• Journal of the Mineralogical Society of Korea
• /
• v.31 no.2
• /
• pp.113-121
• /
• 2018

Baekasan Acheon cave located in Hwasun-gun, Jeollanam-do is a natural limestone cave only found in this province. In this study, the mineralogical and geochemical characteristics of speleothems collected from Baekasan Acheon cave were identified and the capability of carbonate mineral formation by aerobic microorganisms enriched from the cave and the mineralogical and geochemical characteristics of carbonate minerals formed by the microorganisms were investigated. The samples of sediments (clay) and speleothems (shelfstone and cave coral) were collected at three sites in the cave. The samples of shelfstone and cave coral were identified mainly as carbonate mineral, Mg-rich calcite, and clay minerals were composed of quartz, muscovite, and vermiculite by X-ray diffraction (XRD) analysis. To cultivate the carbonate forming microorganisms, parts of the sediment and speleothems were placed in D-1 medium containing urea, respectively, and the growth of microorganisms was observed under the aerobic condition at room temperature. The capability of carbonate mineralization of the cultured Baekasan Acheon cave microorganisms was examined through adding 1% (v/v) of the cultured microorganisms and calcium sources, Ca-acetate or Ca-lactate, into the D-1 medium. XRD analysis showed that the microorganisms cultured in cave deposits formed calcium carbonate ($CaCO_3$) under all conditions, and these microbial carbonate minerals included calcite and vaterite. The morphological characteristics and chemical composition of biologically formed minerals were observed by SEM-EDS showed various crystal forms such as rhomboid, spherical, perforated surface with Ca, C, and O of major chemical components. The existence of such microorganisms in the cave can contribute the formation of carbonate minerals, and it is likely to affect the geochemical cycles of carbon and calcium in the cave.

• Korean Journal of Veterinary Research
• /
• v.36 no.3
• /
• pp.681-692
• /
• 1996

The present study was conducted to isolate Babesia gibsoni by culture method of the microaerophilous stationary phase(MASP) and analyse the antigenic properties of the parasite by SDS-PAGE and immunoblot. The results obtained were summarized as follows. The protozoan parasite Babesia gibsoni multiplied in canine erythrocytes in RPMI 1640 medium(pH7.0) containing 20 40% normal canine serum under the MASP condition of 5% CO2 and 95% air at $37^{\circ}C$ incubator. The levels of parasitaemia in the erythrocytes were shown more higher by exchanging the medium at 24 hours interval. Under the above condition of MASP, the percentage of parasitized erythrocytes(PPE) after incubation for 8 days increased about 14 times more than that in the initiation of the 1% infected canine erythrocyte culture. The parasites were purely isolated from the MASP culture of red blood cells collected from dogs infected with Babesia gibsoni naturally or artificially. Among the total of 36 canine(Pit-bullterier) blood samples the parasites were isolated from 17 cases(47.2%) in the MASP culture while the parasites were detected from 20 cases(56%) and 12 cases(33.3%), respectively, by indirect fluorescent antibody(IFA) test and direct light microscopy(DLM). On the other hand, Babesia gibsoni was isolated by MASP culture from 15 cases(75%) and 11 cases(92%) of positive cases of IFA and DLM, respectively. In the analysis of the erythrocytic merozoite(AEOM) antigen derived from infected dog approximately 11 antigenic bands in molecular weight of 130, 120, 97.4, 92, 80, 52, 50, 42, 36, 30 and 29 KDa were observed on SDS-PAGE. Antigenic bands in the endoerythrocytic merozoite(CEOM) antigen derived from infected erythrocyte (sediment) in MASP culture were much similar to those of AEOM bands. In the exoerythrocytic merozoite(CEEM) antigen derived from supernatant of the infected erythrocyte culture approximately 20 antigenic bands were observed and the molecular weight of the major bands among these were 140, 120, 114, 105, 96, 93, 92, 80, 60, 52, 50, 38, 36, 30, 24, 18.5 and 16 KDa. In the protein patterns of AEOM and CEOM antigen by immunoblot 15 bands were observed and these patterns were much similar between each other. The molecular weight of the major bands in the both antigens were 130, 120, 80, 60, 52, 50, 42, 30, 29, 18.5 and 16 KDa. Approximately 21 bands were observed in CEEM antigen and the molecular weight of the major bands were 140, 120, 96, 92, 85, 80, 76, 60, 52, 50, 37, 30, 24, 16 and 15 KDa. The specific antigenic bands in the artificially infected dogs were firstly observed at 3 weeks afrer inoculation of infected blood and these antigenic bands were maintained up to 18 months after inoculation. In the immunoblot of the sera of the splenectomized dogs the specific antigenic bands with the molecular weight of 93 KDa and 52 KDa, respectively, were observed weakly comparing to those of non-splenectomized dog. In immunoblot of the sera collected from the naturally infected dogs the antigenic bands were observed as same as those of artificially infected dogs while antigenic band of 29 KDa in some individual dog showed strongly. In comparison of immunoblot of the sera collected from dogs non-treated and treated with diminazene aceturate(7mg/kg, IM) after artificial infection no differences of antigenic bands were observed. In analysis of antigenic bands by digoxigenin glycan/protein double labeling, antigenic bands in the molecular weight of 106, 60 58, 36, 30 and 29 KDa were determined as glycoproteins.

