• 한국항공우주학회지
• /
• 제40권2호
• /
• pp.139-145
• /
• 2012

천음속 영역에 적합하도록 개발된 수정 Sonic Arc 익형의 저속 공력특성에 대해 조사하였다. 이 익형은 Schwendenman이 제안한 sonic arc 형상 함수와 NACA0012 형상 data 그리고 상용 프로그램 Maple을 이용하여 설계하였다. 수정 Sonic Arc 익형의 저속공력 특성을 조사하기 위해 마하수 0.3 이하에서 수치해석을 수행하고 그 결과를 NACA0012 익형의 저속 공력성능과 비교분석하였다. 각 마하수에서 수정 sonic arc 익형의 항력은 NACA0012의 항력보다 약 1.5% 정도 작게 나타났으며, 양력 비교에서도 수정 Sonic Arc 익형의 양력은 NACA0012의 양력보다 약 2% 정도 일정하게 작게 나타났다. 또한 각 마하수에서 수정 Sonic Arc 익형의 모멘트 계수는 NACA0012의 값보다 약 1.4% 정도 작게 나타났다.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2003년도 춘계학술논문발표회논문집
• /
• pp.164-170
• /
• 2003

In this paper, we studied on the firing characteristics and electrical fire analysis of power cord deteriorated by thermal stress. The cross section of PVC insulating cord deteriorated by indirect flame decreased through heat convection. PVC insulating cord deteriorated by direct flame was bumpy shape. The exothermic peak of normal cord was shown at ($526.7^{\circ}C$), but the peaks or on(heat treatment temperature) ($150^{\circ}C$) cord was shown at ($299.6^{\circ}C$) and [$502.2^{\circ}C$]. The exothermic peaks according to high temperature were similar to those of amorphous carbon. In the FT-IR analysis, the absorption peak of normal cord indicated double bond of oxygen and carbon in benzene ring at 1720.0$cm^{1}$. As the HTT was high, the height of characteristic peak decreased and the peak of carbonyl group was shown at about 1625.7$cm^{-1}$. The characteristic peak of single bond(O-H) was shown at about 3479.2$cm^{-1}$. In case of the internal part of wire covering deteriorated by over current, the characteristic peak were shown at about 3417.3$cm^{-1}$ and 1600.2$cm^{-1}$. The above results show that we can distinguish the differences according to the fire pattern through the internalㆍexternal analysis of wire covering deteriorated by heat.

• 한국가구학회지
• /
• 제16권2호
• /
• pp.49-57
• /
• 2005

This study purposed to grasp the Design Characteristic of the representative Furnitures produced recently by Domestic Furniture Manufacturers. As for the researching method, setting as the object of the selected 7 furniture manufacturers, through the regional classification such as living room, bedroom, dining room, and then chose again the 395 items of furnitures to be analyzed. The Design Characteristic of the chosen furnitures has been examined clearly by the analysis standard framework for those peculiarities at view of aesthetic, decorating and material. As the result of analysis, as for the aesthetic Peculiarity of the furnitures, the rectilinear form was overwhelming than the curve lined shape, and it was appeared that the brighter tone of color was used quite more. In the respect of aesthetic characteristic, the furnitures decorated with modern style is pretty gaining predominance than that of reflected style of traditional character, and since modern residential space has been maintained continuously as minimal shaped trend for several years, it could be known that such moulding and decorating peculiarities and also furniture as the composing factor of space had been selected together with it. Based on such conclusion, standing on this time point where the design trend of residential space is being changed, it is also considered that the Development of Furniture Design which copes positively with such change tendency in the future.

• 수면정신생리
• /
• 제8권1호
• /
• pp.67-71
• /
• 2001

Independent Component Analysis (ICA) is a blind source separation method using unsupervised learning and mutual information theory created in the late eighties and developed in the nineties. It has already succeeded in separating eye movement artifacts from human scalp EEG recording. Several characteristic sleep waves such as sleep spindle, K-complex, and positive occipital sharp transient of sleep (POSTS) can be recorded during sleep EEG recording. They are used as stage determining factors of sleep staging and might be reflections of unknown neural sources during sleep. We applied the ICA method to sleep EEG for sleep waves separation. Eighteen channel scalp longitudinal bipolar montage was used for the EEG recording. With the sampling rate of 256Hz, digital EEG data were converted into 18 by n matrix which was used as a original data matrix X. Independent source matrix U (18 by n) was obtained by independent component analysis method ($U=W{\timex}X$, where W is an 18 by 18 matrix obtained by ICA procedures). ICA was applied to the original EEG containing sleep spindle, K-complex, and POSTS. Among the 18 independent components, those containing characteristic shape of sleep waves could be identified. Each independent component was reconstructed into original montage by the product of inverse matrix of W (inv(W)) and U. The reconstructed EEG might be a separation of sleep waves without other components of original EEG matrix X. This result (might) demonstrates that characteristic sleep waves may be separated from original EEG of unknown mixed neural origins by the Independent Component Analysis (ICA) method.

