• 한국농공학회지
• /
• 제17권1호
• /
• pp.3655-3665
• /
• 1975

This study was intended to develop a method for measuring the grain separating performance of threshers. The grain separating apparatus used for the experiment was designed and constructed, the function of which was to separate pneumatically mature and immature grain, chaff, straw, dust, and other impurities from the products of threshing. The apparatus has five material outlets where grains and impurities are fallen down by separation depending upon the specific gravity of the material white it moves above the outlets. The principle of design was to separate the mixture of mature grain, immature grain and chaff as distinct as possible, and to induce the mature grains onto the first outlet, the immature grains onto the second and the third, and the straw wastes onto the forth and the fifth outlets. The developed apparatus was tested to evaluate its separating performance with two rice varieties (Tongil and Mine-hikari) at different moisture levels and air velocities. The optimum conditions for operating the apparatus were found from experiment. The results are summarized as follows; 1. The degrees of separation, especially the amount of immature grain contained in the mature paddy, were dependent upon air speed delivered. The optimum air velocities for this apparatus for each levels of grain moisture contents were found from a series of experiments as follows; 14.7-15.3m/sec. for grain of 16 percent moisture content in wet basis, 15.3-16.0m/sec. for 20 percent, and 16.0-16.4m/sec for 24 percent. 2. Composition ratios determined based on the brine separating method was fairly well acted upon the developed apparatus, indicating its recollecting rate of the mature grains as 97.6 to 99.9 percent. The developed separatus acted similarly upon the two rice varieties which had different composition of immature paddy grain. In other words, the separating performance by the apparatus had a good correlation with the one by the brine separating method. 3. As immature grains were separated out unsatisfactory in these experiments than the brine separating method, further investigation may be needed to improve a separating performance of these materials. But the results obtained suggested a possibility of using the tester to replace the current hand separating method, ther eby enabling more consistent test results and also eliminating nearly all costly hand seperating operations.

• 한국농촌건축학회논문집
• /
• 제21권3호
• /
• pp.17-24
• /
• 2019

This study aimed to develop a mobile separating and sorting device for discharge sites to separate and sort mixed construction waste generated in small and medium scale in small provincial cities into inorganic materials and combustible materials. The study results can be summarized as follows: 1) As a result of analyzing the existing domestic technology for the separating and sorting mixed construction waste, a device sorting the waste by fusing the vibration screen, disc screen, air blowing methods and the separating and sorting the combustible waste is applied in Korea. 2) In foreign countries, the air blowing, screen, gravity sorters are used for separating and sorting combustible waste in the same way as in Korea. Especially German T Company suggests a construction waste separating and sorting system using an optical sorter. 3) As for the test device for separating and sorting mixed construction waste to be buried in landfill, the processing capacity was set as 16 tons per day. 4) For separating and sorting inorganic materials by granularity, this study set a trommel with two types of diameter as a basic. To operate the mobile all-in-one system, the device is designed to locate a conveyor, a combustible waste conveying device, inside of the trommel. 5) The device is designed in a mobile mode under the concept of primary separating and sorting device, and it can be transported using a 2.5-ton truck minimum. The diameter and length of the trommel are designed to be within 1500mm and 3000mm, respectively. In a further study, an optimized separating and sorting technology is planned to be presented through an experimental study for processing efficiency analysis at the mixed construction waste site by manufacturing the pilot experiment facility reflecting the design elements in the result of this study.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.515-518
• /
• 1997

Resident time of the centrifugal extractor for organic phase extraction using a height controlled separator weir and a divert plate is the important factor that affects significantly the chemical material extraction and the productivity in the chemical and mechanical processes. In this paper, it describes the design of the device for extraction of an organic phase from radioactive wastes, and considers phase separating weir and divert disk, both being designed to be adjustable in their positions, for effectively separating an organic phase. A height-adjustable separating weir unit used for separating the organic phase from the aqueous phase using a phase separating weir and designed to control the height of the separating weir as desired so as to allow the weir to be positioned at a boundary layer between two separated phases. The centrifugal extractor controls satisfactorily the mixed reaction time of two phases within the separator regardless of the variations of the mixing ratio of the two phases and the rotating speed of the extractor, is designed to be adjustable in its position in the vertical direction, thus allowing the user to appropriately select the mixed reaction time of the two phases within the extractor as desired. From development of a centrifugal extractor, it can effectively recover such usable elements, and preferably reducing the output quantity of radioactive wastes.

