• 설비공학논문집
• /
• 제9권3호
• /
• pp.343-353
• /
• 1997

This paper presents a theoretical model for predicting transient behaviors during storage process of the cool storage system using the R141b clathrate. Introduction of the lumped capacitance method along with a brine reservoir having large thermal capacity yields a set of simplified energy equations. Based on the Arrhenius equation and the known experimental findings, the formation rate of clathrate for which the degree of subcooling is properly accounted is newly developed. An effective nondimensionalization of the model equations facilitates the closure of modeling as well as parametric study. Calculated results for a specific case not only simulate a typical pattern of temperautre variation in the tank successfully, but also agree reasonably well with available data. The effect of each characteristic parameter on the system performance is also investigated. It is revealed that the dominant among relevant parameters are the activation energy of reaction, the degree of subcoling and the initial mass fraction of refrigerant. Finally, the uncertainty associated with modeling of the shaft work variation appears to need further studies.

• 환경위생공학
• /
• 제21권2호
• /
• pp.11-19
• /
• 2006

Ran numerical analysis about simplicity warm current model (simple turbulence model) to examine closely distributed laying stress on NOx of contaminant that happen in downtown that building is massed and result is as following. Downtown building is massed and transfer of vehicles can know that frequent area receives greatly effect of building. Pollution displays class kind phenomenon striking in the building, class kind done pollution that show high density being mixed with pollution that happen in vehicles being flowed in again side know can. Divide velocity vector of pollution and density change to ancient city and did numerical analysis. Because NOx is flowed in diversion of water neighborhood by continuous this kind in Godo 20m point, density showed density of $0.0907mg/m^3s$, and can know that Banryuhyeon that Pollution strikes in the building at ancient city 30m point is decreased and approaches with freedom flowing without cooperation (cavity) phenomenon remarkably. Because pollution strikes in the building at distance shaft 383m point, class kind do phenomenon that know appeared notedly Nopeungeonmulgwanat between building pollution density $0.067mg/m^3$ head of a families high appear.

• 한국지반공학회논문집
• /
• 제21권2호
• /
• pp.85-91
• /
• 2005

본 논문에서는 실내모형실험 및 유한요소 프로그램인 CRISP을 이용하여 사질토 지반에 근입되어있는 선단지지 말뚝의 하중-침하(P-S) 관계를 규명하였다. 선단지지말뚝의 효과를 유한요소 해석에서 모사하기 위하여 몇 가지 형태의 인터페이스 요소들(slip elements)을 말뚝 주변 및 선단에 도입하였다. 비관련 소성흐름 법칙의 정도, 즉 지반강도 정수인 내부마찰각과 팽창각의 차이 정도를 고려한 Mo-Coulomb 지반 모델에 있어서, 인터페이스 요소들이 포함된 선단지지말뚝은 내부마찰각과 팽창각의 차이가 유한요소 해의 수렴에 매우 중요한 역할을 하는 것으로 나타났다. 한편, 이와는 대조적으로 말뚝 주변에 적용한 인터페이스 요소 대신 Roller로 모사된 선단지지말뚝의 유한요소 해는 비관련 소성흐름 법칙의 정도에 대해서 영향을 받지 않고 수렴되는 것으로 나타났다.

• Journal of Electrical Engineering and Technology
• /
• 제8권3호
• /
• pp.530-543
• /
• 2013

This paper describes a control scheme of speed sensorless fuzzy direct torque control (FDTC) of permanent magnet synchronous motor for electric vehicle (EV). Electric vehicle requires fast torque response and high efficiency of the drive. Speed sensorless FDTC In-wheel PMSM drives without mechanical speed sensors at the motor shaft have the attractions of low cost, quick response and high reliability in electric vehicle application. This paper presents a new approach to estimate the speed of in-wheel electrical vehicles based on Model Reference Adaptive System (MRAS). The direct torque control suffers in low speeds due to the effect of changes in stator resistance on the flux measurements. To improve the system performance at low speeds, a PI-fuzzy resistance estimator is proposed to eliminate the error due to changes in stator resistance. High performance sensorless drive of the in-wheel motor based on MRAS with on line stator resistance tuning is established for four motorized wheels electric vehicle and the whole system is simulated by matalb/simulink. The simulation results show the effectiveness of the new control strategy. This proposed control strategy is extensively used in electric vehicle application.

