• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.151-156
• /
• 2002

Drying shrinkage cracking which may be caused by the relatively large specific surface is a matter of grave concern for latex modified concrete(LMC) overlay and rapid-setting cement latex modified concrete(RSLMC) overlay. LMC and RSLMC were studied for field applications very actively in terms of strength and durability in Korea. However, there were no considerations in drying shrinkage. Therefore, the purpose of this study was to investigate the drying shrinkage properties of LMC and RSLMC with the main experimental variables such as cement types(ordinary portland cement, rapid setting cement), latex contents(0, 5, 10, 15, 20%), W-C ratios, and curing days at a controlled environment of 60% of relative humidity and 2$0^{\circ}C$ of temperature. The drying shrinkage for specimens was measured with a digital dial gauge of Demec. The test results showed that the drying shrinkage of LMC and RSLMC were considerably lower than that of OPC and RSC, respectively. This might be attributed to the interlocking of hydrated cement and aggregates by a film of latex particles, water retention due to hydrophobic, and colloidal properties of the latexes resulting in reduced water evaporation.

• 한국건축시공학회지
• /
• 제5권3호
• /
• pp.101-107
• /
• 2005

This paper reports the contribution of Shrinkage reducing admixture(SRA) to the physical properties and drying shrinkage of concrete. Dosage of SRA is varied with. For the properties of fresh concrete, an increase in SRA dosage results in a decrease in fluidity and air content, while setting time is accelerated. For the properties of hardened concrete, the incorporation of mineral admixture leads to a decrease in compressive strength at early age, whereas after 28 days, the incorporation of fly ash(FA) and blast furnace slag(BS) has greater compressive strength than conventional concrete without admixture. The use of SRA results in a decrease in compressive strength. The incorporation of SRA with every $1\%$ increase causes the decrease of compressive strength by as much as $3\~6\%$. For drying shrinkage properties, the incorporation of FA and BS reduces drying shrinkage slightly. The use of SRA also decreases drying shrinkage. Every $1\%$ of increase in SRA dosage can reduce drying shrinkage by as much as $10\~15\%$

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.93-98
• /
• 2002

The effects of polymer-cement ratio, antifoamer content and shrinkage-reducing agent content on the air content, setting time and drying shrinkage of polymer-modified mortars using redispersible polymer powder are examined. As a result the air content of the polymer-modified mortars using redispersible polymer powder tend to decrease with increasing polymer-cement ratio and antifoamer agent content. Regardless of the antifoamer content, the setting time of the polymer-modified mortars using redispersible polymer powder tend to delayed with increasing polymer-cement ratio. Irrespective of the antifoamer content, the drying shrinkage of the polymer-modified mortars using redispersible polymer powder tend to decrease with increasing polymer-cement ratio and shrinkage-reducing agent content.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.296-299
• /
• 2004

The effects of polymer-cement ratio, antifoamer content and shrinkage-reducing agent content on the setting time and drying shrinkage of high-fluidity polymer-modified mortars using redispersible polymer powder are examined. As a result, the setting time of the high-fluidity polymer-modified mortars using redispersible polymer powder tend to delayed with increasing polymer-cement ratio, regardless of the antifoamer conten,. Irrespective of the antifoamer content, the drying shrinkage of the high-fluidity polymer-modified mortars using redispersible polymer powder tend to decrease with increasing polymer-cement ratio and shrinkage-reducing agent content.

• 콘크리트학회논문집
• /
• 제12권3호
• /
• pp.3-10
• /
• 2000

In this study, we compared a plain mortar with the CAS-system shrinkage compensation mortar for Ondol that is Korean traditional heating system. The Ondol mortar is necessary to have properties as non-crack, fine flatness and stability for thermal changes. especially, mortar'crack prevention is to be most important property in Ondol mortar. To develope the stable material on the crack-prevention, we used to calcium-sulfo-aluminate(CSA)system in shrinkage compensation mortar. And so, we confirmed the effects of calcium-sulfo-aluminate(CSA) system for mortar's physical properties such as setting time, compressive strength and expansion ratio for crack prevention. The initial and final setting time of the CSA mortar is faster than plain mortar about 2hours. And, Compressive strength increased about 20% that plain mortar. The crack length per unit area, plain mortar is 0.426∼0.481m/m2. The Results of apartment construction field test, the shrinkage compensation mortar is excellent about the crack-reduce effect.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.134-135
• /
• 2014

In this study, mock-up test for high strength concrete with ERCO has been carried to analyse the effect of autogenous shrinkage reducing of using ERCO. The following results could be made as the conclusion. Results of EIS were lower than 2.5 and showed good resistance for separation of materials. For the setting time, specimen with ERCO showed delay of setting comparing with Plain. For the autogenous shrinkage, as the generation of saponification, capillary pores inside the concrete were filled by soap and the autogenous shrinkage has been obviously decreased. It could be identified that using ERCO in high strength showed good effect on reducing autogenous shrinkage in high strength concrete.

