• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.5
• /
• pp.159-168
• /
• 2010

This study investigates the relationships between the maximum freshwater pumping discharge and hydraulic properties of coastal aquifer using a laboratory model. The experiment performed the fresh pumping test in various locations near the saltwedge induced by saltwater intrusion to freshwater over aquifer characteristics of hydraulic conductivity, salinity, and ground surface slope. Saltwater pumping also tested to protest saltwater intrusion to the excessively discharging freshwater well. The maximum freshwater discharges were achieved, and then the optimum saltwater discharges were measured. It is found that greater hydraulic conductivity and ground surface slope produced greater the maximum freshwater pumping discharge. Salinity gave less impact on the pumping discharge relatively. Higher freshwater discharge was found at higher hydraulic conductivity and steeper ground surface slope. The optimum saltwater discharge required 14% more pumping rate than the maximum freshwater discharge to keep saltwater intrusion to the freshwater pumping well. Pumping well located closer to salt-wedge profile promoted less freshwater pumping discharge. Therefore, pumping well location, hydraulic conductivity, ground surface slope, and salinity should be taken into account in freshwater pumping in coastal aquifer.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.6
• /
• pp.492-499
• /
• 2009

Effect of drip irrigation on soil salinity control and growth of vegetable crops was studied in the three reclaimed lands of Korea in 2007. Drip irrigation was done one or two times per month for reduction of salt stress by using vinyl hose with tiny holes laid on ridge surface under black plastic film mulch during growing season of cabbage and chinese cabbage. It was observed that drip irrigation was generally effective to soil salinity control, but soil salinity variation of some place was not fully solved to lower down under level of free salt stress. It is also considered that high salinity of runoff water spilled out from cultivation ridge plays another key role for soil salinity management. Consequentially, this soil salinity variation might be one of factors brought low average yield and low commercial ratio of agricultural products. Relation between soil salinity and head growth of cabbage and chinese cabbage was well expressed as logarithmic function. Surface soil EC to reach at 50% of growth reduction to the heaviest head can be estimated was $6.1dS^{\circ}{\S}m^{-1}$ for cabbage and $5.7dS\;m^{-1}$ for chinese cabbage transplanted at optimum season.

• Journal of Forest and Environmental Science
• /
• v.14 no.1
• /
• pp.24-47
• /
• 1998

This study examined ecophysiological characteristics, cultivation methods and planting uses of tree and shrub species native to Kangwon province and valuable as landscape plants. The results were as followos : 1. 73 species selected as shrubs were ; Rhododendron brachycarpum, Rhododendron micranthum, Abelia mosanensis, Abeliophyllum distichum, Acanthopanax sessiliflorus, Acanthopanax senticosus, Alangium platanifolium var. macrophyllum etc. 2. 38 species selected as trees were ; Cornus controversa, Sorbus commixta, Malus baccata, Prunus padus, Acer triflorum, Acer tegmentosum, Styrax japonica, Styrax obassia, Sorbus alnifolia etc. 3. Shade-tolerant species were ; Abies koreana, Rhododendron brachycarpum, Rhododendron micranthum, Prunus padus, Sorbus commixta, Acer triflorum, Rhus japonica, Cornus kousa, Kalopanax pictus, Chionanthus retusa, Sorbus alnifolia, Magnolia sieboldii, Sorbaria sorbifolia var. stellipila, Berberis koreana, Lindera obtusiloba, Rhododendron schlippenbachii and Euonymus alatus. 4. Species growing well even in less fertile soils were ; Pinus thunbergii, Quercus dentata, Koelreuteria paniculata, Rhus japonica, Quercus acutissima, Albizzia julibrissin, Sorbus alnifolia, Staphylea bumalda, Philadelphus schrenckii, Clerodendron trichotomum, Deutzia coreana, Weigela florida, Zanthoxylum schinifolium and Lindera obtusiloba. 5. Salt-tolerant species were ; Pinus thunbergii, Quercus aliena, Prunus padus, Styrax japonica, Quercus dentata, Kalopanax pictus, Chionanthus retusa, Albizzia julibrissin, Tilia amurensis, Forsythia koreana, Lonicera maackii, Symplocos chinensis for. pilosa, Clerodendron trichotomum, Sambucus williamsii var. coreana, Abelia mosanensis, Deutzia coreana, Viburnum carlesii, Rhus japonica, Rhododendron yedoense var. poukhanense, Zanthoxylum schinifolium, Callicarpa dichotoma, Rhododendron schlippenbachii and Euonymus alatus. 6. Pollutant-tolerant species were ; Styrax japonica, Prunus padus, Quercus dentata, Kalopanax pictus, Chionanthus retusa, Gleditsia japonica var. koraiensis, Styrax obassia, Forsythia koreana, Kpiraea salicifolia, Clerodendron trichotomum, Viburnum sargentii, Viburnum carlesii, Weigela florida and Rhododendron yedoense var. poukhanense.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.10
• /
• pp.81-92
• /
• 2011