• 한국해양학회지
• /
• v.22 no.3
• /
• pp.130-142
• /
• 1987

Sedimentological characteristics of the surface sediments in the southern sea off Cheju Island are described from analyses of bottom sediments. The sediments are subdivided into seven textural classes, muddy sand, slightly gravelly muddy sand, sand, clayey sand, sandy clay, sandymud, silty sand. Sand-size sediments are distributed in the southeastern part and/or around the Island, whereas sandy and muddy sediments are mainly distributed in the central and southern parts of the study area. A small portion of mud patch is located in the southwestern part of the area. According to the textural parameters analysis, sediments in the study area are poorly sorted(av.2.52 ), positive skewed(av.1.61 ), leptokurtic(av.1.74 ), transported by saltation and/or suspension, and roundness of quartz is varied from angular to surrounded, which suggesting that the depositional environment is not simple. The calcium carbonate content is on the average 26.99%, and commonly abundant in sand-size sediments, whereas organic matter content in the bulk sediment is on the average 6.70% and usually dominant in fine-grained sediments.Light minerals consist of quartz(av56.01%),Na-Ca feldspar(av.6.15%),K-feldspar(av.9.22%) and rock fragments(av28.11%).The contect onquartz and K-feldspar increases continuously away from the Cheju Island. As a result of geochemical analysis,concentrations of the elements are as follow:Zn:19.42-43.52 ppm (av.30.67ppm),Mn:50-304 ppm(av139.39ppm),Cr:3.54-10.68ppm(av6.50ppm),Pb:5.52-41.68ppm(av.15.60ppm), Co:7.08-14.68ppm (av.10.78ppm),Ni:19.70-42.42ppm(av.29.57ppm),Cu:3.14-9.12ppm(av.5.14ppm),Fe:0.48-2.08% (av1.22%),Ca:0.32-13.16%(av6.60%),Al:0.06-0.08%(av.0.27%),Mg:0.12-0.76%(av.0.53%)na:0.11-0.51%(av.0.36%) Ag:0.48-4.08ppm(av.1.22ppm).Among these elements,the content of Zn,Cu,Cr,Mn,Fe,Al,Mg,Pb and Na increase toward the southwestern area,while the content of Ca and Ag SHOWS the reversed distribution trend.Such a distribution pattern seems to imply that spatial distrivution of heavy metals is closely related to the variation in grain size. X-ray diffractogram show that the minerals in clay from the southwestern mud patch are illite ,chlorite, kaolinte,feldspar and calcite.The bulk of illite in th mud zone is believed to be originated from Huanghe and Yangytze River.The mud patch in this region contains the diagnostic calcite peak,and the concentration of Ca,ni,Pb,Ag are similar to Huanghe type,which indicates that the greater part of these clay fractions may have been derived from the Huanghe River.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.13 no.2
• /
• pp.45-56
• /
• 1980

Farming density of oyster cultured in Hansan-Geoje Bay was studied to obtain the optimal farming density based on the biosedimentation analysis and the annual yield data from 1970 to 1979. Farming density of oyster extrapolated by means of pollution grade of sediment is significantly correlated to COD and phaeophytin content of the bottom mud of the bay. Pollution grade is linearly related to the number of oyster clusters suspended in the unit area. Optimal farming density was $0.12\;string/m^2$ in case of raft culture, and it was $0.12\;string/m^2$ in case of long-line culture. Farming density was well expressed by the number of strings per raft and the area covered by a raft. As strings per raft increased from 350 to 558, total yield from a raft increased and when occupied sea area per raft ranged from $1.000\;m^2\;to\;6,000\;m^2$, the yield per raft linearly increased as the area increased. This analysis suggests that the optimal density be 0.11 string per unit area $(m^2)$. As increasing the number of strings per $m^2$ the yield per string decreases, and this is well dipicted by a linear function. At this time the yield per unit area increases when the number of string increases up to the density of $0.13\;strings/m^2$. From the point of these three comprehensive analyses the optimal density was $0.11\~0.13\;string/m^2$ in case of raft culture and $0.25\;strings/m^2$ in case of long-line culture in Hansan-Geoje Bay. The maximum expected yield of oyster in Hansan-Geoje Bay is approximately 5,600 tons when maintained the string density at $0.11\~0.13\;string/m^2$.

