• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.9
• /
• pp.911-916
• /
• 2005

In this study, variations of water quality, sediment size and contaminant substances are analyzed at upstream and downstream in sewer systems in order to evaluate the characteristics of wastewater transformation by physico-chemical and biological reactions. The differences of DOC concentration between up and down stream showed the range of $-5.8{\sim}18.6$ from the result of continuous measurement at up and down stream. About 8.4% of DOC concentration was reduced and reduction rate was 2.3 mg/L/km. SS reduction rate was measured by 5.5 mg/L/km, 0.22 mg/L/min from upstream to downstream, which was twice than DOC reduction rate. When pollution load reduction was evaluated considering infiltration/inflow effect, DOC load was eliminated from 1,230 ka/d to 1,167 kg/d by physi-chemical and biological reaction in a sewer and 7.8% of the SS in upstream station was reduced under dry weather condition. The results showed that the characteristics of transformation process of wastewater in sewer should be considered for design and operation of wastewater treatment plant.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.481-486
• /
• 2020

To evaluate geochemical characteristics of surface sediments in Samcheok Port, the distribution characteristics of particle sizes, organic matters and heavy metals were investigated. The sediments showed a mixed property of sand, silt, and clay, however fine-grains dominated at the inner port and coarse-grains dominated at the outer port. The organic (COD, TOC, and IL) contamination of the sediment at the inner port were higher than that of the outer port, and the concentrations of total nitrogen and total phosphorus at the inner port was higher than those of the outer port. Also, heavy metals contamination of surface sediments at the inner port was higher than those of the outer port (except for As). From the results of high organic matter concentrations and C/N ratio at the inner port, it is considered that the contamination of organic matters was mainly derived from the land. The correlation analysis among the particle size, chemical composition, and heavy metals resulted in high correlation between silt-clay and heavy metals, and between organic matters and heavy metals. The sequential extraction results of heavy metals showed the sum of exchangeable, carbonate, and oxide fractions of Ni, Zn, Cu, Pb, Cd, and As were 14.8, 49.8, 39.1, 32.2, 51.8 and 26.6%, respectively.

• Ecology and Resilient Infrastructure
• /
• v.1 no.2
• /
• pp.68-81
• /
• 2014

In this study, the numerical simulation regarding the process and characteristics of topography change due to the vegetation recruitment and growth was carried out by adding the vegetation growth model to two-dimensional flow and sediment transport models. The vegetation introduction and recruitment on the condition for developing an alternate bar reduced the bar migration. The vegetated area and channel width changes were more significantly influenced by changes in upstream discharge rather than the duration of low flow. When the upstream discharge decreased, the vegetation area increased and the channel width decreased. The vegetation introduction and recruitment on the condition for developing a braided channel significantly influenced the characteristics of topography changes. In the braided channel, vegetation reduced the braided index, and when the upstream discharge decreased significantly, the channel topography was changed from the braided channel to the single channel. The vegetation area decreased as the upstream discharge increased. The channel width decreased significantly after the vegetation was introduced and it also decreased as the upstream discharge decreased. It was confirmed through the numerical simulation that a decrease in flood discharge accelerated the vegetation introduction and recruitment in the channel and this allowed to confirm its influence on the characteristics of topography changes qualitatively.

• Korean Journal of Remote Sensing
• /
• v.25 no.5
• /
• pp.445-454
• /
• 2009

Localized unprecedented torrential rain and heavy rainfall cause repeated damages and make it difficult to detect and predict the landslide caused by heavy rainfall. To analyze the landslide characteristics of Inje area this study used satellite images photographed after the occurrence of landslide caused by the typhoon Ewiniar occurred in July, 2006, and for GIS analysis purpose, interpreted the satellite images (SPOT5) visually to digitize into developing parts, water traveling parts and sediment parts. For analysis of spatial characteristics, landslide areas obtained from visual interpretation of digital map, 3rd & 4th forest vegetation maps and detailed soil map and grids were overlaid and analyzed. As a result, in regard to topographic features, landslide occurred at places, of which average slope is $26.34^{\circ}$, had south, south-east, south-west aspects and average altitude of 627m. From hydrological analysis, it was found out that water traveling area rapidly spread approaching water traveling area and sediment area. From forest type analysis, it was found out that landslide occurrence was high in pine woods, and in terms of girth class attribute, landslide occurred in small-sized woods, in which the crown occupancy of trees that have the diameter at breast height, 6~16cm, was greater than 50%. From the analysis of soil series, landslide areas constitute 37.85% of OdF and 37.35% of SmF, which had sandy loam soil and excellent drainage capacity. Through this study, landslides in Inje area were characterized and SPOT5 images of 2.5m resolution could be used. But there was a difficulty in determining water traveling parts adjacent to urban area.

