• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.6
• /
• pp.505-510
• /
• 2013

An encircling send-receive type pulsed eddy current (PEC) probe is designed for use in aluminum tube inspection. When bare receive coils located away from the exciter were used, the peak time of the signal did not change although the distance from the exciter increased. This is because the magnetic flux from the exciter coil directly affects the receive coil signal. Therefore, in this work, both the exciter and the sensor coils were shielded in order to reduce the influence of direct flux from the exciter coil. Numerical simulation with the designed shielded encircling PEC probe showed the corresponding increase of the peak time as the sensor distance increased. Ferrite and carbon steel shields were compared and results of the ferrite shielding showed a slightly stronger peak value and a quicker peak time than those of the carbon steel shielding. Simulation results showed that the peak value increased as the defect size (such as depth and length) increased regardless of the sensor location. To decide a proper sensor location, the sensitivity of the peak value to defect size variation was investigated and found that the normalized peak value was more sensitive to defect size variation when the sensor was located closer to the exciter.

• Journal of KIISE:Computer Systems and Theory
• /
• v.29 no.6
• /
• pp.354-360
• /
• 2002

Delay estimation must be simple and efficient, since millions or more delay calculations may be required during a timing-driven placement stage. We have developed a new Modified Elmore delay estimation method, which is significantly more accurate than the original Elmore delay by considering resistance shielding effects, but has the same order of complexity with that of Elmore delay. Experimental results show that the suggested technique can significantly reduce the error in estimated delay, from 31.6 ~ 145.2% to 2.5 ~ 22.7%.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.2
• /
• pp.122-129
• /
• 2001

A characterization procedure for analyzing symmetric coupled MIS(Metal-Insulator-Semiconductor) transmission line is used the same procedure as a general single layer symmetric coupled line with perfect dielectric substrate from the extraction of the characteristic impedance and propagation constant for even- and odd-mode. In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite- Difference Time-Domain(FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Symmetric coupled MIS transmission line parameters for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency- dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.950-954
• /
• 2003

This paper presents the delivered power and reflection coefficient in metallic shielding enclosure excited by the interior source, which are evaluated with the method of moments, and describes a method for reducing the radiation of electromagnetic fields in the cavity by putting lossy dielectric material in one inside wall. In this paper we introduce carbon polystyrene-foam as lossy dielectric material and observe it's effects of reduction when the thickness and permittivity of lossy dielectric material are changed. The results show that the reduction of the electromagnetic radiation can be achieved by controlling the amount of carbon in lossy dielectric material. The theoretical analysis is verified by the measured delivered power.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.7
• /
• pp.843-850
• /
• 2003

Cu/PET film composites were prepared by electroless copper plating method. In order to improve adhesion between electroless plated Cu layer and polyester (PET) film, the effect of pretreatment conditions such as etching method, mixed catalyst composition were investigated. Chemical etching and plasma treatment increased surface roughness in decreasing order of Ar＞HCl＞O$_2$＞NH$_3$. However, adhesion of Cu layer on PET film increased in the following order: $O_2$＜Ar＜HCl＜NH$_3$. It indicated that appropriate surface roughness and introduction of affinitive functional group with Pd were key factors of improving adhesion of Cu layer. PET film was more finely etched by HCI tolution, resulting in an improvement in adhesion between Cu layer and PET film. Plasma treatment with NH$_3$produced nitrogen atoms on PET film, which enhances chemisorption of Pd$^{2+}$ on PET film, resulting in improved adhesion and shielding effectiveness of Cu layer deposited on the Pd catalyzed surface. Surface morphology of Cu plated PET film revealed that Pd/Sn colloidal particles became more evenly distributed in the smaller size by increasing the molar ratio of PdCl$_2$; SnCl$_2$from 1 : 4 to 1 : 16. With increasing the molar ratio of mixed catalyst, adhesion and shielding effectiveness of Cu plated PET film were increased.d.

