• Journal of Welding and Joining
• /
• v.17 no.2
• /
• pp.66-75
• /
• 1999

Weld bead quality in tailored blank(TB) is critically affected by edge preparation of sheets. The edge quality of prepared sheets for TB can be classified into straightness and the cross section quality of sheared plane such as a ratio of shear face, shear plane angle, etc. In order to have a good edg quality for butt-welding sheets, precision shearing will be recommended. In this paper, the feasibility of a conventional mechanical shearing as the edge preparation for tailored blanks is studyied. It reveals that fine shearing may not be the unique solution as it is generally accepted. To obtain the good shearing condition with a conventional mechanical shearing, experiments were carried out using Tahuchi method. The major parameters affecting a sheared contour are the clearance between upper blade and lower blade, and shear angle. The optimal shearing condition yields a very good straightness along the entire length of the cut, which gives a butt joint gap less than 10% of the base material thickness. The good cross section of sheared plane is also achieved in the optimal shearing condition such as a ratio of the shear face above 65%, a cross section's shear plane angle above 85%, little burr, which is providing finally good weld beads.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.3
• /
• pp.23-32
• /
• 2010

In this study, Generally sandbag was used to reinforce slope or restore levee by using the in-situ material. To increase shear strength of sandbag, the Velcro system was effective for geosynthetic interface and make up for the weakness of shear strength between sandbag to sandbag. In this study, shear properties of geosynthetic-geosynthetic and geosynthetic-soil were evaluated from large scale direct shear tests. The cohesion and the angle of internal friction of each interface was evaluated. And laboratory model tests were performed to compare strength of reinforcement with strength of none reinforcement. As a result of this study, the cohesion and the angle of internal friction of each interface was increased, especially the cohesion was increased more than the angle of internal friction. Also according to the result of model test, the bearing capacity was increased by 20%.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.8
• /
• pp.65-73
• /
• 2012

Soil-rock interface, mainly founded in Granite region of Korea, is known as one of the important factor of the slope failure at the rainfall due to smaller shear strength than soil itself. However, research of the effect on slope stability by soil-rock interfaces is insufficient. Therefore, a series of direct shear tests were performed in order to investigate the effect of soil-rock interface on slope stability. The method of tests is to get sand itself and sand-artificial rock interface shear strength from different grain size of sands and artificial rock samples. The results of tests show that the friction angle of interface depends primarily on particle size and surface roughness. Interface friction angle ratio ${\mu}(={\delta}/{\Phi})$ is in the range of 0.75 ~ 0.96, this results indicate that interface friction angle is smaller than sand itself.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.179-184
• /
• 2005

Shear strength parameters obtained from filed survey are important factors in the analysis of slope stability. In this study, sensitivity analysis was performed to evaluate the effect of input parameters on the analysis of slope stability. The input parameters selected for sensitivity analysis were slope angle, cohesion, and friction angle. Monte-Carlo Simulation method was used for calculating input parameters and the factor of safety was computed by means of limit equilibrium method. A rock slope, which has failed in the field, was used for the sensitivity analysis in the analysis of slope stability. The result of analysis shows that the factor of safety of the rock slope was a little low. From partial correlation coefficient(PPC) of input parameters determined from the sensitivity analysis, slope stability was dependant on cohesion and slope angle. The effect of friction angle was lower than that of cohesion and slope angle on slope stability.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.4
• /
• pp.105-112
• /
• 2009

In this study, a series of direct shear tests were performed to investigate the characteristics of friction angles for sands and interface friction angle between sands and construction materials with respect to different relative density of the Nak-dong River sands and shearing velocity. The result of the test shows that friction angles of sands are always higher than interface friction angle between sands and construction materials. As the shearing velocity get faster, the friction angles of sand became higher. With respect to the density of sand by reducing void ratio, friction angles increase linearly, and relevant equations were proposed to calculate the friction angle by changing void ratio and relative density of sand. The interface roughness of construction materials was also an important factor in interface friction angle.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.52-56
• /
• 2006

Punching tools like an electrodes are made by milling or etching or EDM. These methods had time consuming, low efficiency and air pollution. So, we have developed a shearing device which counter punching method for burrless cutting of micro wire. Using the straightened SUS304 wire with $200{\mu}m$ diameter, we confirmed the tendency of the shear plane for punch tools. It was impossible to completely remove the bun in the shearing process. In order to minimize the burr size and fine shear plane, we have accomplished the various experiment conditions such as the U-groove, the effect of the counter punch, shear angle and clearance. The results of the experiments show that indentation, slip plane and bent shape were related to the shear angle and clearance.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.57.2-57.2
• /
• 2011

In this study, the effects of shear flows around a 2-dimensional airfoil, S809 on its aerodynamic characteristics were analyzed by CFD simulations. Various parameters including reference inflow velocity, shear rate, angle of attack, and cord length of the airfoil were examined. From the simulation results, several important characteristics were found. Shear rate in a flow makes some changes in the lift coefficient depending on its sign and magnitude but angle of attack does not have a distinguishable influence. Cord length and reference inflow also cause proportional and inversely proportional changes in lift coefficient, respectively. We adopted an analytic expression for the lift coefficient from the thin airfoil theory and proposed a modified form applicable to the traditional load analysis procedure based on the blade element momentum theory. Some preliminary results applied to an well known load simulation software, FAST, are presented.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.813-818
• /
• 2009

Shear properties of plastic bottle film/plastic bottle film and plastic bottle film/granitic soil which were evaluated from static friction tests. The monotonic shear experiments were performed by using an tilt table apparatus and large direct shear device. The test results showed that the friction angle of each interface and the interface depended on the amount of normal stress, the type of the interface used. Therefore, the testing method should be determined carefully by considering the type of loads and normal stress expected in the field with using the materials installed in the site.

• Journal of the Korea Concrete Institute
• /
• v.13 no.2
• /
• pp.130-138
• /
• 2001

This paper presents on the shear behavior prediction of reinforced concrete beams using Transformation Angle Truss Model (TATM). The TATM can evaluate the stress-strain relationships for cracked concrete by transforming stresses and strains for principal plane into those over the crack surfaces. This proposed analytical method simplifies the Fixed Angle Softened Truss Model (FA-STM) and removes the limitation of applicability of the FA-STM. The shear.strength and strain of reinforced concrete beams are predicted by using the TATM. For the verification of proposed method, experimental results of reinforced concrete beams were compared with theoretical results by the TATM, FA-STM and Rotating Angle Softened Truss Model (RA-STM).

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.1
• /
• pp.49-55
• /
• 2007

In order to utilize treads of waste tire as reinforcement material it is necessary to know the interface friction angle between tread surfaces and soil and tensile strength of connection joint of tire treads. In this research large direct shear tests were performed to get the interface friction angle between the inner and outer surfaces of treads and soil for different degree of compaction. From the large direct shear tests, the ratio of interface friction angle to the shear friction angle of sand, ${\delta}/{\phi}$, were 1.06 in outside surface of tire tread and 0.93 in inside surface of tire tread. For weathered granite soil the ratio of interface friction angle was 0.98 and 0.92 for outside and inside of tread, respectively. Also tensile tests were performed using universal testing machine for the connection joint of treads and Tirecell units using bolts. The tensile strength of connection joint increased with the number of bolts and with the sizes of washers. Connection by polypropylene ropes showed lower strength than those of bolts.