• 대한기계학회논문집B
• /
• 제20권4호
• /
• pp.1510-1520
• /
• 1996

An experimental study on the flow over the axisymmetric backward-facing step was carried out. The purpose of the present study is to investigate the effect of the separating streamline curvature on the reattachment length and to understand the structure of recirculating flows. Local mean and fluctuating velocity components were measured in the separating and reattaching axisymmetric region of turbulent boundary layer on the wall of convex cylinder placed in a water tunnel by using 2-color 4-beam fiber optics laser Doppler velocimetry. The study demonstrates that the reattachment length increases with increasing separating streamline curvature. It is also observed that the reverse flow velocity and turbulent kinetic energy increase with an increase in the separating streamline curvature. In addition, the behavior of maximum turbulent stresses show that the effect of separating streamline curvature is larger in the region of recirculating zone(X/H<2) than in the region of reattachment point.

• 대한수학회보
• /
• 제44권4호
• /
• pp.753-761
• /
• 2007

In this note we extend the results of [3] concerning subadditive separating maps from A=C(X) to B=C(Y), for compact Hausdorff spaces X and Y, to the case where A and B are regular Banach function algebras(not necessarily unital) with A satisfying Ditkin#s condition. In particular we describe the general form of these maps and get a result on continuity of separating linear functionals.

• Journal of applied mathematics & informatics
• /
• 제18권1_2호
• /
• pp.351-360
• /
• 2005

Let T be a regular semigroup and let S be a regular subsemigroup of T. In this paper we study the relationship between the idempotent separating congruence on S and the idempotent separating congruence on T, when T and S are connected by a splitmap ${\theta} : T {\to} S$.

• 대한교통학회:학술대회논문집
• /
• 대한교통학회 1998년도 Proceedings The 4th International Transport Symposium
• /
• pp.36-42
• /
• 1998

This article analyzes Chinese railways transportation management system, uses the experiences of other countries' railway transportation management system for reference, as well as discusses the necessity of reform of railway transportation management system based on separating train operation with rail equipment management. Moreover, the article also puts forward an imagination on the reform scheme of railway transportation management system based on separating train operation with rail equipment management.

• 한국농공학회지
• /
• 제17권3호
• /
• pp.3878-3884
• /
• 1975

This study was carried out to develop the throw-in type thresher with its size as small as possible. Developing the smallest possible size of the throw-in type thresher has been very important to increase mobility and to reduce the machine price. The thresher that developed for this purpose was tested as to threshing and separation performance for the samples collected in eight catch boxes under the concave while threshing. The amount of grain collected in each compartments was measured and the threshing and separating pattern along the total span of the threshing drum was determined. The performance of separating and threshing units of the test thresher and threshing loss was evaluated by use of the developed grain separating apparatus and the method for measuring the grain separating performance of threshers. The results are summarized as follows; 1. The unthreshed grain (drum losses) and semi-threshed grain did not appeared at all throughout the treatments. 2. When threshed by making use of the developed throw-in type thresher, the threshing grain loss at about 25 per cent grain moisture was about one-half when threshed at about 18 per cent grain moisture. 3. And its grain separating loss in higher feed rate was decreased in comparison with that of lower feed rate. These results suggests that the throw-in type thresher may be suitable for wet threshing and for higher feed rate of threshing. 4. Above 60 per cent of total grain passing through concave fell through the screen within a scant 30 cm from the feeding inlet. This threshing pattern may suggest that major threshing action may be finished before about one third of cylinder length. The required separating load extended over the whole drum span is so defferent that separating elements should be redesigned so as to accomodate this variable pattern of separation load. 5. It was apparent from the experiment that the length of the threshing drum of the throw-in type thresher could be reduced from 1285mm to about 1050mm without increasing grain separation loss greatly.

• 대한수학회보
• /
• 제53권1호
• /
• pp.263-272
• /
• 2016

By using the finite projective geometry method, the separating properties of linear constant-weight codes are presented. An algorithm is given for computing the cardinality of separating coordinate positions of certain disjoint codeword sets of linear constant-weight codes.

• 수산해양기술연구
• /
• 제34권2호
• /
• pp.139-143
• /
• 1998

In the fishing process on the sea eel pots, the most dangerous and difficult labor is manually separating process of several thousand pots from main line with high speed hauling operation. In this study, the automatic separating system of the pot from main line is developed. This system is composed with the clip connected to the pot by branch line, the keeper attached to the main line by pressing and the separator separating the clip and the keeper. In the experiment, static and dynamic characteristics of the system are investigated. From the considerations on the experimental results, it is ascertained that the automatic separating system of the pot from main line proposed in this study has good operating performance.