The rheological properties of Wyoming bentonites are strongly influenced by the size of particles, cation exchangeable capacity, arrangement and morphology of clay mineral. This paper presents the results of rheological investigations on the Wyoming bentonites aqueous dispersions: two types of particle flocculation were considered. For the Wyoming bentonite, 0g/L and 30g/L NaCl equivalent salinity were added in fresh and salt water to examine the rheological behavior. This paper examined the general rheological characteristics, compatibility of rheological models and correlation between soil structure and change in rheological properties of Wyoming bentonite caused by increasing salinity. From flow curves of bentonites hydrated with fresh water and salt water, the observed general flow behavior is very close to shear thinning with yield stress (or ideal Bingham fluid with yield stress and plastic viscosity). However, the change of shear stress at the same shear rate is clear, particularly for lower shear rate. Well-known rheological models are used to fit the data. There is a good agreement between rheological model and data: Carreau, Herschel-Bulkley and power-law for S=0g/L and bilinear, Herschel-Bulkley and power-law for S=30g/L. It may be due to the fact that the internal structural bonding (strong modification of particle-particle interactions from edge-to-edge and/or edge-to-face to face-to-face) in soil matrix is affected from the evolution of rheological properties with different salinities.

• Clean Technology
• /
• v.22 no.3
• /
• pp.175-180
• /
• 2016

Tyrosinases catalyze the hydroxylation of a monophenol (monophenolase activity) and the conversion of an o-diphenol to o-quinone (diphenolase activity), which are mainly involved in the modification of tyrosine residues into 3,4-dihydroxyphenyl-alanine (DOPA) and DOPA/DOPAquinone-derived intermolecular cross-linking. Previously, we obtained a slightly acidic and cold-active tyrosinase, tyrosinase-CNK, by our recombinant protein approach. The enzyme showed optimal activity at pH 6.0 and 20 ℃ with an abnormally high monophenolase/diphenolase activity ratio and still had approximately 50% activity compared with the highest activity even in ice water. Here, we investigated reaction stability of the recombinant tyrosinase-CNK as a psychrophilic enzyme. The enzyme showed remarkable thermal stability at 0 ℃ and the activity was well conserved in repeated freeze-thaw cycles. Although water-miscible organic solvent as reaction media caused the activity decrease of tyrosinase-CNK as expected, the enzyme activity was not additionally decreased with increased concentration in organic solvents such as ethanol and acetonitrile. Also, the enzyme showed high salt tolerance in chaotropic salts. It was remarkably considered that 2⁺ metal ions might inhibit the incorporation of Cu²⁺ into the active site. We expect that these results could be used to design tyrosinase-mediated enzymatic reaction at low temperature for the production of catechols through minimizing unwanted self-oxidation and enzyme inactivation.

• Membrane Journal
• /
• v.27 no.3
• /
• pp.240-247
• /
• 2017

In this study, the heterogeneous ion exchange membranes prepared by the combination of the carbon electrode and mixed the cation and anion exchange polymers and polyvinylidene fluoride as the basic polymer together were made to recognize the efficiency of the salt removal for the application of the membrane capacitive deionization process. The mixing weight ratio of the solvent, basic polymer and ion exchange resin was 7 : 2 : 1 and this mixed solution was directly cast on the electrode. As for the operating conditions of the adsorption voltage and time, feed flow rate, desorption voltage and time of the feed solution NaCl 100 mg/L, the salt removal efficiencies (SRE) were measured. Apart from this NaCl, the $CaCl_2$ and $MgSO_4$ solutions were investigated in terms of SRE as well. Typically, SRE for NaCl 100 mg/L solution under the conditions of adsorption voltage/time, 1.5 V/3 min, desorption voltage/time -0.1 V/3 min, was shown 98%. And for the $CaCl_2$ and $MgSO_4$ solutions, the SREs of 70 and 59% were measured under the conditions of adsorption voltage/time, 1.2 V/3 min, desorption voltage/time -0.5 V/5 min, respectively.

