• Journal of Drive and Control
• /
• v.16 no.2
• /
• pp.72-79
• /
• 2019

Despite the development of electronic components and microprocessors, hydraulic actuators are still being applied in various applications. In some applications, there is a desire to apply a hydraulic actuator with a relatively small position error to the system. Various studies have been conducted to reduce the position error of hydraulic actuators. In this paper, the position error of the hydraulic actuator when the hydraulic oil pressure is supplied is defined as the offset generated by the servo valve, and the method for correcting the servo valve offset has been studied. A method for compensating the servo valve offset was proposed and it was verified through experiments that the position error of the hydraulic actuator was reduced. We also compared the servo valve offset correction method and controller using the PID control and disturbance observer used to reduce the position error of the hydraulic actuator. No-load test and load test were performed to confirm the performance of the servo valve offset correction method. The results of the study were compared with those obtained by using the disturbance observer and PID control.

• Journal of Drive and Control
• /
• v.15 no.4
• /
• pp.48-54
• /
• 2018

The hydraulic servo actuator has always operated very precisely with high frequency and small displacement, and is used continuously for a long time. The hydraulic servo actuator of the test equipment used in the accelerated life test in order to guarantee the service life of the automotive parts failed earlier than the products before finishing the test. This study performed an analysis on the cause of the failure of the hydraulic servo actuator used in the test equipment, changed the design of the actuator to solve the root cause of the main failure mode, and developed the improved servo actuator. Based on above process, this study established a better performances and longer lifetime of the servo actuator after testing.

• Journal of Drive and Control
• /
• v.18 no.1
• /
• pp.17-23
• /
• 2021

The flow signal or spool position signal is used to determine the dynamic characteristics of directional control valves. Alternatively, the signal of spool position or flow can be replaced with the velocity of a low friction, low inertia actuator. In this study, the frequency response of the servo valve equipped with a spool position transducer is measured with a metering cylinder. The input signal, spool displacement, load pressure, and velocity of the metering cylinder are measured, and the theoretical results from the transfer function analysis are verified. The superposition rule for magnitude ratio and phase angle was found to be always applicable among any signal type, and it was found that the load pressure signal is not appropriate for use as the signal for measuring the frequency response of a servo valve. It was confirmed that the frequency response of a servo valve using metering cylinder was similar to the results from a spool displacement signal. The metering cylinder used for measuring the frequency response of a servo valve should be designed to have sufficiently greater bandwidth frequency than the bandwidth frequency of the servo valve.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.11
• /
• pp.1176-1181
• /
• 2004

In high-capacity disk drives with ever-growing track density, the allowable level of position error signal(PES) is becoming smaller and smaller. In order to achieve the high TPI(track per inch) disk drive, it is necessary to improve the writing accuracy during the servo track writing(STW) Process through the reduction of track mis-registration sources. Among the main contributors of the non-repeatable runout(NRRO) PES, the disk vibration and the head-stack assembly vibration is considered to be one of the most significant factors. Also the most contributors of repeatable runout(RRO) come from the contributors of NRRO which is written-in at the time of STW process. In this paper, the effect of NRRO on servo written-in RRO is Investigated by experimentally, and the experimental result shows that the written-in RRO can be effectively reduced through a STW process under low dense medium condition such as semi-vacuum.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.46-51
• /
• 2001

To reach high areal density, less track pitch is expected and more servo bandwidth is required. One approach to overcoming the problem is by using dual stage servo system. In this system, a voice coil motor (VCM) is used as the primary stage while a milliactuator is used as the secondary stage. We have suggested new milliactuator based on the shear mode of piezoelectric elements to drive the head suspension assembly. In this paper, we introduce controller design method, PQ method. PQ method reduces the controller design problem for DISO(dual-input/single-output) systems to two standard controller design problems for SISO(single-input/single-output) problems. The first part of PQ method directly address the issue of actuator output contribution, and the second part allows the use of traditional loop shaping to achieve the overall system performance. This paper shows how to employ the PQ method to meet aggressive close-loop performance specifications for a disk drive system with a VCM and piezoelectric milliactuator.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.1
• /
• pp.99-107
• /
• 2005

According to recent trend, hard disk drive(HDD) has been smaller and less weight. Therefore, it needs new method of writing position information. In this thesis, a new controller that is suitable for SSW is proposed. The controller accepted SSW technology that is used to write position information in current HDD industry. The important condition to perform SSW is to reach constant velocity decided from the head velocity profile as fast as possible. The constant velocity decides the positional accuracy of spiral pattern and setup time decides the capacity of HDD. The head velocity profile as a reference signal must be designed not to cause resonance mode. The proposed controller was designed with consideration of these 3 elements, and it properly works for SSW. The velocity profile designed with SMART control not only minimizes the jerk, but also does not cause the resonance mode of a plant. After designing a conventional PID controller, it compared with electrical spring technique and ZPET technique.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.9
• /
• pp.122-132
• /
• 1993

In this paper, a self tuning control algorithm is proposed for the high performance drive of DC servo motor, which is adequate to the servo system having frequent load variation. In order to realization of the algorithm, the control system is developed using a fixed point high speed digital signal processor. TMS320C25. Control algorithm is composed of two parts. One is estimation law part using recursive least mean square method, the other is control law part using minimum variance control method. For the purpose of easiness of applying adaptive algorithm, developed control system is based o PC-DSP structure which can develop, debug programs and monitor the dynamic behaviors,etc. Through computer simulation and experimental results, it was verified that proposed control system could estimate system parameters and was robust to the variation of the load and as a result, was adequate to the servo motor drives.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.3
• /
• pp.553-558
• /
• 2012

An effort for motion control of multi-axis in robot have been continued recently. In this paper, we propose implementation method for AC servo driver that can be easily motion control of multi-axis in robot. This proposed method implement EtherCAT communication technologies of bi-directional optical communication based on single optical core method that applied WDM for communication between control stage which is upper and AC servo drive stage.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.2
• /
• pp.168-175
• /
• 2011

Contouring accuracy of CNC machine tools is very important for high-speed and high-precision machining. In particular, large contour error may occur during corner tracking. In order to reduce the corner contouring error, acceleration and deceleration control or tool-path planning methods have been suggested. However, they do not directly control the corner contouring error. In the meantime, network servo systems are widely used because of their easiness of building and cost effectiveness. Communication latency between the master controller and servo drives, however, may deteriorate contouring accuracy especially during corner tracking. This paper proposes a control strategy that can accurately calculate and directly control the corner contouring error. A prediction control is combined with the above control to cope with communication latency. The proposed control method is evaluated through computer simulation and experiments. The results show its validity and usefulness.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.9
• /
• pp.36-46
• /
• 1994

A analog disturbance observer, which is suitable for servo motor drive, was employed to suppressi control of the impact drop disturbance. The main advantage of the observer is that a fast response disturbance estimation is obtained using the detected motor cuttent and speed. And the new M/T method for motor speed detection is proposed. The method should be able to reduce the detection dead time compared with the Ohmae's M/T method. Also, the low speed control of a servo motor using instantaneous speed detection method is described. To estimate the instantaneous speed from the average speed, the speed estimator of the first order is proposed. Actually we confirmed that these methods improve the speed control performance of the servo system with experiments.