• Economic and Environmental Geology
• /
• v.55 no.2
• /
• pp.209-217
• /
• 2022

The purpose of this study was to confirm the dissolution of arsenic from the stabilized soil around abandoned coal mines by cultivation activities. Experimental soils were collected from the agricultural field around Okdong and Buguk coal mines, and the concentration of arsenic in the soil and the geochemical mobility were confirmed. The average arsenic concentration was 20 mg/kg. The soil with relatively high geochemical mobility of arsenic in the soil was used in the batch and column experiment. The limestone was mixed with soil for soil stabilization, and the mixing ratio was 3% of limestone, based on the soil weight. The phosphoric acid fertilizer (NH₄H₂PO₄) was added to the soil to simulate a cultivation condition according to the Rural Development Administration's rules. Comparative soil without mixing limestone was prepared and used as a control group. The arsenic extraction from soil was increased following the fertilizer mixing amount and it shows a positive relationship. The concentration of phosphate in the supernatant was relatively low under the condition of mixing limestone, which is determined to be result of binding precipitation of phosphate ions and calcium ions dissolved in limestone. Columns were set to mix phosphoric acid fertilizers and limestone corresponding to cultivation and stabilization conditions, and then the column test was conducted. The variations of arsenic extraction from the soil indicated that the stabilization was effectible until 10 P.V.; however, the stabilization effect of limestone decreased with time. Moreover, the geochemical mobility of arsenic has transformed by increasing the mobile fractions in soil compared to initial soil. Therefore, based on the arsenic extraction results, the cultivation activities using phosphoric fertilizer could induce a decrease in the stabilization effect.

• Journal of Biomedical Engineering Research
• /
• v.6 no.2
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• Journal of Intelligence and Information Systems
• /
• v.23 no.3
• /
• pp.119-138
• /
• 2017

Recently, SNS has become an important channel for marketing as well as personal communication. However, cybercrime has also evolved with the development of information and communication technology, and illegal advertising is distributed to SNS in large quantity. As a result, personal information is lost and even monetary damages occur more frequently. In this study, we propose a method to analyze which sentences and documents, which have been sent to the SNS, are related to financial fraud. First of all, as a conceptual framework, we developed a matrix of conceptual characteristics of cybercriminality on SNS and emergency management. We also suggested emergency management process which consists of Pre-Cybercriminality (e.g. risk identification) and Post-Cybercriminality steps. Among those we focused on risk identification in this paper. The main process consists of data collection, preprocessing and analysis. First, we selected two words 'daechul(loan)' and 'sachae(private loan)' as seed words and collected data with this word from SNS such as twitter. The collected data are given to the two researchers to decide whether they are related to the cybercriminality, particularly financial fraud, or not. Then we selected some of them as keywords if the vocabularies are related to the nominals and symbols. With the selected keywords, we searched and collected data from web materials such as twitter, news, blog, and more than 820,000 articles collected. The collected articles were refined through preprocessing and made into learning data. The preprocessing process is divided into performing morphological analysis step, removing stop words step, and selecting valid part-of-speech step. In the morphological analysis step, a complex sentence is transformed into some morpheme units to enable mechanical analysis. In the removing stop words step, non-lexical elements such as numbers, punctuation marks, and double spaces are removed from the text. In the step of selecting valid part-of-speech, only two kinds of nouns and symbols are considered. Since nouns could refer to things, the intent of message is expressed better than the other part-of-speech. Moreover, the more illegal the text is, the more frequently symbols are used. The selected data is given 'legal' or 'illegal'. To make the selected data as learning data through the preprocessing process, it is necessary to classify whether each data is legitimate or not. The processed data is then converted into Corpus type and Document-Term Matrix. Finally, the two types of 'legal' and 'illegal' files were mixed and randomly divided into learning data set and test data set. In this study, we set the learning data as 70% and the test data as 30%. SVM was used as the discrimination algorithm. Since SVM requires gamma and cost values as the main parameters, we set gamma as 0.5 and cost as 10, based on the optimal value function. The cost is set higher than general cases. To show the feasibility of the idea proposed in this paper, we compared the proposed method with MLE (Maximum Likelihood Estimation), Term Frequency, and Collective Intelligence method. Overall accuracy and was used as the metric. As a result, the overall accuracy of the proposed method was 92.41% of illegal loan advertisement and 77.75% of illegal visit sales, which is apparently superior to that of the Term Frequency, MLE, etc. Hence, the result suggests that the proposed method is valid and usable practically. In this paper, we propose a framework for crisis management caused by abnormalities of unstructured data sources such as SNS. We hope this study will contribute to the academia by identifying what to consider when applying the SVM-like discrimination algorithm to text analysis. Moreover, the study will also contribute to the practitioners in the field of brand management and opinion mining.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.39 no.4
• /
• pp.10-23
• /
• 2021