• KSBB Journal
• /
• v.7 no.4
• /
• pp.296-301
• /
• 1992

A Pseudomonas fluorescens was selected from mushrooms and studied in both batch and fed-batch cultures in order to get maximal biomass concentration. P. fluorescens is an aerobic bacterium and antagonistic to Pseudomonas tolaasii which causes blotch disease on the mushroom cap. P fluarescens and P. tolaasii were identified by Gram staining, gelatin liquefaction, oxidase test, etc. and were characterized by pigment production, temperature sensitivity, salt tolerance and rapid pitting test, etc., Celts of P. fluorescens well in medium containing 30g/L of glucose, whereas the growth was inhibited at the glucose levels at higher than 30g/L. The highest values of specific growth rate and productivity were obtained when using 10g/1 of yeast extract. Optimum concentrations of $NH_4Cl$ and ${(NH_4Cl)}_2SO_4$ for culture were found to be 1.0g/L and 0.1g/L respectively. Optimum concentration of $MgSO_4{\cdot}7H_2O$ used as a sulfursource was 1.0g/L. It was also found that the cell concentrations reached the maximum level when grown on the medium containing 1.0g/L of $KH_2PO_4$ and 0.1g/L of $CaCl_2$. Also, the optimum culture conditions were $30^{\circ}C$ and pH 6.0. Cultivation of P. fluarescens at high dissolved oxygen (DO) concentration led to a decrease of bacterial productivity in batch culture. Maximum productivity was achieved at 40% DO concentration.

• Journal of the Korea Convergence Society
• /
• v.9 no.4
• /
• pp.151-160
• /
• 2018

Waxes currently used as a coating material to preserve surfaces of outdoor iron sculptures tend to face lower coating strength and efflorescence due to the aging from air pollution and acid rains. Consequently, they are subjected to repeated corrosions shortly after the treatment. And the sculptures face the problem losing their original nature because of the changes of colors and lusters, so this convergence study aims at developing wax with better performance than the existing materials. For this reason, the study identified the effects of physical property using the environmental experiments such as the tests of salt spray and gas corrosion as well as the analysis of luster level and thermo-gravimetry. As this study result, the developed ISC wax showed the excellent blocking effect from salt water and coating durability more than five times compared with the existing waxes, better acid resistance by two-four times, sun block effect by 2-10 times, improved luster variance by 3-16 times, improved thermo-stability and durability by 0.5-5 times, and therefore demonstrating far better coating effect than the existing waxes. In the light of these findings, this study contributes for this new development which can replace the existing waxes used so far in order to preserve the outdoor iron sculptures.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.2
• /
• pp.198-202
• /
• 1997

Jangkimchi is a kind of Kimchi which is made with soy-sauce instead of salt. Occasionally, when sugar is added to Jangkimchi for condiment, the kimchi juice becomes viscous. In this study. the nature of the viscous material and the condition for producing viscous property in Kimchi juice were investigated. HPLC analysis showed that the viscous material in Jangkimchi is polysaccharide composed of glucose. Sucrose was more effective in forming viscous juice than glucose and the viscosity increased with the addition of sucrose up to 10%. Soy-sauce also played a role in increasing the viscosity of Kimchi juice compared with salt. Aerobic fermentation condition was found to be another factor to make the juice viscous. The population of Leuconostoc mesenteroides, well-known producer of viscous dextran was not different in the Kimchi juice prepared with the addition of sucrose from that without sucrose, which implys that the Jangkimchi preparation methods such as addition of sucrose and soy-sauce would do some effects on the production of viscous material in Jangkimchi.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.8
• /
• pp.664-669
• /
• 2012

Nano-structured one-dimensional $Na_2Ti_6O_{13}$ particles were synthesized by a molten salt process. Effects of processing parameters on the microstructure and band gap energy of the $Na_2Ti_6O_{13}$ powder were studied in this paper. For the synthesis of the $Na_2Ti_6O_{13}$ particles, two different raw materials of tubular shaped Na-titanate (Na-TiNT) and spherical shaped $TiO_2$ were utilized. Synthesizing with the raw material of Na-TiNT, around 70nm thick 1D-$Na_2Ti_6O_{13}$ with the bandgap energy of 3.5 eV was obtained at $810^{\circ}C$. Below $810^{\circ}C$ or without the presence of NaCl, 1D-$Na_2Ti_6O_{13}$ was in a relatively short in length and agglomerated state. With the processing temperature increased, the thickness of the 1D-$Na_2Ti_6O_{13}$ was also observed to be increased. On the other hand, when $TiO_2$ was employed as a raw material, the mixed amount of $Na_2CO_3$ played an important role in transforming the morphology and phase of the raw material, affecting the bandgap energy of the synthesized product. Specific surface area of the synthesized 1D-$Na_2Ti_6O_{13}$ was significantly affected by the raw and mixed materials as well as processing temperature. When Na-TiNT was processed at $810^{\circ}C$ with NaCl, the specific surface area of the 1D-$Na_2Ti_6O_{13}$ showed the best value of 30.63 $m^2/g$.