• 한국안전학회지
• /
• 제29권3호
• /
• pp.20-27
• /
• 2014

Cooling equipment is the frequent occurrence of fire despite the absence of the heating element. National fire statistics in 2013 show that a total of 263 fires occurred in the cooling equipment and the number of electric fan has 145 fire cases. This is accounted for 55.1% of the whole. Electric fan is the electrical appliance that the heat is generated on the winding wire and the iron core. If such characteristic is not controled properly, fire would break out at the electric fan. also there is a gap filled with an insulator between connection terminals of the capacitor in the electric fan. But in case that the gap on the capacitor is covered with some conductive material such as dust, there would be a fire as well caused by electrical heating locally. Although many studies related with those have been conducted, electric fan fire is continuously occurred. In this study, thermal characteristics and current signal in various conditions such as the heat generation of windings including iron cores of the motor and the dielectric breakdown of terminals on the capacitor connected to the motor were detected. In order to measure the maximum temperature, "third level" wind velocity button was pushed and the time selection switch to "continuation" was set. Analyzed data would be available for the fire safety of the electric fan.

• 한국철도학회논문집
• /
• 제8권6호
• /
• pp.533-538
• /
• 2005

In this paper we identity the hazard using HAZOP study for ATSRX which is a subsystem of the ATP system, and we study a safety management method for the mitigation of the risk to the acceptable level. ATSRX is a device that make a train which has a ATP system operate in ATS line. For this ATSRX send a induction signal with ATS system to vehicle controller. Thus ATSRX can be said a safety equipment that makes a train operate safely. In order to identify the hazard for the internal faults in ATSRX system, we employ HAZOP study method which is recommended as hazard identification in IEC 62278, RAMS requirements in railway signal, and also it provide the detail activity in IEC 61882. Thus, in this paper we perform HAZOP study based on ATSRX related standards and using the assessment of the identified hazard we study a method to guarantee the system safety through the change of the design to mitigate the risk to the acceptable level.

• Safety and Health at Work
• /
• 제10권2호
• /
• pp.213-218
• /
• 2019

Background: Motorcycles are one of the important members of commercial transportation because of the convenient use during congested traffic conditions and the ease of parking in narrow streets. This study investigates the characteristics of crashes and traffic signal violations caused by motorcycle couriers. Methods: From the national compensation data, this study analyzed the traffic crashes caused by 671 motorcycle couriers. Results: Among 671 injured couriers, 50.6% were aged less than 40 years, 49.2% run in a small business of <5 employees, and 47.2% had work experience of <6 months. Motorcycle crashes occurred mainly due to "rider overturned alone" (67.5%), in the daytime (73.5%), or on cloudy or clear days (77.2%). However, the violation rate caused by motorcycle couriers was high in couriers in a small business of <5 employees (13.9%), with work experience of <6 months (13.9%), on cloudy or clear days (12.4%), on an intersection (29.8%), in the type of "crash with a vehicle" (31.2%), or in a death accident (35.7%) Conclusion: The findings of this study can be used as a baseline in devising policies for preventing crashes of motorcycle couriers.

• 자동차안전학회지
• /
• 제13권3호
• /
• pp.41-46
• /
• 2021

The number of big traffic accident cases of pedestrian death appeared to be minor, however compared to death rate in car to car accidents is very high and quite a few of the pedestrian death rates among all traffic accidents are counted to be almost 40%. Previous pedestrian safety studies were mostly aimed at reducing the degree of pedestrian injuries from a vehicle to pedestrian collision, and less at preventing a collision itself. This research was conducted with a method of using road facilities to prevent vehicles from rushing into the sidewalk. This research used one of the collision analyzing programs, called PC-Crash to simulate the vehicle rushing into the sidewalk. Based on the program, it could derive an optimal safe zone location where the pedestrian can wait for the pedestrian light safely. Also, changing road facilities such as pedestrian light pillars or signal controllers can widen 440% compared to the present safe zone. Accordingly, researchers have to consider a method to analyze and apply pedestrian safe zones along with road facilities location when designing a road.

