system operating at 2.7 GHz, for convenience. In addition the interference effect of receiver was also checked as a function of radar beam direction including protection ratio and frequency dependent rejection. The developed interference analysis can be actually applied to evaluate interoperability for wireless systems in the VHF and UHF bands.

• 한국정보통신설비학회:학술대회논문집
• /
• 2006.08a
• /
• pp.158-161
• /
• 2006

In this paper, we deal with EMI Analysis on Microstrip with Defected Ground plane. Specially, we investigate reflection, transmission, crosstalk, radiated emission on Microstrip with Defected Ground plane structure. And investigates undesired effects on various defected ground plane such as ground with split, slot, short end and open end gap. To analyze reflection, transmission and crosstalk of microstrip with defected ground plane, we used concept of the microstrip to slot line transition model. Besides, investigate radiated emission using FDTD Commercial tools such as CST MW

• Journal of Broadcast Engineering
• /
• v.18 no.3
• /
• pp.445-454
• /
• 2013

By using the radio propagation prediction of Rec. ITU-R P.1546, geographic information system, and S-I plane, we presented the methodology of interference analysis based on the minimum coupling loss, and also suggested the local coordinate system for calculating azimuth and elevation angles between the victim receiver and the interferer for an arbitrary antenna pattern. To check the presented algorithm, the map with the land-sea mixed area was taken for the given area of $80{\times}60[km^2]$ as real geography information. Field strength, path profile, and protection ratio with maximum allowable interference level have been illustrated for radar and fixed wireless system for the assumed frequency. In addition interference power of the victim receiver was calculated asa function of azimuth and elevation angles of the interferer. The developed methodology of interference analysis in the VHF and UHF bands can be actually applied to assess interoperability as well as compatibility in the civil or military applications.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.848-851
• /
• 2005

This paper proposes a design of IIR notch filter with modified pole placements. The pole angle is derived from quadratic programming to find the appropriate pole position on the unit circle in z-plane in order to achieve the symmetry of the amplitude response. The simulation results are shown when compared with the conventional design technique. Moreover, it uses the TMS320C31 DSP chip for hardware implementation. Finally, the hardware implementation can be applied to removal of ECG baseline wander and elimination of AC power line interference in ECG signal.

• Journal of electromagnetic engineering and science
• /
• v.6 no.1
• /
• pp.62-70
• /
• 2006

This paper presents a new power plane design method incorporating a single geometry derived from a unit cell of photonic bandgap(PBG) structure. This method yields constantly wide suppression of parallel plate resonances from 0.9 GHz to 4.2 GHz and is very efficient to eliminate PCB resonances in a specified frequency region to provide effective suppression of simultaneous switching noise(SSN). It is shown that with only two cells the propagation of unwanted high frequency signals is effectively suppressed, while it could provide continuous return signal path. The measured results agree very well with theoretically predicted ones, and confirm that proposed method is effective for reducing EMI, with measured near-field distribution. The proposed topology is suitable for design of high speed digital system.

• Journal of Sensor Science and Technology
• /
• v.21 no.2
• /
• pp.103-108
• /
• 2012

Radiofrequency(RF) signal is a key medium to the most of the present wireless communication devices including RF identification devices(RFID) and smart sensors. However, the most critical barrier to overcome in RFID application is in the failure rate in detection. The most notable improvement in the detection was from the introduction of EPC Class1 Gen2 protocol, but the fundamental problems in the physical properties of the RF signal drew less attention. In this work, we focused on the physical properties of the RF signal in order to understand the failure rate by noting the existence of the ground planes and noise sources in the real environment. By using the mathematical computation software, Maple, we simulated the distribution of the electromagnetic field from a dipole antenna when ground planes exist. Calculations showed that the dark area can be formed by interference. We also constructed a test system to measure the failure rate in the detection of a RFID transponder. The test system was composed of a fixed RFID reader and an EPC Class1 Gen2 transponder which was attached to a scanner to sweep in the x-y plane. Labview software was used to control the x-y scanner and to acquire data. Tests in the laboratory environment showed that the dark area can be as much as 43 %. One who wants to use RFID and smart sensors should carefully consider the extent of the dark area.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.199-205
• /
• 2007

In this paper, a novel hexagonal-shaped electromagnetic bandgap(EBG) power plane for the suppression of the ground bounce noise(GBN) in high-speed circuits is proposed. The proposed structure consists of hexagonal-shaped unit cells and detoured bridges connecting the unit cells. The hexagonal-shaped unit cells could omni-directionally suppress the GBN in digital circuits. The fabricated power plane's omni-directional -30 dB suppression bandwidth is from 330 MHz to 5.6 GHz. Then the proposed structure suppresses electromagnetic interference(EMI) caused by the GBN within the stopband. As a result, the proposed structure is expected to be conducive solving EMI problem in high-speed circuits.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.376-383
• /
• 2008

Generally a return current plane(RCP) of high speed digital and analog part is partitioned. This is achieved in order to decrease the noise interference between subsystem in PCBs(Printed Circuit Boards). However, when the connected signal line exists between each subsystem, this partition will cause unwanted effects. In a EMI(Electromagnetic Interference) point of view, the partition of the return current plane becomes a primary factor to increase the radiated emission. Component bridge(CB) is used for the way of maintaining radiated emission, still specific user's guide doesn't give sufficient principle. In a view point of EMI, design principle of multi-CB using method will be analyzed by measurement. And design principle of noise mitigation will be provided. Generally interval of multi-CB is ${\lambda}/20$ ferrite bead. In this study, When multi-CB connection is applied, design principle of ferrite bead and chip resistor is proved by measurement. Multi-connected chip resistance$(0{\Omega})$ is proved to be more effective design method in the point of EMI.

• Journal of Advanced Navigation Technology
• /
• v.22 no.4
• /
• pp.295-301
• /
• 2018

Recently, GPS(Global Positioning System) array antenna technology is generally used and widely adopted as a national infrastructure structure and aero-vehicles for protection the GPS signal reception. Until now, the 2-dimensional planar array is universally used for its applications in the array antenna signal processing, however relatively higher altitude air vehicles such as UAV experiences additional null zones induced by low altitude GPS interferences which is located in a symmetry zone of antenna horizontal plane and this could make the receiving antenna pattern coverage reduction. In this paper, we improved 20% of the beam pattern receiving performance and 13 dB correlation value improvement by eliminating the interference mirror images.