• Journal of The Geomorphological Association of Korea
• /
• v.28 no.3
• /
• pp.13-26
• /
• 2021

In mountain gully, channelized debris flow is an important phenomenon in the process of topographical change. Social infrastructure as roads may be damaged by channelized debris flows, but there has been little information about their occurrence and movement to prepare for the risk of the debris flow. Most of the channelized debris flows occur during heavy rains in mountainous valleys that are difficult to access, so there are not many field data. In this study, the topographical characteristics of the catchment, the rainfall and runoff related to the debris flow, the sedimentary pattern and the cross-sectional change of the channel bed, and the underflow velocity of the gravel bed have been investigated and analyzed in the Singi gully where the channelized debris flows occurred. In the catchment, there was almost no sediment runoff because the vegetation combine with the debris landforms and covered the surface. Therefore, the obvious cause of the channelized debris flows is the collapse of the slope and bed of the gully. Even if the gravel, cobbles, and boulders of the channel bed were lost by debris flow, the thalweg change due to debris flow may not be significant because they are supplied from the gully side slope normally. After the gabion structures were installed, the debris flow increased the thalweg change, bed erosion and side slope of the gully. Various sedimentary structures in the gully were classified according to the factors supporting the sedimentation. The hypsometric curve of the gully reflects the debris landforms and vegetation characteristics of the watershed and the sediment runoff due to debris flow, etc. The relationship between the flow velocity and the hydraulic gradient was non-linear under the condition that the porous medium with gully bed gravels is saturated with water. These results may be used as basic data for channelized debris flow research.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.4
• /
• pp.347-360
• /
• 2015

Trace metals(As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Pb and Zn) concentrations in surface sediments of Jinhae bay in August of 2013 were measured to investigate the characteristics of trace metals distribution and to evaluate the metal pollution. Assessment for metal pollution was carried out using the sediment quality guidelines(SQGs) such as threshold effects level(TEL) and probable effects level(PEL) proposed by the ministry of onceans and fisheries(MOF) in Korea and geochemical assessment techniques(enrichment factor(EF) and geoaccumulation index ($I_{geo}$)). The mean concentration of trace metals in the sediments are as follows: 11.1 mg/kg for As, 0.52 mg/kg for Cd, 14.1 mg/kg for Co, 69.8 mg/kg for Cr, 57.2 mg/kg for Cu, 3.7 % for Fe, 0.064 mg/kg for Hg, 600 mg/kg for Mn, 40.1 mg/kg for Pb, 167.2 mg/kg for Zn. The spatial distributions of As, Co, Cr and Fe were not distinguished clearly in whole area. However, Cd, Hg, Pb and Zn were high in northern area of bay, and Cu and Mn were high in southeastern and eastern area of bay, respectively. The distribution pattern of trace metals, correlation matrix and R-mode factor analyses results revealed that the distribution of trace metals were mainly effected by the sediment grain size(Co, Cr and Fe), redox condition of sediments(Mn) and anthropogenic factors(As, Cd, Cu, Hg, Pb and Zn). Comparing the concentrations of several trace metals(As, Cd, Cr, Hg and Pb) with SQGs from Korea(TEL and PEL), the concentrations of Hg, Cd and Pb in sediment of northern area of bay were higher than TEL. EF and $I_{geo}$ values of As, Cd, Cu, Hg, Mn, Pb and Zn showed that these metals in sediments are enriched by anthropogenic activities in some areas, and pollution status for Cd, Hg and Pb in northern area and Cu in southeastern area of bay were concerned about current level, although those for As, Mn and Zn were not.

• Journal of the Korean Geophysical Society
• /
• v.7 no.3
• /
• pp.193-206
• /
• 2004

Geophysical data including chirp (3 7 kHz) subbottom profile and detailed bathymetry were obtained over three seamounts in the Ogasawara Fracture Zone (OFZ) of the western Pacific, as a part of manganese crust survey onboard R/V Onnuri in 2003. The OFZ is a 150-km-wide, 600-km-long rift zone, which separates the East Mariana and Pigafetta Basin. The OFZ is unique in that it includes many seamounts (e.g., Magellan Seamounts andseamounts on the Dutton Ridge). The sub-seafloor acoustic echoes obtained near the OFZ were classified into following types on the basis of their characteristics: types I-1(pelagic sediment with parallel or subparallel reflectors), I-2 (pelagic sediment with no internal reflectors), and III-1 (reef build-up complex) on summit; types II-1 and III-2 (basement outcrop) on flank rift zone and upper slope, respectively; type III-3 (slump) on the lower slope and embayment between the flank rift zones; types II-2 (debrite) on the base of slope and basin floor; and types II-3 (turbidite or pelagic sediment) and II-4 (turbidite) on the basin floor. The mass-wasting that produced the complex of type II-2 debrite and III-3 slump on the lower slope and basin may have been caused by (1) strong tensional stress in the OFZ which may cause the numerous fissures or basement faults and (2) complex of the faults on the summit and steep upper slope. The variations in the echo type of pelagic sediment in the summit of seamounts may be related with the changes in the depositional and/or erosional environments. Type I-2 pelagic sediment, which is characterized by a thin and intermittent coverage, was probably deposited at a sheltered area when the current was strong, whereas type I-1 pelagic deposit occurred during a stage of progressive sedimentation.