• 국제학술발표논문집
• /
• The 9th International Conference on Construction Engineering and Project Management
• /
• pp.736-743
• /
• 2022

Construction workers experience a high rate of fatal incidents from mobile equipment in the industry. One of the major causes is the decline in the acoustic condition of workers due to the constant exposure to construction noise. Previous studies have proposed various ways in which audio sensing and machine learning techniques can be used to track equipment's movement on the construction site but not on the audibility of safety signals. This study develops a novel framework to help automate safety surveillance in the construction site. This is done by detecting the audio sound at a different signal-to-noise ratio of -10db, -5db, 0db, 5db, and 10db to notify the worker of imminent dangers of mobile equipment. The scope of this study is focused on developing a signal processing model to help improve the audible sense of mobile equipment for workers. This study includes three-phase: (a) collect audio data of construction equipment, (b) develop a novel audio-based machine learning model for automated detection of collision hazards to be integrated into intelligent hearing protection devices, and (c) conduct field experiments to investigate the system' efficiency and latency. The outcomes showed that the proposed model detects equipment correctly and can timely notify the workers of hazardous situations.

• 한국산학기술학회논문지
• /
• 제17권3호
• /
• pp.450-456
• /
• 2016

케이블에 인가되는 신호로 의사잡음 수열을 사용하여 인가신호와 반사신호의 시간 상관 분석을 실시하여 케이블 고장을 검출하는 STDR (sequence time domain reflectometry)은 노이즈 환경에 강하고, 단선, 합선을 포함한 간헐적 고장의 검출이 가능한 것으로 알려져 있다. 하지만 고장 위치의 거리가 멀거나 경미한 고장의 경우 반사신호의 감쇄가 크고 상관계수가 작아지게 되어, 케이블 고장 판별이 어렵거나 측정 거리 오차가 커진다. 또한 위상과 피크치 검출에 의한 고장 탐지 자동화가 어렵게 된다. 따라서 본 논문에서는 기존의 STDR의 고장 검출 성능을 향상시키기 위해 케이블에 인가되는 인가신호의 상관계수의 최댓값을 검출하고, 다음으로 인가신호를 제거하여 반사신호의 상관계수의 최댓값을 검출하는 알고리즘을 제안하였다. 제안된 방법은 저압 전력 케이블에서의 고장 검출 실험을 통해 성능을 입증하였다. 그 결과 제안된 방법은 신호가 감쇄되더라도 전통적인 STDR보다 고장 여부의 정확한 구분과 위치의 추적이 가능하였다. 또한 기준신호 제거와 상관계수의 정규화를 통해 위상과 최대값 검출 방법을 사용함으로써 자동 고장 판별과 거리 계산에 오류가 발생하지 않았다.

• 대한교통학회:학술대회논문집
• /
• 대한교통학회 1995년도 제27회 학술발표회
• /
• pp.3-32
• /
• 1995

The Highway Capacity Manual specifies procedures for evaluating intersection performance in terms of delay per vehicle. What is lacking in the current methodology is a comparable quantitative procedure for ass~ssing the safety-based level of service provided to motorists. The objective of the research described herein was to develop a computational procedure for evaluating the safety-based level of service of signalized intersections based on the relative hazard of alternative intersection designs and signal timing plans. Conflict opportunity models were developed for those crossing, diverging, and stopping maneuvers which are associated with left-turn and rear-end accidents. Safety¬based level-of-service criteria were then developed based on the distribution of conflict opportunities computed from the developed models. A case study evaluation of the level of service analysis methodology revealed that the developed safety-based criteria were not as sensitive to changes in prevailing traffic, roadway, and signal timing conditions as the traditional delay-based measure. However, the methodology did permit a quantitative assessment of the trade-off between delay reduction and safety improvement. The Highway Capacity Manual (HCM) specifies procedures for evaluating intersection performance in terms of a wide variety of prevailing conditions such as traffic composition, intersection geometry, traffic volumes, and signal timing (1). At the present time, however, performance is only measured in terms of delay per vehicle. This is a parameter which is widely accepted as a meaningful and useful indicator of the efficiency with which an intersection is serving traffic needs. What is lacking in the current methodology is a comparable quantitative procedure for assessing the safety-based level of service provided to motorists. For example, it is well¬known that the change from permissive to protected left-turn phasing can reduce left-turn accident frequency. However, the HCM only permits a quantitative assessment of the impact of this alternative phasing arrangement on vehicle delay. It is left to the engineer or planner to subjectively judge the level of safety benefits, and to evaluate the trade-off between the efficiency and safety consequences of the alternative phasing plans. Numerous examples of other geometric design and signal timing improvements could also be given. At present, the principal methods available to the practitioner for evaluating the relative safety at signalized intersections are: a) the application of engineering judgement, b) accident analyses, and c) traffic conflicts analysis. Reliance on engineering judgement has obvious limitations, especially when placed in the context of the elaborate HCM procedures for calculating delay. Accident analyses generally require some type of before-after comparison, either for the case study intersection or for a large set of similar intersections. In e.ither situation, there are problems associated with compensating for regression-to-the-mean phenomena (2), as well as obtaining an adequate sample size. Research has also pointed to potential bias caused by the way in which exposure to accidents is measured (3, 4). Because of the problems associated with traditional accident analyses, some have promoted the use of tqe traffic conflicts technique (5). However, this procedure also has shortcomings in that it.requires extensive field data collection and trained observers to identify the different types of conflicts occurring in the field. The objective of the research described herein was to develop a computational procedure for evaluating the safety-based level of service of signalized intersections that would be compatible and consistent with that presently found in the HCM for evaluating efficiency-based level of service as measured by delay per vehicle (6). The intent was not to develop a new set of accident prediction models, but to design a methodology to quantitatively predict the relative hazard of alternative intersection designs and signal timing plans.