• Journal of Sensor Science and Technology
• /
• v.25 no.3
• /
• pp.229-234
• /
• 2016

Self-powered neutron detector (SPND) is being widely used to monitor the reactor core of the nuclear power plants. The SPND contains a neutron-sensitive metallic emitter surrounded by a ceramic insulator. Currently, the vanadium (V) SPND has been being developed to be used in OPR1000 nuclear power plants. Some Monte Carlo simulations were accomplished to calculate the initial sensitivity of vanadium emitter material and alumina insulator with a cylindrical geometry. An MCNP code was used to simulate some factors (neutron self-shielding factor and beta escape probability from the emitter) and space charge effect of an insulator necessary to calculate the sensitivity of vanadium detector. The simulation results were compared with some theoretical and experimental values. The method presented here can be used to analyze the optimum design of the vanadium SPND and contribute to the development of TMI (Top-mount In-core Instrumentation) which might be used in the SMART and SMR.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.4
• /
• pp.79-83
• /
• 2018

An accurate method to measure shielding effectiveness(SE) of EMI spray coating film is presented. After high frequency simulating, Circular coaxial standard test fixture is fabricated. A sample of EMI spray coating film was fabricated for insertion into a circular coaxial standard test fixture. The measuring instrument used an Agilent 8722ES vector network analyzer for the SE measurement. The exact SE of copper and silver mixed spray coating sample was measured by the composition of the measuring instrument and the measuring sample. The SE of copper sample was measured at 70 dB and the SE of copper and silver mixed spray coating sample was measured at 60 dB. As a result of the measurement, the reliability of the circular coaxial standard test fixture was confirmed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.7
• /
• pp.748-751
• /
• 2013

We perform a wideband radiated pulse coupling analysis of simple building structures using the finite-deference time-domain(FDTD) method. Toward this purpose, the building structures composed of concrete and window materials are assumed and we numerically model the electrical properties of each material. In this work, we apply a dispersive FDTD algorithm for the electromagnetic analysis of building structures and investigate their shielding effectiveness in the frequency range of 50 MHz to 1 GHz.

• Nuclear Engineering and Technology
• /
• v.25 no.4
• /
• pp.561-569
• /
• 1993

DOT4.2-QAD-CG coupling method was used to analyze the dose rates outside the side and the bottom shield system of CANDU 6 plant. The average dose rates at the main airlock and the new fuel loading area are approximately 6 $\mu$Sv/h as it is required. The calculated dose rates have a good agreement with the measurements at the operating CANDU 6 plant. The method used in this paper can be applied to the radiation shielding analysis of Wolsong 2, 3, and 4 CANDU 6 type plants which will be constructed in the near future.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.10 no.1
• /
• pp.37-43
• /
• 2012

Radioactive waste transport package was developed to transport eight drums of low and intermediate level waste(LILW) in accordance with the IAEA and domestic related regulations. The package is classified with industrial package IP-2. IP-2 package is required to undergo a free drop test and a stacking test. After free drop and stacking tests, it should prevent the loss or dispersal of radioactive contents, and loss of shielding integrity which would result in more than 20 % increase in the radiation level at any external surface of the package. The objective of this study is to establish the safety test method and procedure for stacking test and to prove the structural integrities of the IP-2 package. Stacking test and analysis were performed with a compressive load equal to five times the weight of the package for a period of 24 hours using a full scale model. Strains and displacements were measured at the corner fitting of the package during the stacking test. The measured strains and displacements were compared with the analysis results, and there were good agreements. It is very difficult to measure the deflection at the container base, so the maximum deflection of the container base was calculated by the analysis method. The maximum displacement at the corner fitting and deflection at the container base were less than their allowable values. Dimensions of the test model, thickness of shielding material and bolt torque were measured before and after the stacking test. Throughout the stacking test, it was found that there were no loss or dispersal of radioactive contents and no loss of shielding integrity. Thus, the package was shown to comply with the requirements to maintain structural integrity under the stacking condition.