• Geophysics and Geophysical Exploration
• /
• v.20 no.3
• /
• pp.146-162
• /
• 2017

Multibeam and seismic data in the northwestern part of the Ulleung Basin were analyzed to study stratigraphy and evolutionary history of submarine canyon. A detailed analysis reveals that the sedimentary sequences in this area consist of four stratigraphic units separated by erosional unconformities. On the continental slope, these units are dominated by well-stratified facies with some slope failures, whereas these units show well-stratified and chaotic facies toward the basin floor. Generally, the sediment thickness is relatively thin on the slope, whereas thick sediment accumulation occurs on the base of slope and basin floor. Based on seismic characteristics and distribution, the deposition of each units are well correlated with the evolutionary history of the submarine canyon. Unit 1 directly overlying the acoustic basement has thin sediment layer on the slope, whereas its thickness gradually increase toward the basin floor. Compared to other units, Unit 2 is relatively thick accumulations on the slope and contains some slope failures related to faults systems. The mass transport sediments due to slope failures, mainly deposited on the base of slope as a submarine fan. The width and depth of submarine canyon increase due to dominant of the erosional process rather than the sediment deposition. Unit 3 is thin accumulation on the slope around the submarine canyon. Toward the basin floor, its thickness gradually increases. Unit 4 is characterized by thin layers including slides and slumps on the slope, whereas it formed thick accumulations at the base of slope as a submarine fan. The increase in the width and depth of submarine canyon results from the dominant of the erosional process and slope failures around the submarine canyon. Consequently, the formation of sedimentary units combined with the development of submarine canyon in this area is largely controlled by the amounts of sediment supply originated from slope failures, regional tectonic effects and sea-level fluctuations.

• Journal of Korean Society of Forest Science
• /
• v.108 no.4
• /
• pp.469-483
• /
• 2019

North Korea has experienced floods and sediment-related disasters annually since the 1970s due to deforestation. It is of paramount importance that technologies and trends related to forest restoration and soil erosion control engineering be properly understood in a bid to reduce damage from sediment-related disasters in North Korea, and to effect national territorial management following unification. This paper presents a literature review and bibliometric analysis including 146 related articles published in North Korea. First, we analyzed the textual characteristics of the articles. We then employed the VOSviewer software package to classify the research topic and analyzed this topic based on the time change. The results showed that articles on the topic have consistently increased since the 1990s. In addition, research related to soil erosion control engineering has been classified into four subjects in North Korea: (i) assessment of hazard area on soil erosion and soil loss, sediment related-disasters; (ii) hydraulic and hydrologic understanding of forests; (iii) reasonable construction of soil erosion control structures; and (iv) effects and management plan of soil erosion control works. The proportion of research related to the (ii) hydraulic and hydrologic understanding of forests had been significant during the reign of Kim Ilsung. However, the proportion of research related to the (i) assessment of hazard area on soil erosion and soil loss, sediment-related disasters, increased during the reign of Kim Jongil and Kim Jongun. Using these results, our analysis indicated that an interest in and need for soil erosion control engineering in North Korea has continually increased. The results of this study are expected to serve as a basis for preparing forestry cooperation between North and South Korea, and to serve as essential data for better understanding soil erosion control engineering in North Korea.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.4
• /
• pp.358-371
• /
• 2014

For the systematic scientific management in Cheonsu Bay of Korea, this study was conducedt to survey the particle composition, organic matter(I.L.) and heavy metals in farming and non-farming areas. The sediment of study area showed feature mixed property by sand, silt and clay. The farming area showed superior by fine-grained sediment, non-farming area showed superior by coarse-grained sediment. The organic pollution of farming area were appeared to be heavily polluted more than non-farming area. The concentration of total nitorgen in sediment was higher farming area than non-farming area. Also, in the case of heavy metals pollution in sediments, farming area was higher than non-farming area. The correlation analysis among to heavy metals, organic matter and particle size was found to have a good interrelationship. For evaluation of heavy metals pollution of sediments, three criteria are applied, Enrichment Factor(EF), Geoaccumulation index(Igeo) and NOAA criteria for sediment. In the case of EF, Heavy metals pollution was appeared to artificial effect all heavy metals if except Cu. In the case of Geoaccumulation index, Cu, Al, Pb was shown zero grade, that is non polluted group, and Cd, Hg, Cr was shown to 0~1 grade, that is mid polluted group, As was shown to 2 grade, that is moderately polluted group. In the case of NOAA, pollution levels of heavy metals except Cd belonged to a group of ERL(Effect range low)~ERM(Effect range median).