• 한국소음진동공학회논문집
• /
• 제22권12호
• /
• pp.1227-1236
• /
• 2012

The low speed machinery faults are usually caused by the bearing failure of the rolling elements. As the life time of the bearing is limited, the condition monitoring of bearing is very important to maintain the continuous operation without failures. A few monitoring techniques using time domain, frequency domain and fuzzy neural network vibration analysis are introduced to detect and diagnose the faults of the low speed machinery. This paper presents a method of fault detection for the rolling element bearing in the low speed machinery using the Wiener filtering and shock pulse counting techniques. Wiener filter is used for noise cancellation and it clearly makes the shock pulse emerge from the time signal with the high level of noise. The shock pulse counting is used to determine the various faults obviously from the shock signal with transient pulses not related with the bearing fault. Machine fault simulator is used for the experimental measurement in order to verify this technique is the powerful tool for the low speed machine compared with the frequency analysis. The test results show that the method proposed is very effective parameter even for the signal with high contaminated noise, speed variation and very low energy. The presented method shows the optimal tool for the condition monitoring purpose to detect the various bearing fault with high accuracy.

• 한국안전학회지
• /
• 제30권5호
• /
• pp.1-7
• /
• 2015

This paper is aimed to analyze the electrical and thermal signal such as ignition possibility, ignition time, thermal characteristics and arc fault power that are associated with electrical fire in case of the occurrence of series arc at IV wiring used for interior wiring at commercial power source. In order to analyze the signal, series arc was induced by generating the constant vibration through vibrating device in the one phase (R phase) and ignition possibility was analyzed along the condition of current value by adding cotton material to the contact point of wiring. The ignition time is shortened as the electric current value increased, burning time is not associated with current value and the temperature rose up to $740^{\circ}C$ though it was not ignited. It was checked out that the temperature was the energy source enough that can generate the fire related with insulation aging of wiring and the inflammable. The possibility of electrical fire by series arc was shown as more than 12% at 5A, more than 42% at 20A and arc showed 27W at 5A, 180W at 20A. It was confirmed that the possibility of electrical fire exists at the condition as above and the circuit breaker did not operate. This data can be used as the reference value for the investigation of electrical fire or development of the circuit breaker.

• 비파괴검사학회지
• /
• 제30권4호
• /
• pp.373-379
• /
• 2010

EMAT는 비접촉식 탐촉자인 동시에 모드 선택성이 우수하여 다양한 분야에 적용되고 있으나 근본적으로 에너지 전환효율이 낮아 신호 대 잡음비의 증가에 한계를 보인다. EMAT에 위상배열 기술을 접목하면 초음파의 집속 효과를 얻을 수 있으므로 낮은 전환효율의 문제를 극복하기 위한 하나의 해결방안이 될 수 있을 것으로 판단한다. 본 연구에서는 위상배열 EMAT에 대한 기초연구로 3~4개의 코일로 구성되는 표면파 및 수직횡파 발생용 위상배열 EMAT를 제작하고 각 요소코일에 공급하는 펄스의 지연으로부터 위상배열의 효과를 확인하고 방향특성을 측정하였다. 또한 시험편의 표면에 0.5 mm 깊이의 표면결함과 시험편 내부에 직경 0.5 mm의 측면 드릴 홀을 가공하여 제작된 위상배열 EMAT로 결함 신호를 검출하였으며, 이로부터 제작된 EMAT의 성능을 평가하였다.