• 제목/요약/키워드: setting process monitoring

검색결과 53건 처리시간 0.022초

Identification of Electrical Resistance of Fresh State Concrete for Nondestructive Setting Process Monitoring

  • Shin, Sung Woo
    • 비파괴검사학회지
    • /
    • 제35권6호
    • /
    • pp.414-420
    • /
    • 2015
  • Concrete undergoes significant phase changes from liquid to solid states as hydration progresses. These phase changes are known as the setting process. A liquid state concrete is electrically conductive because of the presence of water and ions. However, since the conductive elements in the liquid state of concrete are consumed to produce non-conductive hydration products, the electrical conductivity of hydrating concrete decreases during the setting process. Therefore, the electrical properties of hydrating concrete can be used to monitor the setting process of concrete. In this study, a parameter identification method to estimate electrical parameters such as ohmic resistance of concrete is proposed. The effectiveness of the proposed method for monitoring the setting process of concrete is experimentally validated.

Investigation of Setting Process of Cementitious Materials Using Electromechanical Impedance of Embedded Piezoelectric Patch

  • Lee, Chang Joon;Lee, Jun Cheol;Shin, Sung Woo;Kim, Wha Jung
    • 한국건축시공학회지
    • /
    • 제12권6호
    • /
    • pp.607-614
    • /
    • 2012
  • In this study, the evolution of the electro-mechanical impedance (EMI) of a piezoelectric (PZT) patch embedded in fresh cement paste was investigated to discuss the possibility of monitoring the setting process of cement-based materials using an EMI sensing technique. A tailored thin square PZT patch was embedded in cement paste before casting, and EMI signatures of the embedded patch were continuously measured from casting up to 12 hours. A standard penetration resistance test was performed to compare and correlate the evolution of EMI during the setting process. The results showed that EMI responses differ according to the age of the cement paste, and that the behavior of the EMI resonance peak has a clear correlation with the penetration resistance of the cement paste. Based on the results, it is concluded that an EMI sensing technique using embedded PZT patch can be effectively applied to monitor the setting process of cement-based materials.

연삭 작업상태 감시 시스템 개발 (Monitoring system of the grinding working conditions)

  • 김성렬;윤덕상;김화영;안중환
    • 제어로봇시스템학회:학술대회논문집
    • /
    • 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
    • /
    • pp.387-390
    • /
    • 1997
  • Grinding process takes a long time that grinding machine is setted properly. It is difficult for user to judge correctly the abnormal states generated in grinding process. Air grinding has to be reduced for the improvement of productivity. In addition, it is important to monitor the dressing and the grinding process so that the grinding working maintains optimal grinding conditions. In this study, the monitoring system using the acoustic emission is developed to monitor these processes continuously. This system was able to reduce the preparation as well as the machine setting time in grinding operation.

  • PDF

The CV Control Chart

  • Kang, Chang-W;Lee, Man-S;Hawkins, Douglas M.
    • 한국품질경영학회:학술대회논문집
    • /
    • 한국품질경영학회 2006년도 추계 학술대회
    • /
    • pp.211-216
    • /
    • 2006
  • Monitoring variability is a vital part of modem statistical process control. The conventional Shewhart Rand S charts address the setting where the in-control process readings have a constant variance. In some settings, however, it is the coefficient of variation, rather than the variance, that should be constant. This paper develops a chart, equivalent to the S chart, for monitoring the coefficient of variation using rational groups of observations.

  • PDF

ECDIS에 의한 외끌이 기선저인망 어선의 투양망 조업 과정의 실시간 모니터링 (Real-time monitoring of net setting and hauling process in fishing operations of Danish seine vessel using ECDIS)

  • 이대재;변덕수
    • 수산해양기술연구
    • /
    • 제43권4호
    • /
    • pp.347-354
    • /
    • 2007
  • This paper describes on the real-time monitoring of net setting and hauling process for fishing operations of Danish seine vessels in the southern waters of Korea as an application of a PC based ECDIS system. Tracking of fishing process was performed for the large scale Danish seine vessel of G/T 90 and 350 PS class using the fishing gear which the length of net, ground rope, head rope and sweep line including warp in both sides were 86m, 104m, 118m and 3,200m, respectively. Tracking information for net setting and hauling process was continuously recorded for 23 fishing operations performed on November and December, 2003. All measurement data, such as trawl position, heading, towing course and past track which was individually time stamped during data acquisition, was processed in real time on the ECDIS and displayed simultaneously on the ENC chart. The results indicated that after the separation of a marker buoy from Danish seiner, the averaged running speed of vessel and the averaged setting period while shooting the seine on the course of diamond shape to surround the fish school in the 23 fishing operations were 8.3 knots and 13.1 minutes, respectively. And with the maker buoy taken on board, the averaged running speed of vessel and the averaged towing period while closing the seine on the straight route was 1.0 knots and 47.0 minutes, respectively. After the closing stage of hand rope, the hand rope was towed by the averaged speed of 2.2 knots during the 13.0 minutes. The average area for route of diamond shape swept by sweep lines of the seine in 23 fishing grounds was $709,951.6m^2$. Further investigation is also planed to provide more quantitative tracking information and to achieve more effective surveillance and control of Danish seine vessels in EEZ fishing grounds.