During the Japanese colonial period, the palaces of Joseon were damaged in many parts. Changgyeonggung Palace is the most demolished palace with the establishment of a zoo, botanical garden, and museum. During the Japanese colonial period, the palaces of Joseon were damaged in many parts. This study examined the construction process of Jangseogak(Yi Royal-Family Museum), located right next to the Jagyeongjeon site, which was considered the most important space in the Changgyeonggung residential area of royal family zone, through historical materials and field research. Built in 1911, Jangseogak is located at a location overlooking the entire Changgyeonggung Palace and overlooking the Gyeongseong Shrine of Namsan in the distance. Changes in the surrounding space during the construction of Jangseogak can be summarized as follows. First, in the early 1910s, the topography of the garden behind Jagyeongjeon and part of the Janggo were damaged to create the site of Jangseogak. The front yard was built in the front of Jangseogak, and a stone pillar was installed, and a staircase was installed to the south. In the process, the original stone system at the rear of Yanghwadang was destroyed, and it is presumed that Jeong Iljae and other buildings were demolished. Second, in the 1920s, many pavilions were demolished and the zoo and botanical gardens and museums were completed through leveling. After the Jangseogak was completed, the circulation of the Naejeon and surrounding areas was also changed. Cherry trees and peonies were planted in the flower garden around the front yard of Jangseogak and the stairs, and a Japanese-style garden was created between Yanghwadang and Jibbokheon. Third, in the 1930s, the circulation around Jangseogak was completed in its present form, and the museum, Jangseogak, Zoological and Botanical Gardens, and Changgyeonggung, which became a cherry tree garden, were transformed into a Japanese-style cultural park. After that, the surrounding space did not change much until it was demolished. The restoration of the present palace is a long-term, national project of the Cultural Heritage Administration. The results of this study will provide important data for the restoration plan of Changgyeonggung Palace in the future, and it is expected that it will provide additional information to related researchers in the future.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.3
• /
• pp.40-46
• /
• 2009

The applicability of a well-type autotrophic sulfur-oxidizing reactive barrier (L $\times$ W $\times$ D = $3m\;{\times}\;4\;m\;{\times}\;2\;m$) as a long-term treatment option for nitrate removal in groundwater was evaluated. Pilot-scale (L $\times$ W $\times$ D = $8m\;{\times}\;4\;m\;{\times}\;2\;m$) flow-tank experiments were conducted to examine remedial efficacy of the well-type reactive barrier. A total of 80 kg sulfur granules as an electron donor and Thiobacillus denitrificans as an active bacterial species were prepared. Thiobacillus denitrificans was successfully colonized on the surface of the sulfur granules and the microflora transformed nitrate with removal efficiency of ~12% (0.07 mM) for 11 days, ~24% (1.3 mM) for 18 days, ~45% (2.4 mM) for 32 days, and ~52% (2.8 mM) for 60 days. Sulfur granules attached to Thiobacillus denitrificans were used to construct the well-type reactive barrier comprising three discrete barriers installed at 1-m interval downstream. Average initial nitrate concentrations were 181 mg/L for the first 28 days and 281 mg/L for the next 14 days. For the 181 mg/L (2.9 mM) plume, nitrate concentrations decreased by ~2% (0.06 mM), ~9% (0.27 mM), and ~15% (0.44 mM) after $1^{st}$, $2^{nd}$, and $3^{rd}$ barriers, respectively. For the 281 mg/L (4.5 mM) plume, nitrate concentrations decreased by ~1% (0.02 mM), ~6% (0.27 mM), and ~8% (0.37 mM) after $1^{st}$, $2^{nd}$, and $3^{rd}$ barriers, respectively. Nitrate plume was flowed through the flow-tank for 49 days by supplying $1.24\;m^3/d$ of nitrate solution. During nitrate treatment, flow velocity (0.44 m/d), pH (6.7 to 8.3), and DO (0.9~2.8 mg/L) showed little variations. Incomplete destruction of nitrate plume was attributed to the lack of retention time, rarely transverse dispersion, and inhibiting the activity of denitrification enzymes caused by relatively high DO concentrations. For field applications, it should be considered increments of retention time, modification of well placements, and intrinsic DO concentration.

