• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.45-50
• /
• 2005

Sand pile method, such as sand drain method and sand compaction pile method, has been popularly used as an improved method for soft clay grounds. The effect of accelerating consolidation of soft clay grounds has been evaluated with Barren's solution. The consolidation behavior of soft clay ground with sand piles strongly depends on both the nonlinear mechanical interaction between sand piles and surrounding clays and the degradation permeability of clays. In this paper a method of determining consolidation parameters of soft clay ground with sand drains by using Barren's solution was proposed through a series of numerical simulations. Through the method, the change in both volume compressibility and permeability during consolidation was reasonably evaluated.

• Journal of Navigation and Port Research
• /
• v.29 no.3 s.99
• /
• pp.263-268
• /
• 2005

Laboratory evaluation of the effect of fines, confine stress and dry density on the permeability characteristics in sand columns is presented. The triaxial permeability tests were conducted on different contents of fines(5, 15, 25, $35{\%}$), confine stress ($\sigma_3^'=0.5,\;1.0,\;2.0,\;3.0{\cal}kg/{\cal}cm^2$), and dry density($\gamma_d=1.50,\;1.55,\;1.60,\;1.65{\cal}g{\cal}cm^3$). The results of triaxial permeability tests showed that as the contents of fines, confine stress and dry density became increase permeability became decrease. For the contents of fines, when the fines that smaller than $0.01{\cal}mm$ increases the permeability decreases significantly. For the confine stress and the dry density, the permeability is decreased significantly at changes of the confine stress($\sigma_3^'=0.5{\~}1.0{\cal}kg/{\cal}cm^2$) and the dry density($\gamma_d=1.50{\~}1.55{\cal}g/{\cal}cm^3$) at lower levels.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.1C
• /
• pp.7-16
• /
• 2012

In this paper, using the principle of Static Measurement Methods suggested by Huang (1998), a new experimental device has been made and used in order to calculate the unsaturated permeability of Nak-dong river sand with silt which is an important basic property in the unsaturated soil. This device was designed to measure changes of the unsaturated permeability according to the increase of matric suction. The value of the unsaturated permeability obtained in testing and that obtained using the empirical permeability functional formula were compared and analyzed. As a result, the value of the unsaturated permeability tends to be decreased according to the increase of relative density, silt content and matric suction. This tendency shows it is very closely related to the change of moisture content and void ratio. The empirical permeability functional formula presented by Frelund & Xing (1995) was regarded as the most appropriate model to represent the unsaturated permeability of Nak-dong River silty sand.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.3
• /
• pp.61-70
• /
• 2013

Evaluation of permeability and coefficient of consolidation of clayey sand is critical in analyzing ground stability or environmental problems such as prediction of pollutant transport in groundwater. In this study, permeability tests using a flexible wall permeameter are performed to derive the coefficient of consolidation and permeability of reconstituted soil samples with various mixing ratios of kaolin clays and two different types of sands, which are Jumunjin and Ottawa sands. The test results indicate that the coefficient of consolidation and permeability plots linearly against clay contents in semi-log scale graphs for low clay mixing ratios ranging between 10 to 30%. It is also demonstrated that coefficient of consolidation and permeability of sand and clay mixture are dependent on the soil structure. Contrary to previous findings, the permeability is shown to be independent of the void ratio at low mixing ratios, which can be classified as non-floating fabric. The permeability decreases with the void ratio for floating fabric.

• Journal of Korea Foundry Society
• /
• v.3 no.3
• /
• pp.167-173
• /
• 1983

The effect of sand grain size on the various properties of mold is not only basic but important interest which we have to deal with.And the relation among the various properties of mold (strength, permeability, flowability, compactability, hardness, deformation, toughness etc.) is very complicated and inaccurate, so we can delineate the behavior of mixture (sand+water+bentonite) with experience only. Within recent years a so-called rigid-water theory has been accepted as a means of advancing logical explanations for the research aimed at delineating sand-clay-water relationships. By changing grain size or mesh no. of grain, specimens have been subjected to green compressive strength, permeability, deformation, flowability, compactablity, toughness at room temperature. Under constant mulling energy and ratio of water/bentonite, the results obtained were as follows: 1. With decreasing grain size green compressive strength of the specimen increased. 2. With decreasing grain size permeability decreased. 3. With decreasing grain size flowability and bulk density decreased but compactability increased. 4. With decreasing grain size deformation decreased but toughness increased. 5. At 60 mesh no., the properties of specimen are conspicuously changed. The reason is that the total surface area of sand grain which affects the type of bonding between sand grains is more changed at 60 mesh number.

