• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1256-1256
• /
• 2001

The physico-chemical and texture characteristics of meat determine the nutritional, technological and sensory quality. However, the analysis of meat quality requires expensive, laborious and time consuming analytical methods. The objective of this study was to evaluate NIR spectroscopy using transmittance for determining the moisture, fat, protein and total pigment content, the water holding capacity (WHC) and the toughness of beef meat. A total of 318 spectra were recorded from ground beef samples by a Feed Analyzer 1265 of Infratec. The samples were obtained from the Longissimus muscle of the 10$^{th}$ rib of yearling bulls, ground with an electrical chopper, vacuum packaged, aged during 7 days and frozen at -24$^{\circ}C$ until the analyses were done. Moisture content was measured by oven drying at 10$0^{\circ}C$, fat content was determined by Soxhlet extraction and protein content was estimated from nitrogen content using the Kjeldahl analysis. The total pigment content was determined by the method of Hornsey and the WHC using the method of filter paper press. The instrumental evaluation of texture (maximum load WB, maximum stress MS and toughness) was conducted in an Instron equipment with a Warner-Bratzler shearing device. This analysis was performed on a chop of 3.5 cm obtained from the longissimus of the 8$^{th}$ rib, aged during 7 days, kept frozen at -24$^{\circ}C$ and cooked before the analysis. Near infrared spectra were recorded as log 1/T (T=transmittance) at 2 nm intervals from 850 to 1050 nm using a Feed Analyzer 1265 of Infratec. Calibrations were performed with the WinISI software (vs. 1.02) using the MPLS method. To examine the effect of scatter correction o. derivation of spectra on the calibration performance, calibrations were calculated with the crude spectra or pretreated with different mathematical treatments (inverse MSC, SNVD) and/or second derivative operation. For chemical composition, the use of the scatter corrections improved the calibration statistics, in terms of lower SECV and higher $r^2$. In most of the variables, the use of the 2$^{nd}$ derivative improved the predictions, mainly when combined with the SNVD treatment. However, for predicting the texture traits, the best estimation was obtained from the crude spectrum. These results showed that the equations obtained for predicting moisture, fat and total pigments were very accurate, with $r^2$ being higher that 0.9. However, the prediction of the texture traits (WB, MS, toughness) from ground meat was poor.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.15-24
• /
• 2001

In order to evaluate undrained shear strength of clayey soils using Piezocone Penetration Test (CPTu), piezoncone factor is utilized. Commonly, piezoncone factors determined by empirical basis were preferred, which were established by correlation between measurements of piezocone test and undrained strengths obtained from other shearing tests. However, previous studies on the empirical piezocone factors were site-specific and there have been no systematic investigations on the effect of both engineering characteristics of clayey soils and soil non-homogeneity on the piezocone factor. Accordingly, the direct application of the previous results to Korean clayey soils without verification may be inappropriate. In this study, empirical piezocone factors are evaluated by comparing 46 CPTu results of 10 test sites with undrained shear strength obtained from Field Vane Test (FVT) and laboratory triaxial tests. Their reliabilities are investigated by the comparison with the previous piezocone factors and the deviation of data distribution from the mean values. And the effects of referencing test methods and typical engineering characteristics of clayey soils such as overconsolidation ratio (OCR) and plastic Index (I$_{p}$) are examined. Because piezocone factors obtained for various soil conditions are widely distributed, it is not appropriate to use the mean value as a representative. Instead, it is recommended to apply the piezocone factors with OCR, which is found to be a major factor in deriving piezocone factor. The necessitated piezocone factors are presented.d.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.3
• /
• pp.416-420
• /
• 2009

An experiment of one-year duration was conducted on sixteen adult male German Angora rabbits under sub-temperate Himalayan conditions, to assess the effect of seasons on their body weight, wool production and quality, plane of nutrition and the digestibilities of nutrients. The daily meteorological attribute viz. minimum and maximum temperature; relative humidity and rainfall were recorded during winter (October to March), summer (April to June) and rainy (July to September) seasons. Biological parameters viz. body weight at the time of shearing, wool yield of individual rabbit, quality attributes of wool, fortnightly dry matter intake, chemical composition of feed and fodder and digestibilities of nutrients were recorded. Average minimum and maximum ambient temperature during winter, summer and rainy seasons were 4.6${\pm}$1.9 and 21.4${\pm}$2.8; 13.6${\pm}$2 and 30.3${\pm}$2; and 20.0${\pm}$1.4 and $31.0{\pm}1.8^{\circ}C$, respectively. The average relative humidity and total rainfall during winter, summer and rainy season were 69.5${\pm}$2.9% and 74.7${\pm}$21.8 mm; 58.6${\pm}$2.2% and 38.1${\pm}$18.1 mm; and 69${\pm}$4.2% and 104.0${\pm}$43.7 mm, respectively. The body weight of rabbits increased during all seasons, however, the maximum average daily weight gain of 3.47${\pm}$0.1 g was observed during the rainy season. The wool yield differed significantly (p$\leq$0.05) among different seasons with highest (140.4${\pm}$10 g) and lowest (108.5${\pm}$6.9 g) during winter and summer, respectively. The wool yield during the rainy season was 123.3${\pm}$5.2 g. The wool quality attributes revealed non-significant differences for staple length, fiber diameter, medulation percent, percent pure fibers and percent guard hairs. Plane of nutrition revealed significant (p$\leq$0.05) differences for concentrate intake. The concentrate intake was highest during winter (124.4${\pm}$2.6 g) followed by summer (86.8${\pm}$8.9 g) and rainy (80.7${\pm}$11.8 g) seasons. The reverse trend was observed in roughage intake with significantly (p${\leq}$0.05) lower intake during winter and highest during summer months. As a result total dry matter intake during different seasons was similar. Significant differences (p${\leq}$0.05) were observed for digestibilities of crude protein, crude fiber, ether extract, acid detergent fiber and cellulose. Digestibility of crude protein was highest during winter whereas the digestibilities of crude fiber, ether extract, acid detergent fiber and cellulose remained higher during the rainy season. During the winter season, the dry matter used for producing 100 g of wool was substantially lower than during other seasons and was concluded to be the best season for production of Angora wool under subtemperate Himalayan conditions.