• 대한토목학회논문집
• /
• 제32권5A호
• /
• pp.307-315
• /
• 2012

최근 국내에서도 압축강도 180 MPa, 인장강도 10 MPa 이상의 초고성능 섬유보강 콘크리트(Ultra High Performance Fiber Reinforced Concrete, UHPFRC)가 개발되었다. 그러나 UHPFRC는 물-결합재비가 낮고 다량의 고분말 혼화재료를 혼입하며, 굵은 골재를 사용하지 않기 때문에 초기 재령에서의 자기수축이 크고, 표면이 급격히 건조하는 등 기존의 일반 콘크리트(Normal Concrete, NC) 및 고성능 콘크리트(High Performance Concrete, HPC)와는 다른 재료적 특성을 보인다. 그러므로 본 연구에서는 UHPFRC에 적합한 재료 실험 방법과 규정을 제안하고 극 초기 재령에서의 강도 특성을 평가하기 위하여 응결 및 수축, 인장 실험을 수행하였다. 응결 실험 결과 파라핀 오일을 UHPFRC의 모르타르 표면에 적용할 경우 표면에서의 급격한 건조현상을 효율적으로 억제할 수 있는 것으로 나타났으며, 시멘트와 배합수의 수화반응을 지연 또는 촉진 시키지 않는 것으로 나타나 응결 실험 시 표면건조 방지제로 적합한 것으로 판단되었다. 또한, 링-테스트를 수행하여 내부 강재 링의 온도와 변형률의 경향이 달라지는 시점을 수축 응력 발현 시점으로 정의하였으며, 이를 응결 실험과 비교하여 본 결과 응결침에 걸리는 관입 저항력이 약 1.5 MPa일 때 수축 응력이 발현되는 것으로 나타났다. 이는 초결 및 종결보다 약 0.6시간, 2.1시간 빠른 것이며, 상기 시점을 UHPFRC의 자기수축 측정 시점(time-zero)으로 규정하였다. 마지막으로, 본 연구에서는 극 초기 재령 인장강도 측정 장비를 제작하여 초결시점에서부터 UHPFRC의 인장강도와 탄성계수를 측정하였으며, 이를 고려한 UHPFRC의 인장강도 및 탄성계수 예측식을 제안하였다.

• 산업기술연구
• /
• 제22권A호
• /
• pp.193-200
• /
• 2002

Drying shrinkage cracking which may be caused by the relatively large specific surface IS a matter of grave concern for latex modified concrete(LMC) overlay and rapid-setting cement latex modified concrete(RSLMC) overlay. LMC and RSLMC were studied for field applications very actively in terms of strength and durability in Korea. However, there were no considerations in drying shrinkage. Therefore, the purpose of this dissertation was to study the drying shrinkage properties of LMC and RSLMC with the main experimental variables such as cement types(ordinary portland cement, rapid setting cement), water-cement ratios and curing days at a same controlled environment of 60% of relative humidity and $20^{\circ}C$ of temperature The drying shrinkage for specimens was measured with a digital dial gauge of Demec. The test results showed that the drying shrinkage of LMC and RSLMC were considerably lower with low water-cement ratio, respectively This might be attributed to the interlocking of hydrated cement and aggregates by a film of latex particles, water retention due to hydrophobic, and colloidal properties of the latexes resulting in reduced water evaporation.

• 콘크리트학회논문집
• /
• 제24권4호
• /
• pp.491-498
• /
• 2012

이 연구는 시멘트 콘크리트 포장의 보수나 프리캐스트 제품용으로 사용되는 UP-MMA 폴리머 콘크리트의 경화수축, 열팽창계수 및 탄성계수에 대한 연구이다. 이를 위해 UP-MMA비, SRA 첨가량, 시험온도 등을 변수로 하여 경화수축 시험과 UP-MMA비에 따른 열팽창과 압축응력-변형률에 대하여 시험을 실시하였다. 그 결과 경화수축은 29.2~$82.6{\times}10^{-4}$으로 UP 비율과 시험온도에 큰 영향을 받는 것으로 나타났다. 그리고 열팽창계수는 21.6~$31.2{\times}10^{-6}/^{\circ}C$, 탄성계수는 2.8~$3.3{\times}10^4MPa$, 극한변형률은 0.00381~0.00418이었으며, 이는 UP-MMA비에 크게 영향을 받는 것으로 나타났다. 이러한 결과들은 UP-MMA 폴리머 콘크리트의 적용을 위한 설계에 중요한 기초자료로 이용될 수 있을 것이다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.27-30
• /
• 2003

This study is investigated the various properties and drying shrinkage of concrete according to water content under the condition proper fluidity is adjusted, in order to suggest the method for reduction of crack by drying shrinkage. According to the results, though water content varies, slump and air content are satisfied to the planed values, but shear slump and separation happen at water content of 120 and 140kg/$m^3$ due to the overuse of superplasticizer(SP). As water content is diminished, setting time is retarded by an increase of the using amount of SP, and compressive and tensile strength increase in the range of 160-180kg/㎥ of water content, but decrease significantly at 120 and 140kg/$m^3$. Length change by drying shrinkage decrease with a decrease of water content. Therefore, considering not only drying shrinkage but also fluidity, setting time and strength, it proves that the most appropriate water content of concrete is 160kg/$m^3$ in the condition of this experiment.