• Tunnel and Underground Space
• /
• v.13 no.3
• /
• pp.169-179
• /
• 2003

Anisotropic shear strength of rock joints is studied based on the artificially fractured specimens using experimental and analytical methods. Series of direct shear tests are performed to obtain the strength, stiffness and friction angle of joints under various low normal stresses and shearing directions. The results of shear strength and stiffness show anisotropic value according to shearing direction under low normal stress specially less than 2.45 MPa. But, the effect of joint roughness on strength decreases with increasing normal stress. To estimate more effectively the peak shear strength under low normal stress, the modified Barton's equation is suggested.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.8 no.2
• /
• pp.47-57
• /
• 1984

Effect on the hand value and mechanical properties of blend ratio and weight had been investigated Oil summer suits for men. Relation between the mechanical properties and the deformation in behavior was also studied. The mechanical properties which influence the hand values and total hand value had been discussed and the relation between mechanical properties, hand values and fabric count had, too. As result, the following conclusions had been obtained. 1) The values of tensile properties increased with the increase of blend ratio of wool. The values of surface properties increased according to the increase of blend ratio of polyester. 2HB(bending properties) of polyester/wool blend showed higher value than that of $100\%$ wool, but there was no change in the shearing properties according to the blend ratio. The values of stiffness, crispness and anti-drape stiffness of blend fabric showed higher values than those of $100\%$ wool fabric. The value of fullness (including softness) of blend fabric showed lower value than that of $100\%$ wool fabric. 2) The correlation between hand values and mechanical properties showed following order. in stiffness : bending properties>surface properties in crispness: surface properties>bending properties in anti-drape stiffness: bending properties>surface properties>shearing properties.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.434-438
• /
• 2003

The shearing process for the sheet metal is normally used in the precision elements such as semi-conductor components. In these precision elements, the burr formation brings a bad effect on the system assembly and demands the additional de-burring process. In this paper, we have developed the desktop-type precision punching system to investigate the burr formation mechanism and present kinematically Punch-die auto aligning methodology, for the purpose of burr unifomizing and minimizing, between the rectangular shaped punch and die. By using the scanning electron microscope, the aligned punching results are compared with the miss-aligned ones. Also, we measured the relative burr heights using the self-designed laser measuring device for insitu self aligning. Since it is hard to get the perfect, so called, burr-free edges during the shearing process, we introduced the ultrasonic do-burring machine. The de-burring operation was carried out by a novel do-burring method, the reversal flow resistance method, under different machining loads and abrasive types. The final do-burring results show the validity of our punching do-burring system pursuing the burr-free punched elements.

• Journal of Korean Ophthalmic Optics Society
• /
• v.12 no.1
• /
• pp.41-51
• /
• 2007

Differential equations and their solutions were formulated to describe the deflection of the tapered, nonuniform thickness and width's temple, clamped at one end while the perpendicular force is acting on the other end which is freely suspended. The model was derived based on laws of continuity at every point inside the elastic medium that the deflection, tangent slope, bending moment, shearing force must be continuous within the medium. The model is found to be in good agreement with measurements on the beta titanium temple with the correlation 0.992 and p=0.999(Chi test). Therefore it is possible to predict the effect of various temple parameters such as elastic modulus, thickness, width on the deflection of the temples being considered.

• Journal of Biosystems Engineering
• /
• v.19 no.1
• /
• pp.17-21
• /
• 1994

This reasearch was performed to provide the fundamental intonation for the mechanization of Korean pine cone harvest when the shoot shearing method is adopted. Shear force and stress of pine cone shoots were measured and analyzed for this purpose. Samples are selected along their harvesting time and tested in 17 levels of shoot diameter from 10 to 26mm with 1mm increment. 1) Shear force-deformation characteristics showed that shoot reached its rupture point after 2 to 4 of bio-yield points. It was supposed that these multiple bio-yield points were caused by the discrete compression of wood parts which are composed of water, nutrient, resin, etc. 2) Required shear force to shear shoot was proportional to the square of shoot diamter, however, shear force for shoots of early harvesting time(Aug. 31) was proportional to the shoot diameter. Variance of shear force was increased as the harvesting time was delayed. Shear forces were distributed from 468N(Aug. 31, 12mm dia) to 4153N(Aug. 31, 26mm dia) disregarding the sampling date. 3) The average shear stresses by sampling dates were 744,822, and 883N/m2, respectively, and for the earlier shoot samples shear stress was quite smaller than the others. Shear stress was proportional to shoot diameter squared, and the effect of shoot diameter on the shear stress was decreased as harvesting time was delayed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.6
• /
• pp.84-91
• /
• 1999

The goal of this study is to analyse the stress and the strain occurring within the work piece at the fine-blanking process and hence to assume the size direction and a distribution chart of the shearing stress as the penetration of the punch is being increased trough the application of the FEM. For this analysis we introduced the piece-wise linear method in the non linear structural analysis program for large deformation sheet metal forming and we defined it as the problem of the non linear contact. Therefore we modeled the above problems as quadratic-nodded axi-symmetrical elements for the character-istics of the work piece. From the result of this analysis it was found that the shearing stress is a great deal occurred on the surface of the work piece during the beginning process of the punch penetration and it's effect is expected to influence importantly for the formation of burnish because the deeper is the penetration of the punch in the narrow clearance zone. the greater is the degree of the strain stress.