SS-OCT용 파장 스위핑 레이저를 위한 스위핑 중심 세팅 자동화 (Sweeping Center Setting Automation for Wavelength Swept Laser used in SS-OCT)

  • 엄진섭
    • 센서학회지
    • /
    • 제26권5호
    • /
    • pp.324-330
    • /
    • 2017
  • In this paper, the automation of sweeping center setting for wavelength swept laser used in SS-OCT has implemented. For 3 regions where the initial FFP-TF pass wavelength can be located, each different DC voltage pattern is applied to FFP-TF. Through its performance test to the laser, fast and exact setting to sweeping central wavelength, flat sweeping with ${\pm}0.5dB$ fluctuation range, and 10 mW average optical power were obtained. This shows that the realized automatic setting process can replace an inconvenient manual setting operation used for current wavelength swept laser. Additionally it cuts costs for optical spectrum analyzer necessary to laser spectrum monitoring.

SNMP를 이용한 PC 실습실 시스템의 모니터링과 제어 (Monitoring and Controlling of Systems in PC room using SNMP)

  • 안성진;정진욱
    • 컴퓨터교육학회논문지
    • /
    • 제3권1호
    • /
    • pp.109-115
    • /
    • 2000
  • 이 논문에서는 SNMP를 이용하여 윈도우 환경에서 동작하는 실습실의 PC를 관리하기 위해 MIB을 정의하고 이를 모니터링 및 제어하는 관리 시스템을 설계하였다. 제안된 시스템은 PC의 상태를 제어하는 제어 시스템과 실시간 모니터링 및 프로세스 제어를 담당하는 모니터링 시스템으로 구성된다. 제어 시스템의 경우 PC의 구성 정보 갱신 및 설정과 장애 발생시 이를 백업/복구를 담당한다. 모니터링 시스템은 초중고 생의 PC를 모니터링하고 실시간으로 실행중인 프로세스를 제어 및 새로운 작업을 실행시키는 기능을 갖고 있다. 이 시스템은 교사가 초중고의 PC 실습실에서 교육중 발생할 수 있는 학생들의 프로그램 사용을 통제하고 모니터링함으로써 교육의 효과를 높일 수 있다.

  • PDF

OES 센서를 이용한 반도체 식각 공정 모니터링 시스템 개발 (A Semiconductor Etching Process Monitoring System Development using OES Sensor)

  • 김상철
    • 한국컴퓨터정보학회논문지
    • /
    • 제18권3호
    • /
    • pp.107-118
    • /
    • 2013
  • 본 논문에서는 반도체 식각 공정 모니터링 시스템을 개발한다. 반도체 산업은 첨단 산업 중, 전자제품의 필수 부품을 생산하는 대표적인 고부가가치 산업으로, 세계 각국에서 치열한 개발 경쟁을 벌이고 있다. 이에 따라 반도체 제품의 품질과 특성, 그리고 생산성을 향상하기 위한 많은 연구들이 진행되고 있는데, 공정 모니터링 기술이 이에 해당한다. 실제로 반도체 회로를 형성하는 식각 공정에서의 불량은 큰 피해를 야기 시키므로, 공정을 상세히 모니터링 할 수 있는 시스템의 개발이 필요하다. 본 논문에서 기술하는 반도체 식각 공정 모니터링 시스템은 플라즈마를 이용한 건식식각 공정을 상세하게 관찰 분석하여 관리자에게 피드백하고, 설정된 시나리오에 맞게 자동으로 공정을 제어하여 공정 자동화 효율을 극대화한다. 실시간으로 모니터링을 수행하고 그 결과를 즉각적으로 시스템에 반영한다. 관리자는 시스템에서 제공하는UI(User Interface)를 통해 공정의 현재 상태를 진단할 수 있다. 시스템은 관리자가 사전에 작성한 공정 시나리오를 따라 공정을 자동으로 제어하고, 공정중단 시점을 효율적으로 찾아내어 생산 효율을 높인다.

연마 로봇의 원격 관리를 위한 모니터링 시스템 개발 (Development of Monitoring System for Remote Management of Polishing Robot)

  • 고석조;이민철;홍창우
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 2002년도 춘계학술대회 논문집
    • /
    • pp.625-631
    • /
    • 2002
  • In the previous study, a polishing robot system was developed to automate the polishing process and to cope with the shortage of skilled workers. This polishing robot system has several advantages: reduced time for setting polishing work, decreased labor costs, effective operation, continuous polishing work without an operator, improved machine accuracy, and the ability to polish a free curved surface die. However, still the problem remains that a worker must stay to monitor the polishing process in the poor working conditions for a long time. Nowadays some advanced manufacturing companies need to find a way to check the performance of their production equipments and plants from remote sites. Thus, this study constructed the communication network and developed the monitoring programs (a servo program and a client program) to operate the polishing robot from remote sites. Using these programs, workers are able to monitor and control the polishing robot on the web page, in any place where internet service is possible. To guarantee a stable operation in spite of a variable computer operating environment, the monitoring system is implemented in Java. The experimental results showed that the developed monitoring programs provided a stable communication.

  • PDF

생산성 향상을 위한 연삭공정의 감시.제어시스템 개발 (Development of Monitoring/Control System for High Productive Grinding System)

  • 정병철;안중환;이상우
    • 한국정밀공학회:학술대회논문집
    • /
    • 한국정밀공학회 1994년도 춘계학술대회 논문집
    • /
    • pp.425-428
    • /
    • 1994
  • Non-uniform minute deformation of a cylinderical workpiece resulted from the heat treatment process prior to the grinding makes it diffeclt to control the approaching feedrate of a grinding wheelto a workpiece optimallywithout on-site detection of the grinding states in the plunge grinding. The 4-stage model of the plunge grinding process is proposed according to the state of contact between grinding wheel and workpiece ; precontact, partial contact, entire contact and spark-out. Despite of being scrious to the precision of workpiece finished, the duration of spark-out is determined empirically. The purpose of this research is to develop a monitoring/control system for saving non- production time and setting the optimal spark-out time based on sensor information in the plunge grinding using AE and ultra sonic sensor.

  • PDF