• Geophysics and Geophysical Exploration
• /
• v.12 no.1
• /
• pp.132-142
• /
• 2009

The Tamar rift valley runs through the City of Launceston, Tasmania. Damage has occurred to city buildings due to earthquake activity in Bass Strait. The presence of the ancient valley, the Tamar valley, in-filled with soft sediments that vary rapidly in thickness from 0 to 250mover a few hundreds metres, is thought to induce a 2D resonance pattern, amplifying the surface motions over the valley and in Launceston. Spatially averaged coherency (SPAC), frequency-wavenumber (FK) and horizontal to vertical spectrum ratio (HVSR) microtremor survey methods are combined to identify and characterise site effects over the Tamar valley. Passive seismic array measurements acquired at seven selected sites were analysed with SPAC to estimate shear wave velocity (slowness) depth profiles. SPAC was then combined with HVSR to improve the resolution of these profiles in the sediments to an approximate depth of 125 m. Results show that sediments thicknesses vary significantly throughout Launceston. The top layer is composed of as much as 20m of very soft Quaternary alluvial sediments with a velocity from 50 m/s to 125 m/s. Shear-wave velocities in the deeper Tertiary sediment fill of the Tamar valley, with thicknesses from 0 to 250m vary from 400 m/s to 750 m/s. Results obtained using SPAC are presented at two selected sites (GUN and KPK) that agree well with dispersion curves interpreted with FK analysis. FK interpretation is, however, limited to a narrower range of frequencies than SPAC and seems to overestimate the shear wave velocity at lower frequencies. Observed HVSR are also compared with the results obtained by SPAC, assuming a layered earth model, and provide additional constraints on the shear wave slowness profiles at these sites. The combined SPAC and HVSR analysis confirms the hypothesis of a layered geology at the GUN site and indicates the presence of a 2D resonance pattern across the Tamar valley at the KPK site.

• Korean journal of applied entomology
• /
• v.44 no.2
• /
• pp.97-108
• /
• 2005

Samples of water, soil, and sediment were taken from 10 streams near Andong, Korea in May 2004. To assess the degree of environmental pollution of each stream, chemical pollutants such as total notrogen (T-N), total phosphorus (T-P), chemical oxygen demand (COD), heavy metals, organophosphorus pesticides, organochlorine pesticides, and dioxin-like PCB congeners were analyzed by standard process tests or U.S. EPA methods. In addition, biomarkers originated from insect immune systems of beet armyworm, Spodoptera exigua, were used to analysis of the environmental samples. Except Waya-chun stream showing T-N content of 9.12 mg/L, most streams were contaminated with relatively low levels of overall pollutants in terms of T-N, T-P, and COD, compared to their acceptable environmental levels designated by the Ministry of Environment. Contents of Pb and Cd in samples of each stream were much lower than environmentally permissible levels. However, several times higherconcentrations of Pb and Cd were found in locations at Mi-chun, Kilan-chun, and Hyunha-chun streams, in comparison with other streams. Diazinon, parathion, and phenthoate compounds among organophosphorus pesticides were detected as concentrations of 0.19, 0.40, and $1.13\;{\mu}g/g$, respectively, from soil sample collected in the vicinity of Mi-chun stream. On the other hand, 16 organochlorine pesticides and 12 dioxin-like PCB congeners, known as endocrine disrupting chemicals, selected in this study were not found above the limit of detection. Biomarker analyses using insect immune responses indicated that Waya-chun stream was suspected as exposure to environmental pollutants. Limitation and compensation of both environmental analysis techniques are discussed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.36 no.1
• /
• pp.55-61
• /
• 2003

This study was conducted to evaluate distribution and behavior characteristics of heavy metals for tidal flat sediments in the Saemankeum area. The value of heavy metal contents in the tidal flat sediments were higher than that surveyed in 1994, but showing that it's lower when compared with the value of Shiwha lake. Enrichment factors in the tidal flat sediments showed below 1 except for Pb and Zn. Metal excesses was appeared that Cu, Cr, Fe, Mn lacked and Pb, Zn were high. The correlation analysis between heavy metals and organic matters was found high positive relationship (r=0.424$\~$0.839), especially correlation coefficient between ignition loss and oxide Al, Fe, Mn showed high positive relationship above 0.7. The correlation analysis between Brain size and hear metals was found that as grain size was small, heavy metals contents were increased. Correlation coefficient between silt and heavy metals except for Cu, Pb showed high positive relationship as 0.552$\~$0.732.

