• Journal of the Korean Society of Safety
• /
• v.31 no.6
• /
• pp.93-98
• /
• 2016

This study analyzed the inflow characteristics of debris flow according to shape of defensive structure and computed risk index. In order to simulate debris flow, two shapes of defensive structure were considered. Initial mass distribution was set with a rectangular shape and defensive structures were set semi-circular shape and rectangular shape, respectively. It was found that a defensive structure with semicircular shape was more vulnerable to debris impact compared with rectangular shape because the flow mass became concentrated in quadrant part of the inner circle. If the velocity of the debris flow was less than 1 m/s, the risk assessment by FII (Flood Intensity Index) was much appropriate. However, when the movement of debris runout was faster than 1 m/s, the risk index of FHR (Flood Hazard Rating) provided improved classification due to its subdivided hazardous range.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.19 no.5
• /
• pp.842-852
• /
• 1995

The purpose of this study was to provide fundamental data of characterizing for age group of obese women's body shape. The subjects were 132 obese women, age of 20~59. The criteria of obestity based on Vervaeck index ($\geq$92.3), Rohrer index ($\geq$ 1.6), and bust girth ($\geq$90 cm). Thirty eight measurement items were used for F-test. Forty two transformed variables (including 4 additional variables) were used for cluster analysis The results were as follows: 1. Characteristics for age group were described that 20's was narrow shoulder, flesh contoured shape in upper body. 30's was rounded upper back, 40's was the slightest fatty shape, and 50's was the fattest round shape among four age groups. 2. Four types of obese women's body shape were classified by cluster analysis. Body shape of type 1 was fatty abdomen, and rounded upper back in 50's mainly. Body shape of type 2 was slightly fatty. Body shape of type 3 was round shape. Body shape of type 4 was the smallest girth in the obese women in 40's mainly.

• The KSFM Journal of Fluid Machinery
• /
• v.1 no.1 s.1
• /
• pp.81-89
• /
• 1998

In this study, the effects of the impeller shapes on the pump performances of the non-clogging and the screw-type centrifugal pumps are experimentally studied. The characteristics of total head, efficiency and power of the non-clogging pump increase as the number of vanes increases. The screw-type centrifugal pump with the linear-shape vane shows a little better performance than that of the screw-type centrifugal pump with the curved-shape vane. The differences in the characteristics of total head, efficiency and power are, however, insignificant. Therefore, it is advisable that, considering the convenience of pump manufacturing, the screw-type centrifugal pump with the linear-shape vane should be used. This study also compares the pump characteristics of the non-clogging pump and screw-type centrifugal pump. The characteristics of total head and efficiency of the non-clogging pump are better than those of the screw-type centrifugal pump. The screw-type centrifugal pump requires more shaft power than the non-clogging pump.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.723-726
• /
• 2002

In the recent years, as the research and the development of micro and precision machinery become active, the interest of micro actuators using SMA(Shape Memory Alloy) has been increased. The dynamic characteristic analysis of SMA is necessary for actuator application and many common researches report the material characteristics of SMA sufficiently. However, the research of dynamic characteristics is very deficient. In this paper, the helical spring is fabricated with NiTi SMA wire of high resistivity The farce, response speed, temperature, and displacement are measured by digital force gauge, infrared thermometer, and laser displacement sensor so that the dynamic characteristics of this SMA actuator is analyzed.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.276-281
• /
• 2006

The fractal dimension is quantitatively to define the irregular characteristic of the shape in natural. It can be useful in describing morphological characteristics of various wear particles. This paper was undertaken to diagnose failure condition for sliding members in lubrication by fractal dimension. It will be possible to diagnose wear mechanism, friction and damage state of machines through analysis of shape characteristics for wear particle on driving condition by fractal parameters. In this study, the calculating and analyzing methods of fractal dimensions were constructed for the condition monitoring and wear particle analysis in lubricant condition. So, we carried out the Friction and wear test with the ball on disk type tester, and the fractal parameters of wear particle in lubricated conditions were calculated. Fractal parameters were defined as texture fractal dimension ($D_{t}$), structure fractal dimension ($D_{s}$) and total fractal dimension (D).