• Korea-Australia Rheology Journal
• /
• v.15 no.2
• /
• pp.55-61
• /
• 2003

The steady shear flow properties of vaseline generally used as a base of the pharmaceutical dosage forms were studied in the consideration of wall slip phenomenon. The purpose of this study was to show that how slip may affect the experimental steady-state flow curves of semisolid ointment bases and to discuss the ways to eliminate (or minimize) wall slip effect in a rotational rheometer. Using both a strain-controlled ARES rheometer and a stress-controlled AR1000 rheometer, the steady shear flow behavior was investigated with various experimental conditions ; the surface roughness, sample preparation, plate diameter, gap size, shearing time, and loading methods were varied. A stress-controlled rheometer was suitable for investigating the flow behavior of semisolid ointment bases which show severe wall slip effects. In the conditions of parallel plates attached with sand paper, treated sample, smaller diameter fixture, larger gap size, shorter shearing time, and normal force control loading method, the wall slip effects could be minimized. A critical shear stress for the onset of slip was extended to above 10,000 dyne/$\textrm{cm}^2$. The wall slip effects could not be perfectly eliminated by any experimental conditions. However, the slip was delayed to higher value of shear stress by selecting proper fixture properties and experimental conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.1
• /
• pp.74-81
• /
• 1987

The orthogonal cutting method of the nodular graphite cast iron in the lathe turning, whose structure were formulated under two kinds of annealing conditions, has been experimentally studied and the results investigated. The various characteristics of machinabilities of the nodular cast iron, depending upon its structure, have been obtained from the results as follows. (1) As depth of cut increases, the shearing strain decreases and tend gradually to increase with increase of ferrite matrix. (2) As depth of cut increases, the shearing stress slightly decreases for P$_{1}$, but it tends to increase for both of P$_{2}$ and P$_{3}$ under the same condition. The annealing effect in the process of light cutting was found to be greater than heavy cutting. (3) The cutting energy slightly decreases with the increassing of the depth of cut, and the effect of decreasing the cutting energy by the annealing is higer the light cutting than the heavy cutting. (4) The cutting equations as follow. P$_{1}$ : 2.phi.+1.58(.betha.-alpha.)=92 deg. P$_{2}$ : 2.phi.+1.40(.betha.-alpha.)=84 deg. P$_{3}$ : 2.phi.+1.37(.betha.-alpha.)=82 deg. (5) The machining constants for P$_{1}$, P$_{2}$ and P$_{3}$ which are the test-pieces in this study and classified according to the containing quantity of ferrite matrix given respectively in 78deg., 70 deg., and 68 deg. From these it can be known that the machining constants slightly decreases with increasing of the quantity of ferrite matrix contained in the nodular graphite cast iron.

• Journal of Korean Port Research
• /
• v.14 no.1
• /
• pp.87-95
• /
• 2000

This stability of a plate structure is very crucial problem which results in wrinkle and buckling. In this study, the effect of the pattern of spot-welding points of the two rectangular plates on the compressive and shear buckling load is studied with respect to the thickness, aspect ratio of plates and number of welding spots. Buckling coefficient of the plate not welded was compared with that of two plates with various thickness to extract the effect of thickness. The effect of number of welding spots are studied in two directions, longitudinal and transverse directions. The conclusions obtained were that the reinforcement effect was maximized when the aspect ratio was close to 1.75 at compressive load condition and that the effect of number of welding spots in transverse direction was larger than that in longitudinal direction at shearing load condition.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 1999.10a
• /
• pp.265-272
• /
• 1999

This stability of a plate structure is very crucial problem which results in wrinkle and bucking. In this study, the effect of the pattern of spot-welding points of the two rectangular plates on the compressive and shear bucking load is studied with respect to the thickness, aspect ratio of plates and number of welding spots. Buckling coefficient of the plate not welded was compared with that of two plates with various thickness to extract the effect of thickness. The effect of number of welding spots are studied in two directions, longitudinal and transverse directions. The conclusions obtained were that the reinforcement effect was maximized when the aspect ratio was close to 1.75 at compressive load condition and that the effect of number of welding spots in transverse direction was larger than that in longitudinal direction at shearing load condition.