• Journal of Wetlands Research
• /
• v.15 no.1
• /
• pp.149-157
• /
• 2013

The weirs built so far are mainly overflow type weirs overflowing to the upstream. Main advantages of overflow type weirs are, effective water resources management and easy design, construction and maintenance due to many accumulated studies. However, due to the special feature of the overflow type weir where water overflows through the upstream of the weir, the silt coming from the upstream is not discharged to the downstream of the weir. This increases the river bed and reduces the reservoir capacity, and as a result, the weir loses its function. A underflow type weir with a water gate has been implemented in order to solve such sediment deposit and weir maintenance problems. However due to the design problem of recently constructed underflow type weirs, the river bed of the downstream of a weir has been scoured. And this leds to a structural problem. In this study, the flow characteristics of overflow type weirs and underflow type weir, hydraulic jump length analysis depending on change of water depth and the amount of specific energy loss generated per unit length depending on a weir type have been compared and analyzed, for the effective design and management of the weirs. The experiment results show that, when identical upstream conditions of underflow type weir and an overflow type weir were maintained, the hydraulic jump length was up to twice longer with Fr(Froude number) 3.5 of the hydraulic jump length at the underflow type weir, and the hydraulic jump length gradually decreased as the downstream water depth increased. The comparative analysis result of the amount of specific energy loss generated per unit length showed that the amount of energy loss per unit length was twice higher for an overlfow type weir than a underflow type weir. Therefore, in case of a underflow type facility, an additional energy reduction facility is determined to be necessary for safety of water construction structures.

• The Korean Journal of Petroleum Geology
• /
• v.3 no.1 s.4
• /
• pp.1-15
• /
• 1995

Seismic reflection profiles and exploratory drilling well samples from the southern marginal-continental shelf basin of Korea delineate that the Tertiary sedimentary sequences can be grouped into five sequences (Sequence A, Sequence B, Sequence C, Sequence D and Sequence E, in descending order). Paleontologic data, K-Ar age datings, correlation with tuff layers and sequence stratigraphic analysis reveal that the sequences A, B, C, D and E can be considered as the deposits of Holocene $\~$ Pleistocene, Pliocene, Late Miocene, Early $\~$ Middle Miocene and Oligocene, respectively. The sequence stratigraphic and structural analyses suggest that the southern part of the Cheju Basin had experienced severe folding and faulting. NE-SW trending strike-slip movement is responsible for the deformation. The sinistral movement of strike-slip fault ceased before the deposition of Sequence B. Age dating and rare-earth elements analysis of volvanic rocks reveal+ that the Sequence D was deposited during the Early $\~$ Middle Miocene and the Sequence I was deposited earlier than the deposition of the Green Tuff Formation. Sedimentary petrological studies indicate that sediments of the Sequence I came from the continental block provenance. After the deposition of the Sequence E, uplift of the source area resulted in increase of sediment supply, subsidence and volcanic activities. The Sequence D show these factors and the sediments of the Sequence D are considered to be transported from the recycled orogenic belt.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.4
• /
• pp.383-397
• /
• 1999

For sites to be investigated, the results of such an investigation can be used in determining foals for cleanup, quantifying risks, determining acceptable and unacceptable risk, and developing cleanup plans t hat do not cause unnecessary delays in the redevelopment and reuse of the property. To do this, it is essential that an appropriately detailed study of the site be performed to identify the cause, nature, and extent of contamination and the possible threats to the environment or to any people living or working nearby through the analysis of samples of soil and soil gas, groundwater, surface water, and sediment. The migration pathways of contaminants also are examined during this phase. Key aspects of cost-effective site assessment to help standardize and accelerate the evaluation of contaminated soils at sites are to provide a simple step-by-step methodology for environmental science/engineering professionals to calculate risk-based, site-specific soil levels for contaminants in soil. Its use may significantly reduce the time it takes to complete soil investigations and cleanup actions at some sites, as well as improve the consistency of these actions across the nation. To achieve the effective site assessment, it requires the criteria for choosing the type of standard and setting the magnitude of the standard come from different sources, depending on many factors including the nature of the contamination. A general scheme for site-specific assessment consists of sequential Phase I, II, and III, which is defined by workplan and soil screening levels. Phase I are conducted to identify and confirm a site's recognized environmental conditions resulting from past actions. If a Phase 1 identifies potential hazardous substances, a Phase II is usually conducted to confirm the absence, or presence and extent, of contamination. Phase II involve the collection and analysis of samples. And Phase III is to remediate the contaminated soils determined by Phase I and Phase II. However, important factors in determining whether a assessment standard is site-specific and suitable are (1) the spatial extent of the sampling and the size of the sample area; (2) the number of samples taken: (3) the strategy of taking samples: and (4) the way the data are analyzed. Although selected methods are recommended, application of quantitative methods is directed by users having prior training or experience for the dynamic site investigation process.