• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.5
• /
• pp.584-595
• /
• 1998

An investigation was carried out to determine experimentally the thermal conductivities of non-Newtonian fluids in a shear field. Both time independent purely viscous and viscoelastic fluids were considered. A coaxial cylinder apparatus with a rotating outer cylinder was used to establish the velocity field in the test fluid. First, the thermal conductivity of distilled water measured to validate the instrument. The experimental water data agreed within 1% of literature values and there was no effect of outer cylinder rotation (shear field). However, for non-Newtonian fluids such as aqueous CMC and Separan solutions, there were significant increases in thermal conductivities of up to 70% for CMC and 50% for Separan depending on the shear rate, polymer concentration and temperature. Considering the shear rate dependent thermal conductivity in the study of heat transfer in non-Newtonian fluids could be important. As in natural convection, the momentum and energy equations could no longer be solved separately but would have to be solved simultaneously.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.52-56
• /
• 2006

Punching tools like an electrodes are made by milling or etching or EDM. These methods had time consuming, low efficiency and air pollution. So, we have developed a shearing device which counter punching method for burrless cutting of micro wire. Using the straightened SUS304 wire with $200{\mu}m$ diameter, we confirmed the tendency of the shear plane for punch tools. It was impossible to completely remove the bun in the shearing process. In order to minimize the burr size and fine shear plane, we have accomplished the various experiment conditions such as the U-groove, the effect of the counter punch, shear angle and clearance. The results of the experiments show that indentation, slip plane and bent shape were related to the shear angle and clearance.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.1003-1008
• /
• 2001

It is recently reported that bond failure can be initiated in the region where maximum bending moment and shear force is acted by accompanying shear deformation after flexural crack in full-scale RC beams strengthened by CFRP. Such a shear deformation effect causing bond failure is relatively little in the case of small-scale specimens. So, additional reinforcing details to the critical beam section where maximum moment and shear were acted is required to prevent the bond failure caused by the shear deformations. The U-type wrapping methods by CFRP to the critical beam section is proposed and tested in this paper. Also, the applicability of design bond strength derived from the tests of small-scale beam was investigated by the full-scale RC beam strengthened by CFRP.

• Journal of the Korean Society of Safety
• /
• v.21 no.3 s.75
• /
• pp.81-86
• /
• 2006

The purpose of this study is to examine the effect of column spacing and beam size on the lateral displacement and shear lag phenomenon in bundled tube system. According to the parametric study in which the spacing of columns, the size of columns and girders in bundled tube were selected as a parameter, it is the most efficient to increase the size of the interior columns with the largest reduction of lateral drift if the steel tonnage of a frame can be increased. It was noticed that the shear lag was affected more by the exterior stiffness factor and ratio than by the interior ones when column spacing was changed, and when the size of column was changed, the reverse phenomenon was happened. And The change of column spacing affected shear lag, lateral drift, and tonnage more than that of column size or girder size.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.626-631
• /
• 2007

MR(Magneto-rheological) fluid is smart material that can be changed viscosity by controlling the magnetic field. MR damper with MR fluid can control damping force. It can be used extensively many engineering structures for reducing the effect of dynamic external disturbances. There are three kinds of MR dampers, such as valve mode, direct-shear mode and squeeze mode. In this study, design process of direct-shear mode MR damper with the MR fluid gap was developed. The parameters that used in the direct-shear mode MR damper Informed from the experiment of valve mode MR damper of Lord company. Magnetic analysis with finite element method was performed to find the optimal annular gap.

• Structural Engineering and Mechanics
• /
• v.62 no.3
• /
• pp.311-324
• /
• 2017

In this paper a new eight-unknown higher order shear deformation theory is proposed for functionally graded (FG) material plates. The theory based on full twelve-unknown higher order shear deformation theory, simultaneously satisfy zeros transverse stresses at top and bottom surface of FG plates. Equations of motion are derived from principle of virtual displacement. Exact closed-form solutions are obtained for simply supported rectangular FG plates under uniform loading. The accuracy of present numerical results has been verified by comparing it with generalized shear deformation theory. The effect of power law index of functionally graded material, side-to-thickness ratio, and aspect ratio on static behavior of FG plates is investigated.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.187-194
• /
• 1999

Laminated rubber bearings are widely used as a key component in seismic isolation of structural systems subjected to earthquake loadings. The combination of rubber layers and reinforcing steel shims makes the bearings conditionally unstable similar to buckling of ordinary columns. The shear flexibility of these short columns can lead to relatively low buckling Toads which may be further reduced when high shear strains are simultaneously imposed As an analytical approach, the area reduction formula has been proposed to account for the reduction in buckling load due to shear, but the degree of conservatism is unknown. In order to complement analytical approaches, a non-linear finite element analysis can be used. In this paper, a numerical study which aims at determining the effect of high shear strain on the critical load of elastomeric bearings is presented. From the load-displacement curve at each specified shear displacement, the buckling load can be obtained using the Southwell procedures. The results obtained are then compared against the theoretical predictions in order to examine the validity and the conservatism of the theoretical formulas.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.129-132
• /
• 2005

The primary purpose of this investigation is to find out the shear behavior and the shear capacity of RC bare frames, brick-infilled RC frames, and damper-retrofitted RC frames and to evaluate the average shear strength of brick--infill wall. The main variables art the absence of brick infill wall and steel plate slit damper. The test results show that the shear capacity of specimen IF-DR is 2.8 times as high as that of the specimen BF and it presents the fact that the retrofitting effect and the possibility of RC frame reuse with changing the slit damper is verified. And the average shear strength of the brick infill wall is figured to be at $5.0 kgf/cm^2$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.259-262
• /
• 2005

This paper deals with the shear strengthening effect of RC beams strengthened with carbon fiber sheets. Fifteen strengthened RC beams(including control beam) were experimentally evaluated to determine improvements in shear strength. The major parmeters of experiment variables are fiber sheet strengthening ratios and strengthening methods of fiber sheet(I-S, I-W, U-S, U-W type). Reinforced concrete beams strengthened with carbon fiber sheets were tested under the combined control of load. Considering strengthening ratios and strengthening methods of fiber sheet, shear capacity and failure mode of test specimens were evaluated. The results show that shear capacity of beams strengthened with fiber sheet is about $28.82\%$ in IS type, $20.49\%$ in IW type, $26.04\%$ in US type, $28.70\%$ in UW type higher than the strength of control beam.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.797-801
• /
• 2003

The mechanical properties such as shear strength and the hardness of milli-size products that manufactured for various process parameters by forward extrusion using square dies are investigated. Shear strength test is implemented for the observation of relation between vickers hardness and shear strength in the interface of head and shaft part of a stepped pin. When the extrusion ratios of pure aluminum and pure copper billets increase, the hardness on both the surface and the center line of a pin also increase, especially the hardness on the surface is shown to be a little higher than on the center. The existence of knock-out pad in extrusion die caused hardness increase in the interface of a extruded pin. As compared shear strength with hardness of a pin, the approximated linear relations are suggested in this study.