• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.90-91
• /
• 2014

In this study, the effect of very fine sand on drying shrinkage cracking of concrete was experimentally evaluated. As a result of the study, the time-to-cracking of concrete used very fine sand was shorter than plain concrete. Also, the stress rate of concrete used very fine sand was higher than plain concrete. It was due to the increase of water content when very fine sand was used in concrete. In conclusion, the use of very fine sand can lead the increase of water content to meet the target slump and higher potential of cracking of concrete.

• International Journal of Concrete Structures and Materials
• /
• v.6 no.1
• /
• pp.59-64
• /
• 2012

Sand-concrete is being researched for potential usage in construction in Saharan regions of Algeria, because of shortage in coarse aggregate resources. This research work deals with the effect of dune sand, available in huge quantities in these regions, on the properties of flowing sand-concrete (FSC) prepared with different proportions of dune and river sands. Mini-cone slump test, v-funnel flow-time test and viscosity measurements were used to characterize the behaviour of FSC in fresh state. The 28-day compressive strength was also determined. Test results show that an optimal content of dune sand, which makes satisfied fresh and hardened properties of FSC, is obtained. Moreover, the obtained flow index (constant b) calculated by the help of power-law viscosity model is successfully correlated to the experimental results of v-funnel flow time.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.58-63
• /
• 1996

The waste foundry sand might be recycled in concrete, resulting in energy saving and environmental protection. An half Factorial Exprements were performed with the variables of W/C ratio, S/A, Sand/Waste foundry sand ratio and Slump as a preliminary study for optimum mix design of concrete. The results show that the W/C ratio is the most important factor to the concrete strength. The substitute of waste foundry sand up to 30% has little influence, saying that it can substitute the fine aggregate without damaging the concrete properties.

• Journal of the Korea Concrete Institute
• /
• v.12 no.1
• /
• pp.89-99
• /
• 2000

The objective of this study is to investigate the bond strength properties of antiwashout underwater concrete. The arrangement of bars (vertical bar, horizontal upper bar, horizontal lower bar), condition of casting and curing (fresh water, sea water), type of fine aggregate (river sand, blended sand(river sand : sea sand = 1:1), and proportioning strength of concrete (210, 240, 270, 300, 330kgf/$\textrm{cm}^2$)are chosen as the experimental parameters. The test results(ultimate bond stress) are compared with bond and development provisions of the ACI Building Code(ACI 318-89) and proposed equations from previous research(which was proposed by Orangun et. al). The experimental results show that ultimate bond stress of antiwashout underwater concrete which arranged bar on the horizontal lower, used the blend sand, and was cast and cured in the fresh water are higher that other conditions. The ultimate bond stress were increased in proportion to {{{{( SQRT {fcu }) }}3 2. From this study, rational analytic formula for the ultimate bond stress are to be from compressive strength of concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2004.05a
• /
• pp.15-20
• /
• 2004

To the development on reusing method of the heat-source waste at Daegu Bisan dyeing-complex, this study is aimed to application of it's crushing material (hereafter waste sand) as concrete fine aggregate. The results are as follows; 1. Flow and unit weight of mortar using waste sand as concrete fine aggregate are decreased. 2. At the results of compressive strength test and bending strength test, mortar using waste sand superior to plain mortar within 80％ substitute ratio of waste sand. Because increasing rate of compressive strength is similar through increasing age, waste sand performs as filler's function of no-effect with cement only. 3. At the results of concrete application test, unit weight of concrete using waste sand is similar to plain concrete and compressive strength of concrete is superior to plain likewise the results of mortar test

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.52-57
• /
• 1999

The aimed of this study is to analyze the qualities of foundry waste sand and the basic physic of the concrete mixed with the foundry waste sand, as a way of study for reusing the foundry waste sand disused in the foundry as the fine aggregate for concrete. According to the experimental results, the foundry waste sand is composed of silica ore whose main ingredient is SiO2 and doesn't produce harmful objects of hydration reaction, and the fluidity of concrete shows a decline with the increase of replacement ratio of foundry waste sand, and the compress strength, the tensile strength, the elastic modulus of concrete containing foundry waste sand are improved at the replacement rate of 25%.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.1 s.15
• /
• pp.63-68
• /
• 2005

Generally, aggregate may limit the workability, strength and durability of concrete, and good concrete cannot be made with aggregate of bad property including low strength, bad shape and grading. But recently, it has been insufficient in quantity to collect good natural aggregate because of exhaustion of aggregate resources. In case of Korea, the using ratio of crushed stone occupies about 97 percent of total coarse aggregate, and ratio of crushed sand occupies about 18.3 percent of total fine aggregate. This is an experimental study to compare and analyze the properties of crushed sand for concrete in capital region and concrete according to the replacement ratio of crushed sand to improve quality and mix design of concrete using crushed sand. According to test results, it was found that nearly all the properties of crushed sand satisfied with the value recommended by KS. And it is recommended that FM of crushed sand should be lowered by improvement of manufacture system or grading adjustment should be used because FM of crushed sand was a bit higher.