• 한국기계가공학회지
• /
• 제12권1호
• /
• pp.52-62
• /
• 2013

In order to obtain the relation between the cutting force and the process parameters in the chamfering process for the gear of a gear shaft, analysis of the process was performed with a simplified model instead of considering the whole actual 3-dimensional cutting situation produced between cutting tool and gear. The model divided the actual situation into the accumulation of hundreds of 2-dimensional layers with a small thickness in the direction of the height of gear and derived cutting force at a cutting position by accumulating each cutting force calculated in a layer. With proposed method to analyze the cutting forces in the chamfering process, it was revealed that the cutting position and size were exactly searched to calculate the cutting force in each layer. The total cutting force was the highest in the corner where the cutter encountered the gear first during the relative motion between them. The cutting forces were changed in proportion to the cutting parameters such as feed rate and trajectory.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.191-198
• /
• 2015

In this study, the flow characteristics at the ventilation holes was analyzed by using numerical method when carbon composite brake disk was rotated at a constant speed. In order to ensure the validity of the analysis results, grid dependency test was performed by considering the accuracy and appropriateness, and 4mm mesh size was selected for decrease of the maximum error rate 63.6%. As a result, the outside air flows in the clearance between the disk and shaft in case of B model. whereas, the outside air flows in the clearance or the outlet of the ventilation holes in case of A and C models. And also average static pressure at the outlet was changed depending on shape of the ventilation holes and rotational speed of the disk in case of A and C models. Besides, in the B model, intake air according to the clearance goes with side surface of ventilation hole, and so increased by mean velocity of 4.64m/s and mean pressure of 0.58pa in the ventilation hole outlet, in case of disk rotational speed of 146.21rad/s.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.48-53
• /
• 2011

In this study, it is to verify the applicability for a simplified model(IEC61400-2, Design Require-ments for Small Wind Turbines, 2006-03) is the international standard is used to the structural design. In the design process of a wind turbine, the safety of a designed wind turbine is one of the most important factors. The simplified model can be used to determine the design load for small wind turbines. So, this paper has been re-evaluated a small wind turbine design loads that produced already. As a result, the material characteristic value(Rchar) of Blade, Rotor shaft and the tower are $90E6[N/m^2]$, $441E6[N/m^2]$ and $94E6[N/m^2]$. Therefore, the value of the applied safety factor to each part of the survival probability of 95% are satisfied.

• 동력기계공학회지
• /
• 제12권1호
• /
• pp.41-46
• /
• 2008

The primary objective of this study is to truly understand exciting forces of the in-line 4 cylinders engine. Exciting forces of the engine apply a source of the vehicle NVH(Noise, Vibration, Harshness). To understand exciting forces, first was governed theoretical equations for single cylinder engine. And this theoretical equations was programming using MATLAB software. To compare theoretical analysis value, was applied MSC.ADAMS software. To determined the specification of engine(2,000cc, in-line 4) was applied ADAMS/Engine module. And this specification for engine was applied ADAMS/View and MATLAB software. The geometry model for ADAMS/View analysis was produced by the 3-D design modeling software. After imported 3-D model, each rigid body was jointed suitable. Under idle speed for engine, was analysed. The results of analysis are fairly well agreed with those of three analysis method. Using MATLAB software proposed in this study, engine exciting fores can be predicted. Also using ADAMS/Engine module and ADAMS/View software, engine exciting forces can be predicted.

• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1141-1149
• /
• 1992

본 연구에서는 Davison이 제안한 견실 제어이론을 응용하여, 자기베어링에 의 해서 지지되는 로터계를 위한 중앙 집중식 서보제어기를 설계하였다. 삼각함수 형태 의 외란과 지령치에 대한 완벽한 영향회피와 추적을 위하여, 일반적 서보보상기(serv- ocompensator)를 MIMO 제어기에 내장하였다. 또한, 상기 제어기의 일부분(subset)으 로서, 중앙집중식 PID 제어기를 제안하였다. 제2장에 자기베어링에 의해 지지되는 강체 로터계의 동적 모델을 요약하였으며, 제3장에서 제어기법의 구축을 설명하고, 두 가지 형태의 제어기에 대한 성능 비교와 견실성의 한계를 보여주는 시뮬레이션 결과를 제 4장에 제시하였다.

• 한국음향학회지
• /
• 제38권3호
• /
• pp.328-333
• /
• 2019

본 논문은 선박 추진기의 캐비테이션 침식현상을 연구하기 위하여 추진기에서 발생하는 소음과 캐비테이션 격렬도의 연관성에 대하여 분석하였다. 캐비테이션 침식은 캐비테이션 붕괴의 빈도와 강도로 정의 할 수 있는 '캐비테이션 격렬도'와 밀접히 연관되어 있다. 캐비테이션 붕괴에 의해서 발생하는 압력파는 다양한 진폭과 지속시간의 연속적인 펄스의 형태로 나타나며 이를 캐비테이션 거동과 동조 분석하여 캐비테이션 붕괴에 따른 추진기 소음 연관성을 파악하였다. 이 기법을 경사축 추진기시험을 활용하여 추진기침식시험에 대한 정량적 평가방안을 제시하였다.