• Journal of the Korean Wood Science and Technology
• /
• v.17 no.2
• /
• pp.1-12
• /
• 1989

To study the structure of opposite wood in the angiosperms. samples were cut from stems and branchs of 10 spcies growing in Korea. The opposite side was defined as being along a line passing from the most wide annual ring of the tension wood on the upper side to the pith and extrapolated through the opposite side. lateral sides being on the right and left of this line. The stem woods growing almost horizontally were surveyed the structural features of the well-developed opposite wood for the tension wood. In the annual-ring of the well-developed opposite woods. an investigation was made on how the dimension of elements, microfibril angles. and cell wall layers change from tension side to opposite side. The structural characteristics of opposite wood in hardwoods realized in this study are as follows: 1. The vessel diameters increased continuously to ward the opposite side in which the values were maximum. The vessel length also increased toward opposite side. but the rates of increase were smaller than those in the vessel diameters. 2. The wood fiber length were decreased from tension toward opposite side. but the rates of decrement were f1actuated within the sampled species. 3. The microfibril angles had the minimum values on the tension side. then increased steeply toward the opposite side in which the values maximum. 4. In the percentage of elements the vessel elements increased continously at a relative rate from the tension to opposite side, whereas the values of the wood fibers were lower in the opposite than the tension side, but the' variation patterns of rays were not seem distinctly. 5. The component layers of the wood fiber in the opposite woods were very similar to the lateral woods.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.1
• /
• pp.3-18
• /
• 1985

In Korea, a study on the anatomical features of pitch pine (pinus rigida Miller) branch wood through photo-microscopical method was reported in 1972 by Lee. Therefore, as a further study of Lee's on the anatomical features in branch wood of pinus rigida miller that grows in Korea, compression wood, opposite wood, and side wood were selected and treated for the purpose of comparing their structures revealed on cross and radial surface through scanning electron microscope in this study. The obtained results in this study were summarized as follows; 1. The trachied transition from earlywood to late wood is very gradual and the tracheids are nearly regular in both arrangement and size in compression wood but this transition in opposite wood and side wood is abrupt and the tracheids in opposite wood and side wood are less regular than those in compression wood. Also, the annual ring width of opposite wood is narrower than that of compression wood or side wood and the rays revealed on cross surface of side wood are more distinct than compression wood and opposite wood rays. 2. The tracheids of compression wood show roundish trends especially in earlywood but those of opposite wood and side wood show some angular trends. And intercellular space, helical cavity, and spiral check are present in both earlywood and latewood of compression wood but not present in opposite wood and side wood irrespective of earlywood and latewood. 3. The wall thickness of latewood tracheid is similar to that of earlywood tracheid in compression wood whereas the wall thickness of latewood tracheid is by far thicker than that of earlywood tracheid in opposite wood and side wood and the S3 layer of secondary wall is lack in compression wood tracheid unlike opposite wood and side wood tracheid. 4. The tracheids in compression wood are often distorted at their tips unlike those in opposite wood and side wood and the bordered pit in compression wood tracheid is located at the bottom of helical groove unlike that in opposite wood and side wood tracheid. 5. The bordered pits in radial wall of opposite wood and side wood tracheids are oval in shape but those of compression wood tracheids show some modified oval shape. 6. In earlywood of side wood, the small apertures of cross-field pits are roundish triangle to rectangle and the large one are fenestriform through the coalition of two small ones. However, the small apertures of cross-field pits are upright oval and the large ones are procumbent oval shape in earlywood of opposite wood and the apertures of cross-field pits in compression wood are tilted bifacial convex lens shape in earlywood and slit in late wood because of the border on tracheid side.

• Journal of Korean Society of Forest Science
• /
• v.78 no.2
• /
• pp.119-131
• /
• 1989

This experiment was executed to investigate and compare qualitative and quantitative anatomical features in compression wood, opposite wood, and side wood formed in a bent stem, a straight branch, and an exposed horizontal root of Korean red pine(Pinus densiflora S. et Z.). The respective four discs containing compression wood taken at 20cm interval both in stem and branch as well as a disc containing well developed compression wood from horizontal root were analyzed. Percentage of compression wood and eccentricity showed decreasing tendency with the increasing distance in height direction of stem and length direction of branch. The qualitative anatomical features of compression wood appeared to differ from those of side and opposite wood in very gradual tracheid transition from earlywood to latewood, roundish tracheid shape on cross surface, tracheid distortion at tip on radial surface, existence of intercellular space, and helical cavity in tracheid wall. And the differences in these qualitative features among the compression wood, opposite wood, and side wood became less intensive with the decreasing trends in percentage of compression wood and eccentricity. The quantitative anatomical features in compression wood also appeared to be wider in that respective widths of fusiform and uniseriate ray than those of opposite and side wood, but the heights of fusiform and uniseriate ray in compression wood were smaller than in opposite and side wood. The number of horizontal resin canal(fusiform ray) and uniseriate ray, however, showed no differences among the compression wood, opposite wood, and side wood. And the number of vertical resin canal in unit area, $4{\pi}mm^2$ of compression wood was fewer than that in opposite wood, whereas numerous vertical resin canals contained in a growth ring. These rays of compression wood seemed to be characterized by smaller height and wider width than those of opposite and side wood.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.4
• /
• pp.6-12
• /
• 1998

