• 마이크로전자및패키징학회지
• /
• 제29권4호
• /
• pp.21-27
• /
• 2022

저렴한 전도성 흑연을 인쇄전자 공법으로 유연 압력 센서를 개발하였다. 유연 압력 센서는 의료, 게임, AI 등 미래 산업에 활용될 소재로 각광받고 있다. 유연 압력 센서용 인쇄전극을 다양한 전기-기계적 특성을 평가한 결과 최대인장률 20%, 30°의 인장/굽힘, 간이 맥박 시험에서 일정한 저항 변화율을 보였다. 이렇게 검증이 완료된 전극을 시뮬레이션하여 더 적합한 matrix 패턴을 설계하였다. Serpentine 패턴을 활용하여 matrix 패턴 제작과 인캡슐레이션을 동시에 진행할 수 있는 공정을 활용하였다. 인쇄된 흑연 전극의 한쪽 면에 접착력 증가를 위한 O₂ 플라즈마 표면처리하고, 90°회전시켜, 라미네이션 공정을 통해 2개의 전극을 하나로 제작하였다. 이렇게 제작된 matrix 패턴을 인체의 손목 맥박 위치에 부착하여 실측을 진행한 결과 남녀 상관없이 일정한 저항 변화율을 보였다.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제11권2호
• /
• pp.73-81
• /
• 2003

The performance of heat exchanger using oscillating heat pipe (OHP) for low temperature waste heat recovery was evaluated. OHP used in this study was made from low finned copper tubes connected by many turns to become the closed loop of serpentine structure. The OHP heat exchanger was formed into shell and tube type. R-22 and R-141b were used as the working fluids of OHP with a fill ratio of 40 vol.%. Water was used as the working fluid of shell side. As the experimental parameters, the inlet temperature difference between heating and cooling water and the mass velocity of water were changed. The mass velocity of water was changed from 30 kg/$m^2$s to 92 kg/$m^2$s. The experimental results showed that the heat recovery rate linearly increased as the mass velocity and the inlet temperature difference of water increased. Finally, the performance of OHP heat exchanger was evaluated by $\varepsilon$-NTU method. It was found that the effectiveness would be 80% if NTU were about 1.5.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1876-1878
• /
• 1999

Developed was a 5kW-class polymer electrolyte membrane fuel cell(PEMFC) system comprised of fuel cell stack, fuel processing, thermal and water management subsystems and ancillary equipments. Several large single cells have been fabricated with different gas flow field patterns and paths, and the gas flow field pattern for the stack has been determined based on the single cell performance of thin film membrane electrode assembly (MEA). The PEMFC stack was consisted of 100 cells with an electrode area of $300cm^2$, having serpentine flow pattern. Fuel processing was developed including an autothermal methanol reformer and two preferential CO oxidation reactors. The fuel processing was combined to PEMFC operation system consisted of air compressor and thermal and water management subsystems. The PEMFC stack showed performance of 5kW under the supply of $H_2$ and air, but its performance was lowered to 3.5kW under the supply of reformed gas.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3418-3422
• /
• 2007

The neutron imaging technique was used to investigate the water discharge characteristics at PEMFC. Prior to investigation of water discharge characteristics, the linear attenuation coefficient for water at Neutron Radiography Facility (NRF) was calibrated. The feasibility test apparatus was consisted of pressurized air and water in order to simulate the actual operating PEMFC. The feasibility tests have been performed at 1-parallel serpentine type with 100 $cm^2$ active area and different air flow rate (1, 2, and 4 lpm). The total water volume variations at each condition were calculated from the neutron images. The water at channel is well discharged as soon as supplying the pressurized air into the PEMFC. However, because the water at MEA isn't removed the total water volume is constant after 150. Therefore more effective method is needed in order to discharge water at MEA, and the neutron imaging technique is helpful for it.

• 한국환경생태학회지
• /
• 제14권2호
• /
• pp.119-126
• /
• 2000

충남 사문암 지역인 광천, 홍성, 백동, 대흥 및 유구지역의 토양, 식물체(참억새, 쑥, 리기다소나무) 및 지표수, 갱내수의 중금속 함량을 분석한 결과 사문암 토양의 Ni, Cr 및 Co 원소가 변성암 토양에 비하여 10~13배높았으며 이 원소들이 serpentine factor로 생각된다 사문암 지역간에는 이들원소의 차이가 뚜렷하지 않았다 변성암 토양식물에서보다 사문암 토양 식물에서 Ni, Cr, Co등이 높았다 리기다소나무의 원소 흡수량은 비교적 낮았고 3종 식물에서 대체로 뿌리의 원소 함량이 지상부 함량보다 높았으며 사문암 토양에서는 Ni, Cr, Co, Mo, Sc, As 및 Fe 원소들이 쑥보다 참억새에서 높았다 사문암 토양에서 생육하는 식물체 지상부의 생물학적 흡수계수는 Ni, Cr, Co, Zn, Sc, As 및 Fe 원소는 참억새에 높고Zn은 쑥에서 높았다,. 사문암 토양에서 뿌리로부터 지상부로의 원소 전이는 Ni, Cr, Co, Zn As 및 Fe 원소에 대해 쑥에서 높았고 Mo와 Sc 원소는 리기다소나무에서 높았다. 따라서 사문암 토양에서 참억새가 중금속의 흡수율은 높고 중금속에 대한 내성은 강할 것으로 사료된다 대흥지역에서 광산의 오염이 지표수 및 갱내수의 Ni. Cr, Co, Zn 및 Fe 등의 원소 농도를 높게 하였으며 비오염 계류는 오염계류의 원소 농도를 희석시켰다.

