• 한국통신학회논문지
• /
• 제22권4호
• /
• pp.685-695
• /
• 1997

In this paper, a new CMOS continuous-time fully-differential current-mode integrator is proposed as a basic building block of the low-voltage high frequency current-mode active filter. The proposed integrator is composed of the CMOS complementary circuit which can extend transconductance of an integrator. Therefore, the unity gain frequency which is determined by a small-signal transconductance and a MOSFET gate capacitance can be expanded by the complementary transconductance of the proposed integrator. And also the magnitude of pole and zero are increased. The unity gain frequency of the proposed integrator is increased about two times larger than that of the conventional continuous-time fully-differential integrator with NMOS-gm. These results are verified by the small signal analysis and the SPICE simulation. As an application circuit of the proposed fully-differential current-mode integrator, the three-pole Chebyshev lowpass filter is designed using 0.8.$\mu$m CMOS processing parameters. SPICE simulation predicts a 3-dB bandwidth of 148MHz and power dissipation of 4.3mW/pole for the three-pole filter with 3-V power supply.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1984년도 추계학술발표회 논문집
• /
• pp.33-35
• /
• 1984

A new type single beam photoacoustic spectrometer suitable for measuring optical absorption of condensed powder matter with the automatic calibration capability of a source power spectrum is introduced. The signal processing until of this spectrometer consists of a photoacoustic cell a lock-in amp., a switching circuit and a personal computer. The measured optical absorption spectra of a few material by this method are good agreement with the results obtained by the double-beam photoacoustic spectrometer.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.336-340
• /
• 1996

This paper presents the development of a collocated capacitance sensor and its application to the decentralized PID controller design for 4-axis magnetic bearing system. The main feature of the sensor is that it is made of a compact printed circuit board (PCB) so that it can be built in to the actuator coil of the magnetic bearing unit. The signal processing unit has been also developed. Then, decentralized PED controller is designed using simplified rotor system model. Finally, the experimental results on the performance of the collocated sensor based decentralized PID controller for a magnetic bearing rotor system is presented.

• 대한방사선방어학회:학술대회논문집
• /
• 대한방사선방어학회 2011년도 추계 학술발표회 및 심포지엄
• /
• pp.122-123
• /
• 2011

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(2)
• /
• pp.157-160
• /
• 2002

This paper proposed a guideline for selecting the arithmetic circuit architecture. The guideline incorpo-rates the new concept of PDSP (power-delay-size product) and the weighting method. HSPICE simulations havc been performed to several full adders in order to prove the validity of the proposed guideline. We applied this guideline to select an optimized FA (full adder) architecture and successfully implemented the DAC's digital blocks.

• 한국음향학회지
• /
• 제5권3호
• /
• pp.13-20
• /
• 1986

본 논문은 신호처리가 가능한 2진 로가리즘 상수를 발생시키기 위한 programmable variable-rate up/down 계수기의 설계를 기술한다. 2진수에 대한 밑수가 2인 로가리즘 계승의 적용은 결 과적으로 오차가 발생한다. log\sub 2\(1+χ)-χ에 의해 정의된 것처럼 log\sub 2\(1+χ)에서의 오차는 직선의 집합으로 갖게된다. 계수기 rate는 직선의 기울기에 비례한다. 그러므로 신호처리가 가능한 2진 로가리즘 상수는 programmable 계수기를 사용함으로써 쉽게 발생될 수 있다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.256-258
• /
• 1999

In this article, an integrable circuit technique for implementing square root extractor for analog signal processing is described. The realization method makes use of the characteristic of MOS translinear principle. The proposed scheme achieves a wide dynamic range, wide-band capability and high accuracy. Simulation results demonstrating the performance of the proposed scheme are also presented.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.289-292
• /
• 2001

A Novel fully-differential bipolar current-controlled current amplifier(CCCA) for electrically tunable circuit design at current-mode signal processing were designed. The CCCA was consisted of fully-differential subtracter and fully-differential current gain amplifier. The simulation result shows that the CCCA has current input impedance of 0.5 Ω and a good linearity. The CCCA has 3-dB cutoff frequency of 20 MHz for the range over bias current 100$mutextrm{A}$ to 20 ㎃. The power dissipation is 3 mW.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 하계종합학술대회 논문집
• /
• pp.199-202
• /
• 1999

In this paper, a possibility of building various types of RF passive components using the silicon micromachining technique has been examined with special emphasis on the wireless and mobile communication applications. Silicon micromachining technique is compatible with conventional silicon IC process and could provide a possibility of integrating base-band signal processing units and RF passive and active circuit components all in one silicon wafer rendering implementation of system-on-chip paradigm for future mobile and wireless communication systems.

• ETRI Journal
• /
• 제10권2호
• /
• pp.32-39
• /
• 1988

In this paper, we describe an effective trunk loop signal processing method and anlayze execution time of the program in the DTCP (Digital Trunk Circuit Processor) in the TDX-1A digital switching stytem. And we also predict a maximum trunk capacity in the DTCP with respect to scanning period based on the call attempt characteristics which has the Poisson distribution.