• Transactions on Electrical and Electronic Materials
• /
• 제12권6호
• /
• pp.271-274
• /
• 2011

Screen-printed source and drain electrodes were used for a spin-coated and inkjet-processed zinc-tin oxide (ZTO) TFTs for the first time. Source and drain were silver nanoparticles. Channel length was patterned using screen printing technology. Different silver nanoinks and process parameters were tested to find optimal source and drain contacts Relatively good electrical properties of a screen-printed inkjet-processed oxide TFT were obtained as follows; a mobility of 1.20 $cm^2$/Vs, an on-off current ratio of $10^6$, a Vth of 5.4 V and a subthreshold swing of 1.5 V/dec.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.293-298
• /
• 2011

The most widely used method to form an electrode in industrial solar cells are screen printing. Screen printing is characterized by a relatively simple and well-known production sequence with high throughput rates. However the method is difficult to implement a fine line width of high-efficiency solar cells can not be made. The open circuit voltage(Voc) and the short circuit current density(Jsc) and fill factor(FF) need to be further improved to increase the efficiency of silicon solar cells. In this study, gravure offset printing method using the multicrystalline-silicon solar cells were fabricated. Gravure off-set printing method which can print the fine line width of finger electrode can have the ability reduce the shaded area and increase the Jsc. Moreover it can make a high aspect ratio thereby series resistance is reduced and FF is increased. Approximately $50{\mu}m$ line width with $35{\mu}m$ height was achieved. The efficiency of gravure off set was 0.7% higher compare to that of scree printing method.

• Transactions on Electrical and Electronic Materials
• /
• 제8권6호
• /
• pp.241-245
• /
• 2007

[ $(Ba_{0.9-x}Sr_xCa_{0.10})TiO_3$ ] (x=0.33, 0.36) powders were prepared by sol-gel method. $(Ba,Sr,Ca)TiO_3$(BSCT) thick films, undoped and doped with $MnCO_3$ and $Yb_2O_3(0.1{\sim}0.7mol%)$, were fabricated by the screen printing method on the alumina substrate. The coating and drying procedure was repeated 6-times. The Pt bottom electrode was screen printing method on the alumina substrate. These BSCT thick films were annealed at $1420^{\circ}C$ for 2 hr in atmosphere. The upper electrodes were fabricated by screen printing the Ag paste and then firing at $590^{\circ}C$ for 10 min. And then the structured and dielectric properties as a function of the doping amount of $Yb_2O_3$ were studied. As a result of the TG-DTA, exothermic peak was observed at around $670^{\circ}C$ due to the formation of the polycrystalline perovskite phase. All BSCT thick films showed XRD patterns of typical cubic peroveskite structure. The average thickness of BSCT thick films was about $70^{\mu}m$. The curie temperature and the dielectric constant decreased with increasing $Yb_2O_3$ doped content and the relative dielectric constant of the specimen, doped with 0.5 mol% $Yb_2O_3$ at BSCT(54/36/10), showed a best value of 5018 at curie temperature.

• 한국인쇄학회지
• /
• 제30권1호
• /
• pp.47-58
• /
• 2012

The inorganic powder EL lamp was made by screen printing technique with a phosphor ink and a dielectric ink. Value of color coordinates X and Y increased under the condition of supplying driving power to the inorganic powder EL lamp and changing voltage with constant frequency. When frequency was changed under the constant voltage, value of color coordinates X and Y were decreased with increasing frequency. However, level of change of color coordinates X was different from color coordinates Y. When voltage was increased under constant frequency, changing degree of color coordinates X and Y shows similarity. But under the constant voltage with changing frequency, color coordinates X and Y were differently changed that degree of change of color coordinates Y showed five times more than that of color coordinates X. As increasing thickness of phosphor ink and dielectric ink, level of voltage and frequency, color coordinates X and Y were slightly changed. According to the thickness of phosphor ink and dielectric ink, and level of voltage and frequency, color coordinate of color light was changed. Frequency was most important element influencing on the change of color coordinate.

• 한국염색가공학회지
• /
• 제23권3호
• /
• pp.169-178
• /
• 2011

The purpose of this study is to develop eco-printing method using natural dyes combined with chitosan treatment to impart various pattern effect on cotton fabric. It was examined whether tone-on-tone pattern effects could be produced by screen printing with chitosan paste and subsequently dip-dyed in natural dye bath. For polychromic colorants, fabrics were pre-mordanted and then screen printed with chitosan, while only chitosan printing treatment was applied for monochromic colorants. Color, dye uptake, washing, light and rubbing fastnesses of printed fabrics were measured in relation to the presence of chitosan printing. Pre-mordanting and chitosan printing treatment were applied to such polychromic colorants as madder, sappanwood, onion and cochineal. Also, printing pattern formation on fabrics was evaluated by differences in dye uptake and color. The results suggested that madder, onion and cochineal were effective on pattern formation. Regarding sappanwood, since dye uptake was increased only by pre-mordanting without chitosan printing treatment, there was little color difference and thus patterns were not clearly distinguished. Chitosan printing treatment tended to increase washing, light and rubbing fastnesses of dyed fabrics with polychromic colorants. Chitosan printing treatment was applied to monochromic colorants such as chlorophyll, gardenia and indigo and the effect of printing formation was examined according to the difference in dye uptake. Among monochromic dyes tried, chlorophyll was effective and chitosan printing improved washing and light fastnesses.