• 펄프종이기술
• /
• 제43권1호
• /
• pp.57-64
• /
• 2011

The purpose of this research is to investigate the anatomical and chemical properties of arrowroots for the use of paper fibers. The cells consisting of arrowroots showed certain affinities with those in the fibers and vessels of hardwood. Its parenchyma cells showed different shapes with those of hardwood. It was observed that starch was filled in the multi-shape cells. The average width and length of arrowroot fibers were $15.2{\mu}m$ ($11.1-20.3{\mu}m$) and 1.9 mm (1.49 mm-2.31 mm), respectively. In the chemical characteristics of arrowroots, the contents of cold- and hot-water, alcohol-benzene, and alkali extractives were 12-17%, 15.6%, and 38.8%, respectively. Its chemical composition was 61.3% holocellulose, 15.5% lignin and 2.0% ash.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.654-656
• /
• 2002

The pole shape. turn-on angle. and turn-off angle are important design factors that largely influence Switched Reluctance Motor' s performance when designing a switched reluctance motor. These design factors must be considered simultaneously because an independent factor restricts the improvement of the switched reluctance motor' s performance. After performing the analysis using nonlinear same characteristic finite element method that contains a operating circuit, the influence upon the torque characteristics was analyzed by the pole shape and the angles. This paper presents the most suitable design value according to input conditions and various speeds. Especially.the most suitable angles were derived from the voltage equation. and an effective design range is showed from the angles.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.693-696
• /
• 2011

The SRM (Switched Reluctance Motor) is composed of silicon steel plates where the rotor structure is simple and laminated without coil winding or permanent magnet, making it mechanically robust and its maintenance and repair excellent. Applying SRM as traction motor for railway vehicle is given consideration because of its ruggedness capability in severe loading condition and its compact structure. Optimal design of SRM is needed to reduce torque ripple to apply SRM for railway traction drive because SRM has high torque ripple. In this paper, switched reluctance motor with three different stator pole shapes is taken for magnetic analysis using 3d finite element method to apply SRM as traction drive for railway vehicle. It is observed that the model 3 added Tooth Tang Depth and Slot Round to stator shape gives the improved inductance and torque characteristic.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.264-268
• /
• 2003

Recently reduction of industrial products in size and weight has been increased by application of micro-drills in gadgets of high precision and a great interest of a micro-drilling has been raised. Due to the lack of tool stiffness and the chip packing, the micro-drilling requires not only the robust tool structure which has not affected by vibration but also effective drilling methods designed to prevent tool fracture from cutting troubles. This paper presents an optimum design shape of a 0.15 mm micro-drill associated with a new manufacturing process to improve the production rate and to lengthen the tool life and suggestions on the micro-drilling characteristic properties associated with the tool life and workpiece quality.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.172-175
• /
• 2002

This paper presents perceptual model with a stochastic rnultiresolution characteristic that can be applied with watermark embedding in the biorthogonal wavelet domain. The perceptual model with adaptive watermarking algorithm embed at the texture and edge region for more strongly embedded watermark by the SSQ(successive subband quantization). The watermark embedding is based on the computation of a NVF(noise visibility function) that have local image properties. This method uses non-stationary Gaussian model stationary Generalized Gaussian model because watermark has noise properties. In order to determine the optimal NVF, we consider the watermark as noise. The particularities of embedding in the stationary GG model use shape parameter and variance of each subband regions in multiresolution. To estimate the shape parameter, we use a moment matching method. Non-stationary Gaussian model use the local mean and variance of each subband. The experiment results of simulation were found to be excellent invisibility and robustness. Experiments of such distortion are executed by Stirmark benchmark test.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.825-828
• /
• 2005

In this paper, we propose a new nonvolatile unit memory cell and proposal peripheral circuit using the polymer material. Memory that relies on bistable behavior- having tow states associated with different resistances at the same applied voltage - has attracted much interest because of its nonvolatile properties. Such memory may also have other merits, including simplicity of structure and manufacturing, and the small size of memory cells. We have plotted the load line graphs for the use of a polymer memory character, hence we have designed in the band-gap reference shape of a write/erase drive, and then designed in the 2-stage differential amplifier shape of a sense amplifier in the consideration of a low current characteristic of a polymer memory cell. The simulation result shows that is has high gain about 80dB by sensing the very small current.