• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2003년도 학술발표논문집
• /
• pp.459-462
• /
• 2003

This study aimed at proposing the optimum design of stilling basins in dam spillways by analyzing hydraulic characteristics for various positions and shapes of end sills through the hydraulic model test. The performance of energy dissipating in the case of vertical shape of end sill was much better than the case of inclined shape. Moreover, we could confirm that no further improvement in hydraulic characteristics at stilling basin as well as downstream of the river were made if the height of end sill was increased up EL 50m, e.g., the proposed design value by computation.

• Smart Structures and Systems
• /
• 제4권2호
• /
• pp.261-278
• /
• 2008

The results of the application of shape memory alloy (SMA) prestressing devices on an aqueduct are presented in this paper. The aqueduct was built in 1747 to provide water to the city of Larnaca and to its port. Because of its importance to the cultural heritage of Cyprus, the aqueduct has been selected as one of the case-study monuments in the project Wide-Range Non-Intrusive devices toward Conservation of Historical Monuments in the Mediterranean Area (WIND-CHIME). The Department of Antiquities of Cyprus, acting in a pioneering way, have given their permission to apply the devices in order to investigate their effectiveness in providing protection to the monument against probable catastrophic effects of earthquake excitation. The dynamic characteristics of the structure were determined in two separate occasions and computational models were developed that matched very closely the dynamic characteristics of the structure. In this paper the experimental setup and the measured changes in the dynamic characteristics of the monument after the application of the SMA devices are described.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.746-752
• /
• 2000

A study on discharge characteristics of a rotating discharge hole is very important to enhance the performance of an induction motor which have external forced cooling system. The discharge characteristics of rotating discharge holes are influenced by rotating speed, length-to-diameter ratio, inlet shape of rotor holes, etc. An experimental study on the effect of chamfered inlet edge of rotor inlet part with various depth-to-diameter and inlet chamfered edge angle is conducted. Depth-to-diameter ratios range from 0 to 0.5 and inlet chamfered edge angle range from 0 to 60. As a result, there is an optimal design point of inlet chamfered edge depth. And the inlet edge angle far maximum discharge coefficient is influenced mainly by the rotating speed of discharge holes.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.491-492
• /
• 2006

In the microstereolithography which can make 3-D microstructures, curing depth is different according to exposure energy. Curing depth has to be controlled to fabricate complex 3-D microstructures with overhang shape. It becomes increases when the exposure energy increases. And photocurable resin is cured when the exposure energy is bigger than critical energy. So optimal exposure energy has to be found to fabricate overhang structures without being gel. To make thinner layer, UV absorber is used and exposure pattern is changed. In this paper, we find curing characteristics according to exposure energy, and fabricate microstructures with overhang shape.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.11-18
• /
• 2001

To clarify the influence of SAC shape of hole-type diesel nozzle on injection characteristics and spray patterns, the injection rate of three nozzle types(standard SAC nozzle, Needle-cut VCO nozzle and VCO nozzle) were measured by Zeuch's method and pictures of the sprays were taken by CCD camera. As the pump speed became higher, the injection characteristics of the three nozzles were different. Injection rate and perssure curves at the high pressure pipe in Needle-cut VCO nozzle were much more similar to the VCO nozzle than those of the SAC nozzle. When the needle was at pre-lift period for all speeds, the spray of the Needle-cut VCO nozzle showed almost the same shape as the SAC type nozzle. There was no differense in spray pattern at the needle full-lift periods.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2010년 춘계학술발표회 논문집
• /
• pp.5-6
• /
• 2010

Needs for the methodology of segmentation of linear feature according to the shape characteristics of line feature are increasing in cartographic linear generalization. In this study, the line segmentation method using expansible moving window is presented. This method analyzes the generalization effect of line simplification algorithms depend on the line characters of linear feature and extracts the sections which show exclusively low positional error due to a specific algorithm. The description measurements of these segments are calculated and the target line data are segmented based on the measurements. For segmenting the linear feature to a homogeneous section, expansible moving window is applied. This segmentation method is expected to be used in the cartographic map generalization considering the shape characteristics of linear feature.

• Nuclear Engineering and Technology
• /
• 제36권4호
• /
• pp.364-373
• /
• 2004

This study investigates the fluidelastic instability characteristics of helical steam generator type tubes used in operating nuclear power plants. To obtain a natural frequency, corresponding mode shape, and participation factor, modal analyses using various conditions are performed for helical type tubes. Investigated are the effects of the number of turns, the number of supports, and the status of the inner fluid on the modal and fluidelastic instability characteristics of the tubes, which are expressed in terms of the natural frequency, the corresponding mode shape, and the stability ratio.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(4)
• /
• pp.145-148
• /
• 2002

A study on image searching and management techniques is actively developed by user requirements for multimedia information that are existing as images, audios, texts data from various information processing devices. We had been studied an automatical shape region segmentation method using color. distribution and edge characteristics of moving images for. contents-base description. The Proposed method uses a color information quantized on human visual system and extracts overlapped regions to be matched by using edge characteristics of the image frame. The performance of the proposed method is represented by similarity for comparison to a segmented image and original image.

• 드라이브 ㆍ 컨트롤
• /
• 제12권1호
• /
• pp.21-27
• /
• 2015

Pneumatic cylinders are classified into rod-type pneumatic cylinders and rodless pneumatic cylinders depending on the presence of the rod. Rodless cylinders have a constant area and have no deflection. Rodless cylinders are widely used in automatic systems requiring high-speed performance and high-precision transportation. However, the research of the pneumatic cylinder has been focused on the structure and life characteristics. In this research, aging characteristics and shape parameter analysis which are related to the lifetime were investigated. By conducting the lifetime tests with two different materials for the transfer plate, the failure mode and lifetime characteristics were analyzed. By the Anderson-Darling (A-D) verification based on the complete data set, the analysis results of lifetime distribution, shape parameter, and scale parameter were provided.

• Current Optics and Photonics
• /
• 제3권5호
• /
• pp.429-437
• /
• 2019

Temperature adaptability is an important metric for evaluating the performance of an optical system. The temperature characteristics of the optical system are closely related to the material and shape of its lens. In this paper, we establish a mathematical model relating the temperature characteristics to the shape and material of the lens. Then a novel assembly structure that can solve the lens constraint and positioning problem is proposed. From those basics, the correctness of the theoretical model and the effectiveness of the assembly structure are verified through simulated analysis of the imaging quality of the optical system, whose operating temperature range is $-60{\sim}100^{\circ}C$.