Test results of domestic softwood lumber were presented to examine the notch effect of beams and compare to present AIJ(Architecture Institute of Japan) formula in notched wood member especially positioned in bottom side (tension side) of a beam. Notched lumber was tested under following condition : each specimen supported simply, and subjected to third-point loading at points of 1/3 of the span length. Notch was located opposite side to loading direction and notch depth were 1/6, 1/4, 1/3 of beam depth. Deflection and load were measured by digital dial guage each in 25kgf increment. Bending test results were as follows; Mpro/Mmax range (proportional and maxium bending moment ratio in notched beam) was 0.5 - 0.65. It was considered that maxium bending moment was about 1.5 times to proportional bending moment in notched beam and showed same tendency in the test result of ordinary wood specimens. AU standard formula for the tension side notch, Mmat = 0.6 ${\times}$ (Zo $\sigma$), the constant 0.6 was suitble for notch ratio(notch depth to beam depth) 1/6, but this ratio for 1/4, and 1/3 was not. So it is preferable to accept smaller value than 0.6 for notch ratio more than 1/3. These experiment results showed critical effect in tension side notched wood beam especially in greater than notch ratio 1.3 of wood beam. From the above results, it is recommened to revise design formula adoptable to domestic wood constructon member with tension side notched member.

• Journal of Plant Biology
• /
• v.33 no.4
• /
• pp.285-292
• /
• 1990

In order to elucidate the formation of reaction tissues during the transition from primary to secondary growth, the developmental anatomy was conducted in the first internode of Ginkgo biloba seedling in horizontal position. The righting of the horizontal first internode took place at the middle portion and gradually proceeded to the base during the primary growth. Reaction tissues were formed corresponding to the righting movement in the horizontal first internode. During the transition from primary to secondary growth, compression wood was gradually developed on the lower side only. The anatomical features of compression wood also extended longitudinally to the lower side of the vertical portion where it coincided with the lower side of the horizontal first internode occurs acropetally from basal to apical portion. Eventually, some of the anatomical features of compression wood occurred at the primary growth. And the typical compression wood is gradually established during the secondary growth. On the other hand, the lower side tracheid and ray were longer and higher than those of the upper side in the horizontal first internode. However, difference in the width of ray was not observed between the lower and upper sides.

• Journal of the Korea Furniture Society
• /
• v.11 no.2
• /
• pp.7-12
• /
• 2000

This paper describes the bending strength properties of laminated woods which had three kinds of specimens according to finger length-12, 4.5 mm and butt joint and the acoustic emissions (AEs) generated during the test. 3-ply laminated wood beams were tension side layers (lower layers) composed of one middle lamina and two side-jointed laminae, with one butt joint ($_1BJ$), one finger joint (12mm, $_1FJ_{12}$) or one finger joint (4.5mm, $_1FJ_{4.5}$) in the middle lamina of tension side layer. And 3-ply laminated wood beams were tension side layers (lower layers) also composed of one lamina, with one butt joint (BJ), one finger joint (12mm, $FJ_{12}$) or one finger joint (4.5mm, $FJ_{4.5}$/) in tension side layer. Cryptomelia pieces were cut for butt and two finger types and glued with resorcinol-phenol resin adhesive. The results were as follows It was not effective in the bending modulus of elasicity (MOE) with IFJL type and had no difference from finger length. The bending modulus of rupture (MOR) of laminated wood beams including finger joint was the same values as that including butt feint and had no difference from finger length. It was effective in MOE with FJL type and had no difference from finger length. The effect of finger joint on MOR was much higher than that of butt joint but had no difference from finger length. The AE generation time of IFJL type was earlier than that of the control wood and the number of AE count was much more than that of the control wood. However, the AE generation time of FJL type was earlier than that of the control wood and the number of U count was much fewer than that of the control wood.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.2
• /
• pp.20-28
• /
• 2008