• Korean Journal of Food Science and Technology
• /
• v.31 no.4
• /
• pp.1011-1016
• /
• 1999

This study was performed to search a physical method having high yield and quality and minimum environmental pollution for extraction of pectin from apple pomace. Based on the physical solubilization of plant cell wall under the condition of high temperature, pressure and shearing stress, apple pomace was treated by a corotating intermeshing type twin-screw extruder with the diameter-to-length ratio of 1/20. The specific mechanical energy of extruder was introduced as system parameter for extrusion process modeling and the shaft speed, feed rate and moisture content as process variables. The yield, average molecular weight and galacturonic acid content of water-soluble polysaccharides obtained by extrusion were, respectively, modeled with the linear functions of the system parameter which was of the form as a linear function of process variables. The specific mechanical energy increased with increase of shaft speed and with decrease of feed rate and moisture content. Out of process variables, moisture content had the greatest effect on specific mechanical energy. The yield increased with increase of specific mechanical energy while the average molecular weight and galacturonic acid content increased with its decrease. In aspects of yield and quality of pectin, the results from this study showed the possibility to replace a traditional acidic method with the extrusion treatment of this study.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.2 no.4
• /
• pp.1-9
• /
• 1982

Variation of soil properties is studied by permeating injection of chemical grouts, such as cement type, water-glass type and acrylamide type, to the same soil samples with different densities. Moreover, injection tests using specially prepared equipments of 1.0 shot system and 1. 5 shot system are attempted to investigate permeating injection effects in highly compacted soil and in the presence of ground water. The main factor which causes the improvement of cut-off effect and shearing strength is the cohesion of soil. The strength in the loose state is fundamentally governed by the membrane cohesion, meanwhile, in the loose state is governed by the structural cohesion. Injection effects under the ground water flow is considerably decreased, and effective gelling ratio of approximate 45~80% is observed by variation of velocity and gel time, besides grading of injection materials has high relation with permeation and traveling length but has little relation with effective gelling ratio. Permeating injection effects, such as gelling scope, gelling strength in highly compaoted soil conditions can be confirmed by penetration resistance diagram and iso-strength curve.

• Proceedings of the KACD Conference
• /
• 2001.11a
• /
• pp.577-577
• /
• 2001

The lastest concepts in bonding are "total etch", in which both enamel and dentin are etched with an acid to remove the smear layers, and "wet dentin" in which the dentin is not blown dry but left moist before application of the bonding primer. Ideally, the application of a bonding agent to tooth structure should be insensitive to minor contamination from oral fluids. Clinically contaminations such as saliva, gingival fluid, blood and handpiece lubricant are often encountered by dentists during preparation of a restoration. The aim of this study was to evaluate the effect of contamination by hem-ostatic agents on shear bond strength of compomer restorations. One hundred and ten extracted human maxillary and mandibular molar teeth were collected. The teeth were cleaned from soft tissue remnant and debris and stored in physiologic solution until they were used. Small flat area on dentin of the buccal surface were wet ground serially with 400, 800 and 1200 abrasive paper on automatic polishing machine. The teeth were randomly divided into 11 groups. Each group was conditioned as follows: Group 1 : Dentin surface was not etched and not contaminated by hemostatic agents. Group2 : Dentin surface was not etched but was contaminated by Astringedent (Ultradent product Inc., Utah, U.S.A.). Group3 : Dentin surface was not etched but was contaminated by Bosmin (Jeil Phann, Korea.). Group4 : Dentin surface was not etched but was contaminated by Epri-dent (Epr Industries, NJ, U.S.A.). Group5: Dentin surface was etched and not contaminated by hemostatic agents. Group 6 : Dentin surface was etched and contaminated by Astringedent. Group7 : Dentin surface was etched and contaminated by Bosmin. Group8 : Dentin surface was etched and contaminated by Epri-dent. Group9 : Dentin surface was contaminated by Astringedent. The contaminated surface was rinsed by water and dried by compressed air. Group10 : Dentin surface was contaminated by Bosmin. The contaminated surface was rinsed by water aud dried by compresfed air. Group 11 : Dentin surface was contaminated by Epri-dent. The contaminated surface was rinsed by water and dried by compresfed air. After surface conditioning, F2000 was applicated on the conditoned dentin surface. The teeth were thermocycled in distilled water at $5^{\circ}C\;and\;55^{\circ}C$ for 1000 cycles. The samples were placed on the binder with the bonded compomer-dentin interface parallel to the lmife-edge shearing rod of the Universal testing machine(Zwick 020, Germany) running at a cross head speed of 1.0mmimin. There were no significant differences in shear bond strength between groups 1 and group 3 and 4, but group 2 showed significant decrease in shear bond strength compared with group 1. There were no significant differences in shear bond strength between group 5 and group 7 and 8, but group 6 showed significant decrease in shear bond strength compared with group 5. There were no significant differences in shear bond strength between group 5 and group 9, 10 and 11.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.2
• /
• pp.98-102
• /
• 2009