• Geomechanics and Engineering
• /
• v.4 no.2
• /
• pp.91-103
• /
• 2012

Focusing on the effect of excess pore pressure dissipation on liquefaction-induced ground deformation, a series of 1-g shaking table tests were conducted in a rigid soil container by use of saturated Toyoura sand, the relative density of which was 20-60%. These tests were subjected to the sinusoidal base shaking with step increased accelerations: 100, 200, 300 and 400 Gals for 2-4 seconds. Shaking table tests were done using either water or polymer fluid with more viscous than water, thus varying the sand permeability of model tests. Excess pore pressures, accelerations, settlements and lateral deformations were measured in each test. Test results are presented in this paper and the effect of sand permeability on liquefaction and liquefaction-induced ground deformation was discussed in detail.

• Journal of the Korean Geophysical Society
• /
• v.6 no.3
• /
• pp.131-137
• /
• 2003

In this paper the liquefaction of sand bed under oscillating water pressure are treated as a basic study of the prevention works against the scouring around the hydraulic structures. The results of the former resurch show that the occurrence of the liquefaction depends on both properties of the oscillating water pressure and of the sand layer. Considering the latter properties, that is , the resistivity against the liquefaction increases with the increase of the permeability of the sand bed, we propose the displcement method as one of the prevention works, which is a method to displace the upper layer of the sand bed by the sand with large permeability. The effects of this method are investigated theoretically and experimentally. By the experimental study, it is shown that the proposed displacement method has the apparent effect to prevent the liquefaction. The experimental results are explained fairly well by the theoretical analysis based on the theory of the flow through the elastic porous media.

• International Journal of Concrete Structures and Materials
• /
• v.19 no.1E
• /
• pp.17-23
• /
• 2007

In rainy weather, permeable concrete pavement has advantages such as good drainage, increased skid resistance, reduced splash and spray behind vehicles for improving the safety of driving vehicles as well as reduction of the traffic noise. It also contributes to improvement of traffic environment. In this study, the fundamental properties of permeable concrete in accordance with maximum size of aggregate, sand percentage and unit cement content were investigated for practical use of permeable concrete pavement. Although the permeability standard for typical permeable asphalt-concrete pavement is $1{\times}10^{-2}cm/sec$, the researchers determined that the coefficient of permeability of the permeable concrete should be set higher at $1{\times}10^{-1}cm/sec$. Then, the researchers measured the coefficient of permeability, strength, void ratio, and continuous void ratio of the permeable concrete while varying maximum size of the aggregate, sand percentage, unit cement content for detailed analysis. It was found that the void ratio, continuous void ratio, and flexural strength were about 15%, 12%, and 5.0MPa, respectively, when the permeability of the concrete was set at $1{\times}10^{-1}cm/sec$. Given that the maximum size of aggregate was $10{\sim}13mm$, we reached the conclusion that the best mix design for permeable concrete was $0{\sim}20%$ of sand percentage and $380kg/m^3$ of unit cement content.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.1
• /
• pp.75-82
• /
• 2004

To evaluate the characteristics of permeability in weathered residual soil, flexible wall permeameter tests are performed using undisturbed samples. The Influence of hydraulic gradient and confining pressure on the permeability of weathered residual soil is analyzed. To compare the characteristics of permeability between weathered soil and sand, similar tests are performed using Jumoonjin sand. Also, piping model tests are performed to investigate the piping resistance of weathered residual soil. As a result, weathered residual soil shows very dependable permeability on hydraulic gradient and very large resisting ability against piping compared with sand.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.227-230
• /
• 1998

The void ratio, continuous void ratio, coefficient of permeability, compressive strength and tensile strength were considered according to the EAF(Electric Arc Furnace) slag replacement and sand percentage in permeable concrete used with EAF slag as aggregate. The sand percentage was directly proportional to the permeable coefficient, but inversely proportional to the compressive strength. When the compressive strength and coefficient of permeability were 230 kg/$\textrm{cm}^2$ and 1$\times$$10^{-1}$ cm/sec, the useful sand percentage was 8%. When the EAF slag replacement was 25%, the coefficient of permeability was the most low and compressive strength was the most high.