• Journal of Korean Tunnelling and Underground Space Association
• /
• v.4 no.3
• /
• pp.207-216
• /
• 2002

Conventional Korean tunnel portals require a lot of overburden. For stability reasons, about 1.5 to 2.0 times the tunnel diameter is needed for the height in order to achieve a sufficient arching effect. Thus, considerable movement of earth and support constructions are required which lead to undesirably large changes of and damage to the environment. With a massively designed pipe roof, tunnels at low overburden can be built. To effectively construct pipe roof as an advanced safeguarding method, the following properties are indispensable: stability, insensitivity to settling and drilling accuracy. A new pipe roof method, AT-casing system, has been developed which on the one hand entirely combines the properties mentioned above, and which on the other hand permits the construction of safe, economical and environmentally friendly tunnels at low overburden heights of 3 to 5m.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1134-1138
• /
• 2008

Electret filter media are used in general ventilation filters, disposable respirators, vehicle cabin filters, vacuum cleaners and room air cleaners. There are basic mechanisms of interception, inertial impaction, diffusion, gravitational settling, electrostatic attraction by which an aerosol particle can be deposited onto a fiber in a filter. The ability of fine particle removal strongly depends on the electrostatic forces between particles and polarized fibers. Thus, the stability of the fiber polarization is a major factor in the reliability of electret filters. In this study, electrical properties and filtration performance of electrospun filter media are quantitatively investigated. Electrical properties of electrospun filters have been studied on surface charge potential and surface charge density. Also the filtration performance of the electret filters are evaluated on collection efficiency. Electrospun filters show same collection efficiency with low pressure drop compare to commercialized HEPA filters. Surface charge potential and surface charge density of electrospun filters are increased with increasing applied voltage. Also collection efficiency of electrospun filters is increased with increasing surface charge potential and surface charge density.

• Journal of Energy Engineering
• /
• v.24 no.2
• /
• pp.144-153
• /
• 2015

At low temperature, Wax build-up and settling can affect adversely the cold weather performance of the diesel vehicle. In this study, we test the cold properties of diesel by blending ratio of biodiesel, kerosene and WAFI. Also, we test the cold weather performance for diesel vehicle by fuel cold properties. Cold properties of diesel are improved by adding the WAFI, kerosene and get worse by adding the biodiesel. WAFI is effective to improve a cold filter plugging point(CFPP) and Kerosene is effective to improve a cloud point(CP). CFPP and pour point(PP) are related to cold weather performance of diesel vehicle but CP is unrelated. CFPP indicate a limit temperature of vehicle driving possibility.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.938-946
• /
• 2008

This study is on sealing leakage holes where are in landfills to make clay cakes with clay particles, which have a negative surface charge using the method of electrophoresis. Generally, electrophoresis is the motion of charged particles in a colloid under the influence of an electric field; particles with a positive charge go to the cathode and negative to the anode. In this study in order to develop the prevention system of leakages of the leachate in landfills, one-dimensional electrophoresis tests were conducted for determining the properties of the motion of the electrophoresis and cutoff using the method of electrophoresis depending on various the effect factors such as types of clays, concentrations of the clays, and applied electric field. In case of the experiments of determining the optimum clays, Na and Ca-Bentonite, Na and Ca-Montmorillonite, which have greater zeta-potential, cation, exchange capacity as well as ability of cutoff, and Micro-cement inducing cementation were chosen and then the effect of those clays was investigated. Moreover, the properties of the motion and settling of the clays were investigated following electric field varied from 0 to 1V/cm at different concentration of the clays in order to determine both the properties of the motion of the clays and the efficiency of electric field when applying different direct current. Ultimately, the ability of cutoff was examined through measuring the permeability of the clay cakes derived from the one-dimensional electrophoresis tests.

• Applied Chemistry for Engineering
• /
• v.1 no.1
• /
• pp.63-72
• /
• 1990

Surface of crystalline silica was sequentially reacted with silane(A 187), liquid rubber(CTBNx8) and vinyl monomer(AA, MMA, 2-HEA, GMA) in existance of amines(TEA, CTMAB, BETAC) or peroxide(BPO). By mixing it with epoxy resin at a ratio 0~36%(volume %) of total component, liquid properties of mixtures was investigated experimentally. i) Coating ratio depended on quantity and sorts of catalyst. ii) Total coating of 2.5~5.8% was attained by using 0.1~2.0% of catalyst. iii) Treated surfaces represented each different features in according to sorts of treatment. iv) Silane/rubber or silane/rubber/vinyl represented lower viscosity and settling than non-treated or silane-treated.

• Environmental Engineering Research
• /
• v.12 no.1
• /
• pp.21-29
• /
• 2007

For this study, we polymerized polyacrylamide base flocculants (PAA) and tested their properties and settling efficiency as a treatment for potable water. The most common chemicals for potable water treatment in Korea are alum or PAC. However, due to various reasons (such as rainy season or algae), inorganic flocculants cannot be solely depended on to solve all the problems caused by the poor quality of inflow water. When PAA coupled with coagulants in a potable water purification process is used, the turbidity removal efficiency increases by a factor of three on a single chemical system using PAC (Raw water: 5.21 NTU; Treated PAA+PAC: 0.34 NTU; and, Treated PAC: 1.04 NTU). It is possible to offset the toxic effect of residual monomers in treated water using PAA, because the concentrations of residual acrylamide are less than 400 mg/L in the polymer itself and less than $0.04\;{\mu}g/L$ in the treated water base at a dosage of 0.1 mg/L. Therefore, PAAs may be a workable, and dependable, potable water treatment process for the high pollutant level of resource water.

