• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.6
• /
• pp.368-378
• /
• 2019

Logic trees for probabilistic tsunami hazard assessment include numerous variables to take various uncertainty on earthquake generation into consideration. Results from the hazard assessment vary in different way as more variables are considered in the logic tree. This study is conducted to estimate the effects of various scaling laws and fault parameters on tsunami hazard at the nearshore of Busan. Active fault parameters, such as strike angle, dip angle and asperity, are adjusted in the modelling of tsunami propagation, and the numerical results are used in the sensitivity analysis. The influence of strike angle to tsunami hazard is not as much significant as it is expected, instead, dip angle and asperity show a considerable impact to tsunami hazard assessment. It is shown that the dip angle and the asperity which determine the initial wave form are more important than the strike angle for the assessment of tsunami hazard in the East Sea.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.6
• /
• pp.847-853
• /
• 2016

Applications of Si have been increasingly exploited and extended to More-Moore, More-than-Moore, and beyond-CMOS approaches. Ge is regarded as one of the supplements for Si owing to its higher carrier mobilities and peculiar band structure, facilitating both advanced and optical applications. As an emerging metal-oxide device, the junctionless field-effect transistor (JLFET) has drawn considerable attention because of its simple process, less performance fluctuation, and stronger immunity against short-channel effects due to the absence of anisotype junctions. In this study, we investigated lateral field scalability, which is equivalent to channel-length scaling, in Si and Ge JLFETs. Through this, we can determine the usability of Si CMOS and hypothesize its replacement by Ge. For simulations with high accuracy, we performed rigorous modeling for ${\mu}_n$ and ${\mu}_p$ of Ge, which has seldom been reported. Although Ge has much higher ${\mu}_n$ and ${\mu}_p$ than Si, its saturation velocity ($v_{sat}$) is a more determining factor for maximum $I_{on}$. Thus, there is still room for pushing More-Moore technology because Si and Ge have a slight difference in $v_{sat}$. We compared both p- and n-type JLFETs in terms of $I_{on}$, $I_{off}$, $I_{on}/I_{off}$, and swing with the same channel doping and channel length/thickness. $I_{on}/I_{off}$ is inherently low for Ge but is invariant with $V_{DS}$. It is estimated that More-Moore approach can be further driven if Si is mounted on a JLFET until Ge has a strong possibility to replace Si for both p- and n-type devices for ultra-low-power applications.

• Journal of Periodontal and Implant Science
• /
• v.27 no.2
• /
• pp.411-424
• /
• 1997

The purpose of this study was to evaluate in vitro the effects during subgingival calculus removal using Nd:YAG laser. The study group was consisted of 30 teeth with advanced periodontal disease extracted before the start of periodontal therapy. The specimens were divided into 8 different groups : 1) untreated control 2) scaling and root planing only 3) laser treated using 150mJ/pulse, 1sec, 5sec, contact mode 4) laser treated using 200mJ/pulse, 5sec, contact mode 5) laser treated using 150mJ/pulse, 1sec, non-contact mode 6) laser treated using 200mJ/pulse, 5sec, non-contact mode 7) laser treated using l5OmJ/pulse, 1sec, contact mode with water irrigation 8) laser treated using 200mJ/pulse, 5sec, contact mode with water irrigation. All specimens were prepared for evaluation by scanning electron microscopy(SEM). Specimens from Group 2 exhibited a smear layer of scale like texture with parallel instrument tracks resulting from curet use. Specimens treated by contact mode, Group 3 and 4 featured surface changes not observed· in controls such as charring, randomly distributed pitting and crater formation, and melting down of the tooth material and calculus. Specimens treated by noncontact mode, Group 5 and 6 featured similar surface changes observed in contact mode. However, the differences between contact and non-contact groups not significant. Specimens treated by contact mode with water irrigation, Group 7 and 8 featured slight surface change compared to other groups. The results suggested that Nd: YAG laser did not completely remove the subgingival calculus but was possible the application as adjunctive method.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.95-99
• /
• 2008

Cu has been used for metallic interconnects in ULSI applications because of its lower resistivity according to the scaling down of semiconductor devices. The resistivity of Cu lines will affect the RC delay and will limit signal propagation in integrated circuits. We investigated the electrolyte effects of the electroplating solution in the resistivity value of Cu films grown by electroplating deposition (EPD). The resistivity was measured with a four-point probe and the material properties were investigated with XRD (X-ray Diffraction), AFM (Atomic Force Microscope), FE-SEM (Field Emission Scanning Electron Microscope) and XPS (X-ray Photoelectron Spectroscopy). From these experimental results, we found that the electrolyte condition plays an Important role in formation of Cu film with lower resistivity by EPD.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.39 no.spc1
• /
• pp.132-141
• /
• 2006

