• 한국세라믹학회지
• /
• 제34권6호
• /
• pp.601-610
• /
• 1997

In cofiring of multilayered alumina with tungsten, the change of camber with lamination condition was experimented and the effect of sintering shrinkage of alumina and tungsten was investigated. From the exact measurement of sintering shrinkage of tungsten thick film, as lamination pressure increased, the sintering shrinkage of alumina decreased but that of tungsten thick film was not changed. So it was though that the main factor which induced the sintering shrinkage difference between ceramics and metal with lamination condition was the change of sintering shrinkage of ceramics. In case of high lamination pressure, high green sheet density, the cofired specimen showed low camber due to low shrinkage difference between alumina and tungsten and there was a linear relation between camber and shrinkage difference. It was found that this shrinkage difference could change the thickness of tungsten film and the microstructure within via hole during cofiring.

• 한국의류학회지
• /
• 제28권8호
• /
• pp.1057-1064
• /
• 2004

Silk, polyester, cotton, and wool fabrics were embroidered with varying stitch length of 3mm, 5mm, and 10mm to examine the difference in fabric shrinkage in terms of sewing direction, fabric thickness, cover factor, stitch length, and fiber type. Warp, filling, and bias direction of sewing resulted in no difference in fabric shrinkage. Within the samples with same stitch length, there was less fabric shrinkage in fabrics with higher fabric thickness or higher cover factor. There was larger shrinkage when sewn with longer stitch length. Comparing fabrics with different fiber types but similar fabric thickness, silk and polyester fabrics showed the smallest fabric shrinkage and wool fabrics showed the largest shrinkage. It is shown that similar fabric shrinkage between silk and polyester is due to the similarity in cover factor.

• 대한치과기공학회지
• /
• 제29권2호
• /
• pp.9-15
• /
• 2007

As the development of nanotechnology, the use of composite resins which containing nanofillers becomes popular. The purpose of this study was to test the degree of polymerization of nanofillercontaining composite resins. For the study, three different nanofiller-containing composite resins and two different light-curing units were used. To evaluate the degree of polymerization, the maximum polymerization shrinkage taking place during the light curing, and the microhardness, after the light curing, were measured. As results, two light-curing units exhibited a similar emission spectrum to that of the included photoinitiator, camphorquinone. The only difference between the light-curing units were the width of the emission spectrum. Three different composite resins showed different microhardness values. Among them, Grandio showed the greatest microhardness value. However, there was less microhardness difference on the top and bottom surfaces due to the difference of the light-curing units. The maximum polymerization shrinkage values were also similar in the tested specimens regardless of the difference of the light-curing units. However, Grandio showed the least polymerization shrinkage. According to the manufacturers' data, Grandio showed the highest filler content(vol%).

• 한국세라믹학회지
• /
• 제33권12호
• /
• pp.1373-1379
• /
• 1996

Change of sintering shrinkage in alumina-based multilayer ceramics was observed in various lamination condi-tions and binder burnout (BBO) temperatures. It was found that the linear shrinkages in X and Y directions were nearly the same with the BBO temperatures but a large shrinkage difference in Z direction was observed. However this phenomenon was diminished when BBO temperature was increased. A linear relationship between the laminated density and the sintering shrinkage was found and the slope was independant on the BBO temperature but dependant on the shrinkage direction.

• 대한토목학회논문집
• /
• 제33권2호
• /
• pp.729-737
• /
• 2013

콘크리트 포장의 환경하중은 온도하중과 수분하중으로 구분할 수 있으며, 이는 콘크리트 슬래브 내의 온도분포와 건조수축 및 크리프를 의미한다. 본 연구에서는 공항 콘크리트 포장의 역학적 설계에 필요한 환경하중을 산정할 수 있는 방법을 개발하였다. 먼저, 대상 지역과 설계 슬래브 두께를 결정한 후, 포장 온도 예측 프로그램을 사용하여 예측된 슬래브 깊이에 따른 콘크리트 온도분포를 등가선형 온도차이로 환산하였다. 기존 건조수축 예측 모형을 개선하여 지역별 상대습도를 고려하여 콘크리트의 건조수축을 예측한 후 부등건조수축 등가선형 온도차이로 환산하였다. 또한, 응력이완을 건조수축에 반영하였다. 결국, 온도에 의한 등가선형 온도차이와 수분에 의한 부등건조수축 등가선형 온도차이를 합하여 최종 환경하중인 총 등가선형 온도차이를 산정하였다. 적용 예를 보이기 위해 지역별 기상조건을 대표할만한 국내 민간공항 8곳 및 군공항 2곳의 환경하중을 본 연구에서 개발된 방법으로 계산하고 비교하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 추계 학술논문 발표대회
• /
• pp.88-89
• /
• 2017

Curling is caused by the shrinkage difference between surface and bottom side of concrete, and the cracks can be occurred by vehicle load after curling. It is important to investigate and predict the curling behavior to minimize the quality defect of concrete due to the curling. Therefore, the experimental and analytical investigation was carried out.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.175-180
• /
• 1999

The heating system of korea apartment house is called Ondol. The surface finishing mortar of this floor system typically used the cement based mortar, where the surface finishing mortar easily appears the crack. To order to crack control, the cement that added expansive additive used to reducing dry-shrinkage. For the surface finishing mortar, the types of shrinkage is known as plastic shrinkage, dry-shrinkage and autogenous This experimental study is to investigate the difference on dry-shrinkage of the cement that added expansive additives and OPC. The test method is varied the ration of water/cement (W/C) and the ratio of sand/cement(S/C). For OPC, The increase of the ratio of S/C is reduced dry-shirnkage but for the cement that added expansive additives, the increase of the ratio of S/C is augmented dry-shrinkage For OPC, The increase of the ratio of W/C is augmented dry-shrinkage but for the cement that added expensive, the increased of the ratio of W/C is reduced dry-shrinkage.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 춘계 학술논문 발표대회
• /
• pp.151-152
• /
• 2016

In this study, the shrinkage properties of concrete with the high-performance shrinkage admixture and the crack reinforcing materials applied to the high-flatness flooring of hypermarkets, outlets and warehouses was evaluated. The concrete with the popular shrinkage admixture is significantly reduced compared to the plain concrete without shrinkage admixture for the dry shrinkage deformation, and the difference of shrinkage ratio between the concretes has been shown to increase with increasing age.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.9-10
• /
• 2017

In case of the concrete is poured into the HPC(Hollow Precast Concrete) column, the shrinkage condition of the HPC surface and the infilled concrete may be different, causing an interfacial space and deteriorating the integration performance. In this study, manufacturing HPC column mold and and the drying shrinkage properties with the charging concrete were examined. As a result, case of the shrinkage reducing agent showed the best drying shrinkage reduction effect. In the case of the expansive agent, the length change was lower than that of plain, but the difference from the shrinkage reducing agent was large, so it is considered that mixing condition of expansion mixing condition should be improved.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.58-64
• /
• 2004

The shrinkages of injection molded parts are different in molding operational conditions, resins and additives. The shrinkage of injection molded part for crystalline polymer, PBT (polybutylene terephthalate) has been studied for various operational conditions of injection molding and content of additives. Mica was used as a additive to PBT to examine the part shrinkage according to the mica content. The part shrinkages of mica contained PBT decreased as mica content increases. Higher injection temperature and injection pressure resulted in a lower shrinkage. As mold temperature increases the part shrinkage decreased. The part shrinkage of flow direction was less than that of the perpendicular direction to the flow for both pure and mica contained PBT. However the shrinkage difference between flow and perpendicular to flow directions decreased as mica content increased.