• Advances in concrete construction
• /
• v.16 no.4
• /
• pp.177-188
• /
• 2023

In the context of the shortage of river sand, two types of manufactured sand (MS) were used to partially replace river sand (RS) to design manufactured sand concrete (MSC). A total of 81 specimens were designed for uniaxial compression test and beam flexure test. Two parameters were considered in the tests, including the types of MS (i.e. limestone manufactured sand (LMS), pebble manufactured sand (PMS)) and the MS replacement percentage (i.e., 0%, 25%, 50%, 75%, 100%). The stress-strain curves of MSC were obtained. The effects of these parameters on the compressive strength, elastic modulus, peak strain, toughness and flexural strength were discussed. Additionally, the sensitivity of particle size distributions to the performance of MSC was evaluated based on the grey correlation analysis. The results showed that compared with river sand concrete (RSC), the rising slope of the stress-strain curves of limestone manufactured sand concrete (LMSC) and pebble manufactured sand concrete (PMSC) were higher, the descending phrase of LMSC were gentle but that of PMSC showed an opposite trend. The physical and mechanical properties of MSC were affected by the MS replacement percentage except the compressive strength of PMSC. When the replacement percentage of LMS and PMS were 50% and 25% respectively, the corresponding performances of LMSC and PMSC were better. In generally, when the replacement percentage of LMS and PMS were same, the comprehensive performance of LMSC were better than that of PMSC. The constitutive model and the equations for mechanical properties were proposed. The influence of particle ranging from 0.15 mm to 0 mm on the performance of MSC was lower than particle ranging from 4.75 mm to 0.15 mm but this influence should not be ignored.

• International conference on construction engineering and project management
• /
• 2024.07a
• /
• pp.383-390
• /
• 2024

Sand is a vital component within a concrete admixture for variety of structures and is classified as one of the crucial bulk material used. Assessing the Fineness Modulus (FM) of sand is an essential part of concrete production process because FM significantly affects the workability, cost-effectiveness, porosity, and concrete strength. Traditional sand quality inspection methods, like Sieve Analysis Test, are known to be laborious, time-consuming, and cost ineffective. Previous studies had mainly focused on measuring the physical characteristics of individual sand particles rather than real-time quality assessment of sand, particularly its FM during concrete production. This study introduces an image-based method for detecting flawed sand through deep learning techniques to evaluate the quality of sand used in concrete. The method involves categorizing sand images into three groups (Unavailable, Stable, Dangerous) and seven types based on FM. To achieve a high level of generalization ability and computational efficiency, various deep learning architectures (VGG16, ResNet-101 and MobileNetV3 small), were evaluated and chosen; with the inclusion of transfer learning to ensure model accuracy. A dataset of labeled sand images was compiled. Furthermore, image augmentation techniques were employed to effectively enlarge this dataset. The models were trained using the prepared dataset that were categorized into three discrete groups. A comparative analysis of results was performed based on classification performance metrics which identified the VGG16 model as the most effective achieving an impressive 99.87% accuracy in identifying flawed sand. This finding underscores the potential of deep learning techniques for assessing sand quality in terms of FM; positioning this research as a preliminary investigation into this topic of study.

• Journal of the Korea Concrete Institute
• /
• v.18 no.3 s.93
• /
• pp.415-423
• /
• 2006

As the shortage of natural & good quality aggregate for concrete, it is needed development of alternative aggregate. At the present time, the crushed sand is widely used among the alternation aggregate, and the usage of crushed sand will be increased more and more. Generally, crushed sud is produced with wet process in domestic, but some manufacturing companies which are handicapped with local restrict are produced by dry process. In this study, analyzing the facilities of dry crushed sand, the quality properties of dry crushed sand was done by Korean Industrial Standards. Based on the quality results of dry crushed sand, the experiment of concrete with the dry crushed sand which is substitute for sea sand was done. As the results of basic qualities, the amount of 0.08 mm sieve passing ratio was over KS criteria, and the fineness modulus was higher than sea sand, and the other physical properties of dry crushed sand was similar to sea sand. The results of concrete experiment, according to the substitutive ratio of dry crushed sand is increased, the slump and air content of concrete was decreased by increase of fine particles of dry crushed sand, and the unit weight content, compressive & tensile strength of concrete were increased on the contrary. The physical properties of concrete used dry crushed sand were showed same tendency without relation to W/B. Consequently, if the fine particle contents of dry crushed sand was lower, it is judged that dry crushed sand is no problem to use for concrete aggregate and the amount of usage will be increased.