• Journal of Microbiology and Biotechnology
• /
• v.13 no.3
• /
• pp.378-384
• /
• 2003

Mesophilically-grown granular sludge seeded in thermophilic UASB reactor was monitored to better understand the start-up process of the reactor. The reactor was fed with a synthetic wastewater containing glucose. As COD loading rate increased stepwise, methane production rate increased. Maximum values of COD removal efficiency (95%) and methane production rate (5.3 l/day) were achieved by approximately day-80 and remained constant afterward. However, physicochemical and microbial properties of granules kept changing even after day-80. Specific methanogenic activity (SMA) was initially negligible, and increased continuously until day-153 and remained constant afterward, showing the maximum value of $1.51{\pm}0.13\;g\;CH_4-COD/g$ VSS/day. Deteriorated settling ability of granules recovered the initial value by day-98 and was maintained afterward, as determined by sludge volume index. Initially reduced granule size increased until day-126, reaching a plateau of 1.1 mm. Combined use of fluorescence in situ hybridization and confocal laser scanning microscopy (CLSM) allowed to localize families of Methanosaetaceae and Merhanosarcinaceae in granules with time Quantitative analyses of CLSM images of granule sections showed abundance patterns of the methanogens and numerical dominance of Methanosaeta spp. throughout the start-up period. The trend of SMA agreed well with abundance patterns of the methanogens.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.12
• /
• pp.1715-1721
• /
• 2002

Numerical analysis was conducted to characterize the gas flow field and particle deposition on a horizontal freestanding semiconductor wafer under the laminar flow field at vacuum environment. In order to calculate the properties of gas, the gas was assumed to obey the ideal gas law. The particle transport mechanisms considered were convection, Brownian diffusion and gravitational settling. The averaged particle deposition velocities and their radial distributions fnr the upper surface of the wafer were calculated from the particle concentration equation in an Eulerian frame of reference for system pressures of 1 mbar~1 atm and particle sizes of 2nm~10$^4$ nm(10 ${\mu}{\textrm}{m}$). It was observed that as the system pressure decreases, the boundary layer of gas flow becomes thicker and the deposition velocities are increased over the whole range of particle size. One thing to be noted here is that the deposition velocities are increased in the diffusion dominant particle size range with decreasing system pressure, whereas the thickness of the boundary layer is larger. This contradiction is attributed to the increase of particle mechanical mobility and the consequent increase of Brownian diffusion with decreasing the system pressure. The present numerical results showed good agreement with the results of the approximate model and the available experimental data.

• Steel and Composite Structures
• /
• v.29 no.5
• /
• pp.569-578
• /
• 2018

This paper aims to investigate the transient vibration behavior of functionally graded carbon nanotube (FG-CNT) reinforced nanocomposite plate resting on Pasternak foundation under pulse excitation. The plate is considered to be composed of matrix material and multi-walled carbon nanotubes (MWCNTs) with distribution as per the functional grading concept. The functionally graded distribution patterns in nanocomposite plate are explained more appropriately with the layer-wise variation of carbon nanotubes weight fraction in the thickness coordinate. The layers are stacked up in such a way that it yields uniform and three other types of distribution patterns. The effective material properties of each layer in nanocomposite plate are obtained by modified Halpin-Tsai model and rule of mixtures. The governing equations of an illustrative case of simply-supported nanocomposite plate resting on the Pasternak foundation are derived from third order shear deformation theory and Navier's solution technique. A converge transient response of nanocompiste plate under uniformly distributed load with triangular pulse is obtained by varying number of layer in thickness direction. The validity and accuracy of the present model is also checked by comparing the results with those available in literature for isotropic case. Then, numerical examples are presented to highlight the effects of distribution patterns, foundation stiffness, carbon nanotube parameters and plate aspect ratio on the central deflection response. The results are extended with the consideration of proportional damping in the system and found that nanocomposite plate with distribution III have minimum settling time as compared to the other distributions.

• Journal of Korean Port Research
• /
• v.12 no.1
• /
• pp.9-17
• /
• 1998

The evaluation structure of complex problems is composed of multi-attributes and hierarchy. A many studies were existed on this problems, but that based on the assumption that the evaluation elements were independent. The actual evaluation problems have the complexity, ambiguity and interlinkage among the elements. In this situation, the fuzzy evaluation process is very effective in settling the complex problems. For evaluation of large scale hierarchical MADM problem, the fuzzy evaluation algorithm is developed in this paper, and that is centering on the identification of fuzzy measures. In this study, we newly identified the weight and interaction among the evaluation attributes. The results of this study are as follows: we can identified the hierarchical structure of the evaluation problem which is composed of the evaluation structure, function and hierarchy; we improved the existed weighting method which could be accomplished by normalizing process, considering the uncertainty and new weight integrating method which come from Dempster-Shafer theory. And we take into account the interaction properties among more than 3 evaluation attributes, which can be compared with the existed studies in which only 2 evaluation attributes taked into account.