Artificial structures have been designed as pilot structures to promote the creation and restoration of tidal flats. However, little information is available as to whether such artificial construction affects the macrobenthic community structure. We monitored the variation of the macrobenthic community structure and species composition near natural and artificial structures (seaweed and a timber fence) on the tidal flats near the Iwon Dike, Korea. In total, 137 macrobenthic species were recorded during this study, predominantly crustaceans (47%), polychaetes (18%), and molluscs (27%). Polychaetes comprised over 50% of the total density, followed by gastropods (38%) and crustaceans (11%). Macrobenthic species composition in the artificial and natural areas, was initially similar, but it differed after 7 months. The gastropod Umbonium thomasi, the most dominant species, was present at both sites in the first month after the start of the experiment, but disappeared at the artificial sites within 7 months, suggesting disturbance by the environmental factors. The number of species and diversity (H') varied significantly within sites at the beginning of the experiment, but no difference was observed after 7 months. Multivariate analysis (multidimensional scaling) revealed significant differences in community structure between the artificial and the natural areas from 7 months after the start of the experiment, except from 18 to 21 months. The community structures were mainly influenced by U. thomasi. Community structure at the artificial sites was affected by environmental variables, such as carbon, COD/IL sulfide, loss of ignition, kurtosis and silt, which changed over time. We observed no significant correlations between environmental variables and the dominant species, except in the case of Spio sp. and Macrophthalmus dilatatus, suggesting that the biological interactions and temporary disturbances such as typhoon, as well as the effects of artificial structures may also be important regulating factors in this system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.118-118
• /
• 2011

The Nano-Floating Gate Memory(NFGM) devices with ZnO:Cu thin film embedded in Al2O3 and AlOx-SAOL were fabricated and the electrical characteristics were evaluated. To further improve the scaling and to increase the program/erase speed, the high-k dielectric with a large barrier height such as Al2O3 can also act alternatively as a blocking layer for high-speed flash memory device application. The Al2O3 layer and AlOx-SAOL were deposited by MLD system and ZnO:Cu films were deposited by ALD system. The tunneling layer which is consisted of AlOx-SAOL were sequentially deposited at $100^{\circ}C$. The floating gate is consisted of ZnO films, which are doped with copper. The floating gate of ZnO:Cu films was used for charge trap. The same as tunneling layer, floating gate were sequentially deposited at $100^{\circ}C$. By using ALD process, we could control the proportion of Cu doping in charge trap layer and observe the memory characteristic of Cu doping ratio. Also, we could control and observe the memory property which is followed by tunneling layer thickness. The thickness of ZnO:Cu films was measured by Transmission Electron Microscopy. XPS analysis was performed to determine the composition of the ZnO:Cu film deposited by ALD process. A significant threshold voltage shift of fabricated floating gate memory devices was obtained due to the charging effects of ZnO:Cu films and the memory windows was about 13V. The feasibility of ZnO:Cu films deposited between Al2O3 and AlOx-SAOL for NFGM device application was also showed. We applied our ZnO:Cu memory to thin film transistor and evaluate the electrical property. The structure of our memory thin film transistor is consisted of all organic-inorganic hybrid structure. Then, we expect that our film could be applied to high-performance flexible device.----못찾겠음......

• Journal of Educational Research in Mathematics
• /
• v.14 no.1
• /
• pp.39-69
• /
• 2004

This paper investigates the teaching and learning of Linear function relating functional contexts and suggests the improved methods of representation-shift through this analysis. The methods emphasize the link between students' preacquired knowledge of mathematical representations and the way of using those. This methods are explanatory teaching, teaching and teaming based on modelling perspectives or tasks (interpretation, prediction, translation and scaling). We categorize the 8th grade middle school students' errors on the linear function relating real contexts and make a comparative study of the error-remedial effects and the teaching and teaming methods. We present the results of a study in which representation-shift methods based on modelling perspectives and tasks are more effective in terms of flexible connection of representations and error remediation. Also, We describe how students used modelling perspective-taking to explain and justify their conceptual models, to assess the quality of their models and to make connection to other mathematical representation during the problem solving focusing on the students' self-diagnosis.