This study was carried out to provide the so-called circumferential slicing method for investigating radial distributions of the tangential strains and of moisture contents within the log cross section (LC) of Kalopanax pictus during indoor drying it. While the heartwood showed an almost uniform moisture content distribution in the range of about 50~55% in case of the green wood, it has gradually decreased toward the outer side, showing about 19% of moisture content difference from the innermost slice. Although the moisture gradient along the radial direction has gradually become gentle as drying progresses, the sapwood of the outer side represented the moisture contents below the fiber saturation point after 24 hours of drying while the heartwood in the inner part showed the moisture contents higher than the fiber saturation point. The pith side was laid under the tensile stress after 24 hours of drying, and then gradually decreasing toward the bark side, and showed the distribution being switched again to the tensile stress on the bark side. As the drying has progressed, this trend got more intensified, and finally showed the U-shaped distribution model after 48 hours of drying. The circumferential slice test is considered to be suitable in quantitatively determining the tangential strains and moisture content within a LC.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.2
• /
• pp.79-85
• /
• 1990

Traditional complex joints have used to a wide variety of wooden furniture construction. Dowel joint is the most popular joint s. However design of this joint to meet specified service condition has been hampered by a lack of proven design formulas which can be use to predict their strength. The object of this study is to investigate the withdrawal strength and effect of dowel diameters in wood and wood based materials. The obtained results were as follows; 1. The relationship between withdrawal strength and dowel diameter is found to be linear. 2. Withdrawal strength of medium density fiberboard and Sepetir in end-to-side joints is superior to Antiaris, particleboard and plywood. 3. In end-to-end joints, withdrawal strength of medium density fiberboard is the most superior joint. but Sepetir. Antiaris and plywood have similarly strength and particleboard is inferiority. 4. Withdrawal strength in end-to-end joints of Antiaris and plywood is higher than in end-ta-side joints. But in end-to-end joints of Sepetir. medium density fiberboard and particleboard is similarity in end-to-side joints.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.3
• /
• pp.20-27
• /
• 1989

This experiment was made to find the peripheral variations of annualring widths, the cell dimensions, microfibril angles and bulk densities within each annual-ring of horizontal-growing young tree of beech(Betul a platyphylla var. japonica) and Oak (Quercus variabilis) from the tension to the opposite side. Also a comparision between the features of the obnormal annual ring for horizontal-growing year and normal annual ring for the straight-growing years was made. The dimension of propotion of the element, the microfibril angles and the bulk density decreased or increased continuously toward opposite side which showed minimum or maximum value. The dimension of elements the microfibril angles and the bulk density decreased or increased continuously towards opposite side which showed minimum or maximum value. The dimension of elements. the microfibril angles and the bulk density in the normal annual rings were similar to those in the lateral woods. whereas were significantly more different in the tension wood than in the opposite wood. The features of typical opposite wood in the hardwoods were influenced by the locations within the inclined stems than effects of the decrease in the annual ring width. The oppostie woods in hardwoods did not conform to the tension wood and lateral wood. The abnormal annual ring included the opposite wood, lateral wood similar to normal wood and tension wood having specialized structure even in the same annual ring.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.1
• /
• pp.75-80
• /
• 1996

The purpose of this study is to clarify the mechanism of moisture transfer depend on the thickness of the spruce(Picea sitchensis Carr.). Therefore, as the basic research of moisture transmission, the amount of moisture transmission and the moisture distribution in specimens and temperature of it's surfaces in vapor transmission process were investigated. The experiment was conducted in a steady state. and the moisture distribution was measured by knife cutting and weighing the specimens. The following conclusions were obtained ; 1. It can be found that distribution of moisture in the specimen can be approximated by two different straight lines intersecting at nine or ten percent moisture content. The amount of moisture movement defends on the gradient of moisture in the wood. 2. It is investigated that the wood surface moisture contents(MCs) are less for thinner specimens than for thick ones on the absorption side. On the other hand, the wood surface MCs are greater for thinner specimens than for thick ones on the desorption side. The main factor that affects the EMC of wood would be temperature when the relative humidity of atmosphere is constant. The specimen generate heat with the absorption and desorption process. In addition, the velocities of moisture transmission varied with the thicknesses of specimens. If the temperature of wood becomes greater, its MC decreases. Then the difference between surface MC and EMC of adsorption and desorption side becomes greater for thinner specimens. Therefore it is considered that the coefficients of moisture transfer decreases with the increases of the specimens' thicknesses.