Various physical properties of soils were investigated in the areas where organic farming had been practiced widely, for upland fields. The investigations were also conducted in the nearby fields under conventional to find out the influence of organic farming on the physical properties of soils. The investigated properties involved bulk density, hardness, shearing resistance, friction resistance, sinking depth of small rectangular board, water stable aggregates and the depth of soil available to plants. By and large, the practice of organic farming tended to improve all of the physical properties soils, investigated in upland soils. However, in case of water stable soil aggregates in upland soils, the reverse was previous data; in those soils water stable soil aggregates were less under organic farming. It was suspected that this might be due to intensive application of the organic materials with high C/N ratio like wood chips and wood bark. The contents of OM, Av. P2O5, and Ex. cations were higher in organic farming than those of nearby fields under conventional, due to heavy organic matter application. From the results, It could be concluded that soils under organic farming were looser and softer than those under conventional as shown by lower bulk density and hardness, but that the effect of organic farming on water stable aggregates were low.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.1
• /
• pp.5-13
• /
• 2013

Soils around a pile are highly constrained when the vertical load is applied to the pile. However, the conventional direct shear test cannot evaluate the shear strength of the soils under the normal confinement condition. The goal of this study is to evaluate the shear behaviors according to the normal displacement confinement condition including free normal displacement (FND) and constrained normal displacement (CND) during direct shearing. Jumunjin sands were prepared at the different relative densities and loaded at the different normal stresses. The specimens were sheared according to the normal confinement conditions. Experimental results show that shear strengths obtained by the CND tests are higher than those obtained by the FND tests. In addition, for the constrained normal displacement condition, the increment of shear strength increases with the increase of relative density, while the increment of shear strength decreases with the initial normal stress. This study suggests that the effect of confinement condition on the shear strength should be considered when the stability of constrained soils is analyzed.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.151-161
• /
• 2017

A TSL (Thin Spray-on Liner) has a higher initial strength and faster construction time than conventional cementitious shotcrete. Because of its high adhesion and tensile strength, the TSL reinforced concrete show a characteristic like composite materials. In this study, to consider an application to the conventional design method, ASD (allowable stress design), numerical study was used. In the numerical analysis, material and contact properties were adopt from previous studies. Then a thickness of concrete in the tunnel was evaluated with the TSL reinforced case by the ASD concept. In other words, bending compressive stress, bending tensile stress and shearing force of the concrete were considered to determine a thickness of concrete lining by the given boundary conditions. From the numerical analysis, there was no tendency to show by the ASD because the ASD is based on the elastic theory while the TSL typically contributes to reinforcement after yielding.

• Geotechnical Engineering
• /
• v.10 no.3
• /
• pp.55-78
• /
• 1994

Decomposed granite soil is a Granitic Gneiss, and it is a c Korean peninsula. It is known a changed significantly when it is aim of this study is to evaluat utility of the constitutive laws. Firstly, triaxial tests were pe sites prepared by the laborato scrutinized the characteristics results were analysed and the p evaluated. Finally, the predicted Even though the origins of slight difference in the angle of pression line( A) : both soils show In the effective mean normal uniqueness of the Normal Compr The relationships between the the decomposed granite soil tier OCR is larger than 2, the stress stress(MDS) or. even thous moved below the theoretical Ros was found to coincide with the (NC) soils, the pore pressure parameter, A,, increased up to 1.3. This phenomenon might be mainly due to the effect of the particle crushing during shearing, When the OCR value approaches 7, the negative pore pressure is developed in undrained tests and the dilatancy is observed in drained tests. The predicted and the observed behavior of drained tests showed relatively good fitting with the Cam-Clay model.