• Journal of The Korean Society of Integrative Medicine
• /
• v.5 no.3
• /
• pp.83-90
• /
• 2017

Purpose : The purpose of this study was to investigate whether or not the effects of the relationship among college students on the oral health were affected by the increased interest in the appearance. Methods : After explanation of this study, we conducted the questionnaire to those who accepted questionnaire from April 26 to May 28, 2017. In order to collect the data, Naver-form (mobile) questionnaire was distributed to the research subjects and the collected data. The analysis technique used the frequency and percentage to examine the general characteristics of the subjects and the status of the relationship. Chi-square test was used to examine the number of toothbrushes, toothbrushing time, oral health concern, regular oral examination and scaling, use of oral care products, smoking status, and bad breath. Result : Among the total of 190 research subjects, 79 (41.6 %) were male and 111 (58.4 %) were female. The presence of brushing just before going out and carrying a toothbrush were more frequent for those subjects who are in relationship (p<.001). The subjects who considered oral hygiene to be important were higher in those who were in relationship (p<.001). Conclusion : Some oral health care behaviors such as toothbrushing just before going out or carrying a toothbrush were well formed, and oral hygiene was important in those who were in relationship.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.16 no.2
• /
• pp.129-134
• /
• 2005

Background and Objectives : Artecoll(R) is an injectable soft tissue filler, which is a suspension of polymethylmethacrylate microspheres in $3.5\%$ bovine collagen solution. The authors aimed to determine the clinical of Artecoll of Artecoll(R) as an injection material into the vocal fold to correct the glottal insufficiency caused by unilateral vocal cord paralysis. Materials and Methods : Forty-one consecutive patients with unilateral vocal cord paralysis received percutaneous Artecoll injections under local anesthesia. Acoustic, aerodynamic and stroboscopic analyses were prospectively provided before, 1 week and 3 months after injection. Perceptual GRBAS grading by speech language pathologists and subjective ratings of the hoarseness and aspiration by the patients were also obtained. Results : Aerodynamic parameter(maximal phonation time) were significantly improved after the injection (p<0.05). Acoustic parameters (jitter and shimmer) were improved at the 3rd month follow-up. GRBAS uading and patients own subjective scaling of hoarseness and aspiration also showed significant improvement (p<0.05). Early or delayed significant side effects were not observed. Conclusion : Vocal fold injection with Artecoll is a convenient, safe and useful method of temporarily correcting the glottal insufficiency. Further long-term follow-up studies will answer the usefulness and safety of the Artecoll injection laryngoplasty.

• Coupled systems mechanics
• /
• v.4 no.1
• /
• pp.37-65
• /
• 2015

Modeling and simulation of mechanical response of infrastructure object, solids and structures, relies on the use of computational models to foretell the state of a physical system under conditions for which such computational model has not been validated. Verification and Validation (V&V) procedures are the primary means of assessing accuracy, building confidence and credibility in modeling and computational simulations of behavior of those infrastructure objects. Validation is the process of determining a degree to which a model is an accurate representation of the real world from the perspective of the intended uses of the model. It is mainly a physics issue and provides evidence that the correct model is solved (Oberkampf et al. 2002). Our primary interest is in modeling and simulating behavior of porous particulate media that is fully saturated with pore fluid, including cyclic mobility and liquefaction. Fully saturated soils undergoing dynamic shaking fall in this category. Verification modeling and simulation of fully saturated porous soils is addressed in more detail by (Tasiopoulou et al. 2014), and in this paper we address validation. A set of centrifuge experiments is used for this purpose. Discussion is provided assessing the effects of scaling laws on centrifuge experiments and their influence on the validation. Available validation test are reviewed in view of first and second order phenomena and their importance to validation. For example, dynamics behavior of the system, following the dynamic time, and dissipation of the pore fluid pressures, following diffusion time, are not happening in the same time scale and those discrepancies are discussed. Laboratory tests, performed on soil that is used in centrifuge experiments, were used to calibrate material models that are then used in a validation process. Number of physical and numerical examples are used for validation and to illustrate presented discussion. In particular, it is shown that for the most part, numerical prediction of behavior, using laboratory test data to calibrate soil material model, prior to centrifuge experiments, can be validated using scaled tests. There are, of course, discrepancies, sources of which are analyzed and discussed.