• 대한전자공학회논문지SD
• /
• 제45권4호
• /
• pp.72-77
• /
• 2008

본 논문에서는 Embedded resistor 적용을 위한 오개닉 기판 위에 캐버티(Cavity) 공정에 의해서 형성된 균일한 두께를 갖는 저항체의 제조 방법과 저항편차에 대해서 조사했다. 기존의 스크린 프린팅에 의해서 발생하는 PCB의 위치에 따른 저항값의 편차를 개선하기 위하여 캐버티 공정을 소개했다. 원하는 모양과 부피를 갖는 저항은 스크린 프린팅과 페이스트를 이용하여 cavity 공정에 의해 정확하게 형성되어 졌다. 이 방법은 PCB의 생산 공정시간을 줄일 수 있고, 스크린 프린팅의 정밀도에 의한 큰 영향 없이 빠르게 공정 조건을 배치할 수 있으므로써 생산량을 개선시킬 수 있다.

• 한국전기전자재료학회논문지
• /
• 제27권4호
• /
• pp.209-216
• /
• 2014

The screen printed technique is one of the electrode forming technologies for crystalline silicon solar cell. It has the advantage that can raise the production efficiency due to simple process. The electrode technology is the core process because the electrode feature is given a substantial factor (for solar cell efficiency). In this paper, we tried to change conditions such as squeegee angle $55{\sim}75^{\circ}$, snap off 0.5~1.75 mm, printing pressure 0.6~0.3 MPa and 1.6~2.0 mm finger spacing. As a result, the screen printing process showed an improved performance with an increased height higher finger height. Optimization of fabrication process has achieved 17.48% efficiency at screen mesh of 1.6 mm finger spacing.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.4.1-4.1
• /
• 2011

Recently, circuit printing technology has been considered as a promising alternative to conventional PCB fabrication, for it can greatly reduce the manufacturing costs. Even though printed circuit has many advantages over typical subtractive technology such as fewer processes, it has some disadvantages. The major problems are low adhesion and poor resolution. Efforts to overcome these problems have been mainly focused on ink developments with a limited success. And surface treatments showed some improvements. Therefore, various plasma treatments and primer coatings on plastic substrates have been tested. Plasma treatments using hydrocarbon gases including methane and propane improved the pattern quality of the inkjet printed circuit, which are further improved upon heating of substrate. On the other hand, there is little effect on the adhesion, which is improved only by a special primer coating. The adhesion of inkjet printed circuit has been increased more than 10 times upon treatment. As for the screen printed circuits, the overall effects are less significant since there is some organic binder in the ink. Nonetheless, the treatment has strong positive effects on pattern quality and adhesion. The adhesion of 1 kgf/cm2, which is comparable with those of the conventional PCB circuits, is possible through primer coating for both screen and inkjet printed circuits. The resulting circuit also showed good thermal, mechanical and electrical properties.

• 마이크로전자및패키징학회지
• /
• 제6권4호
• /
• pp.15-22
• /
• 1999

일반적으로 빌드업 다층 인쇄회로기판은 에칭, 도금등의 습식공정에 의해 제작이 이루어지므로 많은 장비와 많은 시간이 필요하게 된다. 이러한 습식공정은 양산에는 적합하지만 개발단계에서는 그리 적합하지 않은 방법이다. 본 연구에서는 스크린 인쇄기술을 도입하여 빌드업 다층 인쇄회로기판을 제작하여 보았다. 절연성 재료로는 광경화성수지 또는 열경화성수지를 사용하였으며 전도성 재료로는 전도성 페이스트를 사용하였다. 층간의 전기적 연결을 담당하는 비아와 회로를 형성하기 위해 스크린 인쇄공정을 통해 전도성 페이스트를 인쇄 하였다. 이러한 방법을 통해 제품의 개발 단계에서 기존의 빌드업 다층 인쇄회로기판 제작 공정과 비교하여 좀더 효율적인 방법을 제시하였다.

• 한국인쇄학회:학술대회논문집
• /
• 한국인쇄학회 2001년도 국제학술발표회
• /
• pp.120-126
• /
• 2001