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.9
• /
• pp.903-909
• /
• 2012

In elliptical vibration cutting(EVC) where the cutting tool traces a micro-scale 2-dimensional elliptical trajectory, the kinematical and vibrational characteristics of the EVC device greatly affect cutting performance. In this study, kinematical and vibrational characteristics of an EVC device constructed with two orthogonally-arranged stacked piezoelectric actuators were investigated both analytically and experimentally. The step voltage was applied to the orthogonal EVC device and the associated displacements of the cutting tool were measured to assess kinematical characteristics of the orthogonal EVC device. To investigate the vibrational characteristic of the orthogonal EVC, sinusoidal voltage was applied to the EVC device and the resulting displacements were measured. It was found from experiments that coupling of displacements in the thrust and cutting directions and the tilt of the major axis of the elliptical trajectory exists. In addition, as the excitation frequency is in vicinity of resonant frequencies the distortion in the shape of the elliptical trajectory becomes greater and change in the rotation direction occurs. To correct the shape distortion of the elliptical trajectory, the shape correcting procedure developed for the parallel EVC device was applied for the orthogonal EVC device and it was shown that the shape correcting method successfully corrects distortion.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2533-2542
• /
• 1994

This paper suggests a simple approach to determining the screw characteristics for a three0dimensional flow in a channel with a finite aspect ratio(ratio of a width to a depth, W/H) by introducing a Total Shape Factor($F_t$) to correct a two-dimensional flow analysis for a channel with an infinite aspect ratio. In the present study, the Total Shape Factor($F_t$) was defined as a ratio of a net flow rate obtained by the three-dimensional analysis to that by the two-dimensional analysis. In the proposed approach, the quantity, $ \frac{{\partial}F_t}{\partial(H/W)}$ turns out to be almost constant and to play an important role in understanding the effects of the flights. Therefore, $ \frac{{\partial}F_t}{\partial(H/W)}$ are extensively reported in this paper in terms of several dimensionless parameters. This simple approach with such database will be very useful for extruder designers to predict the screw characteristics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.9
• /
• pp.76-83
• /
• 2021

This study examines the characteristics of spraying conditions based on the change in standoff distance during fine particle spraying while measuring the surface roughness, maximum depth, and maximum width of the sprayed surface. The processing shape of the sprayed surface is analyzed to understand the effects of injection pressure, nozzle diameter, standoff distance, processing shape, processing cycle, processing speed, and injection particles, which are the main factors of fine particle injection processing. Based on the derived characteristics, we attempt to determine the interrelationships of these major factors. The standoff distance is set as a variable factor and a spray machining experiment using a hexagonal shape (from among polygons) instead of square and circular shapes is conducted. Results reveal that research on the characteristics of spraying conditions could be expanded based on changes in the shapes of workpieces.

• Smart Structures and Systems
• /
• v.30 no.2
• /
• pp.183-193
• /
• 2022

Structural health monitoring and structural vibration control are multidisciplinary and frontier research directions of civil engineering. As intelligent materials that integrate sensing and actuation capabilities, shape memory alloys (SMAs) exhibit multiple excellent characteristics, such as shape memory effect, superelasticity, corrosion resistance, fatigue resistance, and high energy density. Moreover, SMAs possess excellent resistance sensing properties and large deformation ability. Superfine NiTi SMA wires have potential applications in structural health monitoring and micro-drive system. In this study, the mechanical properties and electrical resistance sensing characteristics of superfine NiTi SMA wires were experimentally investigated. The mechanical parameters such as residual strain, hysteretic energy, secant stiffness, and equivalent damping ratio were analyzed at different training strain amplitudes and numbers of loading-unloading cycles. The results demonstrate that the detwinning process shortened with increasing training amplitude, while austenitic mechanical properties were not affected. In addition, superfine SMA wires showed good strain-resistance linear correlation, and the loading rate had little effect on their mechanical properties and electrical resistance sensing characteristics. This study aims to provide an experimental basis for the application of superfine SMA wires in engineering.

• The Research Journal of the Costume Culture
• /
• v.23 no.4
• /
• pp.726-736
• /
• 2015

The apparel industry has recently been recognizing the important target market of middle-aged women. The aim of this study was to examine the anthropometric characteristics of US women of 46 to 65 years of age and identify distinctive body shape characteristics of US middle-aged women. A total of 1915 middle-aged women whose ages ranged from 46 to 65 were selected from the SizeUSA database. The age range was divided into two groups: 46-55 and 56-65. Twenty-four body measurements important for apparel development were chosen. Four factors-Girth Factor, Height Factor, Hip Drop Factor, and Bust Drop Factor-accounted for the US middle-aged women's body measurements. The body shapes were classified into four body shapes, which were Y-Shape in the overweight range, S-Shape in the overweight range, H-Shape in the overweight range, and the A-Shape in obese range. H-Shape, which was the least-defined waist in relation to the bust and hips with a short height, existed more in older middle-aged women than in younger middle-aged women. Y-Shape, S-Shape, and A-Shape existed more in the group of younger middle-aged women than in the group of older middle-aged women. In addition, compared with the younger middle-aged women, older middle-aged women had narrower shoulders, a larger waist, thinner legs, and a longer distance between side neck to bust point. The findings from the current study may be applied in the apparel industry for developing clothing sizing systems for US middle-aged women.