• Journal of Electrochemical Science and Technology
• /
• 제8권4호
• /
• pp.331-337
• /
• 2017

A simple strategy is proposed herein for attaining uniform current distribution in direct methanol fuel cells by varying the catalyst loading over the electrode. In order to use the same total catalyst amount for a serpentine flow field, three spatial variation types of catalyst loading were selected: enhancing the cathode catalyst loading (i) near the cathode outlet, (ii) near the cathode inlet, and (iii) near the lateral areas. These variations in catalyst loading are shown to improve the homogeneity of the current distribution, particularly at lower currents and lower air-flow rates. Among these three variations, increased loading near the lateral areas was shown to contribute most to achieving a homogenous current distribution. The mechanism underlying each catalyst loading variation method is different; very high catalyst-loading is shown to decrease the homogeneity of the distribution, which may be caused by water management in the thick catalyst layer thereof.

• 대한기계학회논문집B
• /
• 제24권9호
• /
• pp.1239-1246
• /
• 2000

The objective of this work is to measure space and time resolved wall heat fluxes during nucleate pool boiling of R113/R11 mixtures using a microscale heater array in conjunction with a high speed CCD. The microscale heater array is constructed using VLSI techniques, and consists of 96 serpentine platinum resistance heaters on a transparent quartz substrate. Electronic feedback circuits are used to keep the temperature of each heater at a specified temperature and the variation in heating power required to keep the temperature constant is measured. Heat flux data around an isolated bubble are obtained with triggered CCD images. CCD images are obtained at a rate of 1000frames/second. The heat transfer variation vs. time on the heaters directly around the nucleation site is plotted and correlated with images of the bubble obtainedby using the high speed CCD. For both of the mixture(R11/R113) and pure system(pure R11, pure R113), the wall heat fluxes are presented and compared to find out the qualitative difference between pure and binary mixture nucleate boiling.

• 한국전산유체공학회지
• /
• 제8권2호
• /
• pp.16-23
• /
• 2003

A numerical study of the mixing of two fluids(pure water and a solution of glycerol in water) in a microchannel was carried out. By varying the glycerol content of the glycerol/water solution, the variation in mixing behavior with changes in the difference of the properties of the two fluids(e.g., viscosity, density, diffusivity) was investigated. The mixing phenomena were tested for three micromixers: a square mixer, a three-dimensional serpentine mixer, and a staggered herringbone mixer. The governing equations of continuity, momentum and solute mass fraction were solved numerically. To evaluate mixing performance, a criterion index of mixing of mixing uniformity was proposed. In the systems considered, the Reynolds numbers based on averaged properties were 1 and 10. For low Reynolds number (Re = 1), the mixing performance varied inversely with mass fraction of glycerol due to the dominance of molecular diffusion. The mixing performance by diffusion deteriorated due to a significant reduction in the residence time of the fluid inside the mixers.

• 한국주조공학회지
• /
• 제31권2호
• /
• pp.71-78
• /
• 2011

This study aims to investigate the formability of bipolar plates for fuel cell fabricated by vacuum die casting of ALDC 6. Cavity shape of mold is thin walled plate (size: $200mm{\times}200mm{\times}0.8mm$) with a serpentine channel (active area: $50mm{\times}50mm$). Before bipolar plate was made by HPDC, computational filling behavior and solidification was performed by MAGMA soft. The final mold design for location and direction of channel was determined by computational simulation. Also, according to injection speed conditions, simulation result was compared to actual die casting experimental result. When vacuum pressure, injection speed of low and high region is 350 mbar, 0.3 m/s and 2.5 m/s respectively, products had few casting defects. On the other hand, at the same as injection speed, without vacuum pressure, products had many casting defects between end of the channel and overflow.

• 한국실내디자인학회논문집
• /
• 제24권6호
• /
• pp.119-127
• /
• 2015

Sou Fujimoto is well known as the 3rd Japanese architect to participate in the Serpentine Pavilion project, especially youngest of all architects. His projects seem very experimental yet inviting, modern yet comforting and these feeling may be resulted in his metaphor of 'Forest' that is very often mentioned in his writings which originally comes from his personal experience of the city and nature. The purpose of this paper is to understand the Fujimoto's metaphor of 'Forest' and design language he uses to express this very idea. The researchers have analyzed Fujimoto's writings and interviews in order to understand his general design ideas and process, then extracted wordings describing 'Forest' in his works. Four main concepts were found and categorized as follows: blurring territorial boundaries, proliferation of parts, manipulating spatial relationships, and ambiguity in function. Then two or three projects were selected and analyzed in each category to understand design methods used. The results show that Fujimoto enjoys using gradation of density to blur territorial boundaries in order to express ambiguous outline of forest, and fractal reproductions in proliferation of parts to uses express wavering whole and modifying angles in manipulating spatial relationships to show hidden order.