• Journal of Intelligence and Information Systems
• /
• v.16 no.3
• /
• pp.77-97
• /
• 2010

Market timing is an investment strategy which is used for obtaining excessive return from financial market. In general, detection of market timing means determining when to buy and sell to get excess return from trading. In many market timing systems, trading rules have been used as an engine to generate signals for trade. On the other hand, some researchers proposed the rough set analysis as a proper tool for market timing because it does not generate a signal for trade when the pattern of the market is uncertain by using the control function. The data for the rough set analysis should be discretized of numeric value because the rough set only accepts categorical data for analysis. Discretization searches for proper "cuts" for numeric data that determine intervals. All values that lie within each interval are transformed into same value. In general, there are four methods for data discretization in rough set analysis including equal frequency scaling, expert's knowledge-based discretization, minimum entropy scaling, and na$\ddot{i}$ve and Boolean reasoning-based discretization. Equal frequency scaling fixes a number of intervals and examines the histogram of each variable, then determines cuts so that approximately the same number of samples fall into each of the intervals. Expert's knowledge-based discretization determines cuts according to knowledge of domain experts through literature review or interview with experts. Minimum entropy scaling implements the algorithm based on recursively partitioning the value set of each variable so that a local measure of entropy is optimized. Na$\ddot{i}$ve and Booleanreasoning-based discretization searches categorical values by using Na$\ddot{i}$ve scaling the data, then finds the optimized dicretization thresholds through Boolean reasoning. Although the rough set analysis is promising for market timing, there is little research on the impact of the various data discretization methods on performance from trading using the rough set analysis. In this study, we compare stock market timing models using rough set analysis with various data discretization methods. The research data used in this study are the KOSPI 200 from May 1996 to October 1998. KOSPI 200 is the underlying index of the KOSPI 200 futures which is the first derivative instrument in the Korean stock market. The KOSPI 200 is a market value weighted index which consists of 200 stocks selected by criteria on liquidity and their status in corresponding industry including manufacturing, construction, communication, electricity and gas, distribution and services, and financing. The total number of samples is 660 trading days. In addition, this study uses popular technical indicators as independent variables. The experimental results show that the most profitable method for the training sample is the na$\ddot{i}$ve and Boolean reasoning but the expert's knowledge-based discretization is the most profitable method for the validation sample. In addition, the expert's knowledge-based discretization produced robust performance for both of training and validation sample. We also compared rough set analysis and decision tree. This study experimented C4.5 for the comparison purpose. The results show that rough set analysis with expert's knowledge-based discretization produced more profitable rules than C4.5.

• Journal of the Korean Academy of Child and Adolescent Psychiatry
• /
• v.14 no.2
• /
• pp.139-149
• /
• 2003

Objectives：To review the history of the development and current status of Korean Child and Adolescent Psychiatry and to propose the future tasks at this 20th anniversary of Korean Academy of Child and Adolescent Psychiatry. Methods：Records and publications of Korean Academy, personal communications with senior members of the Academy, the author's recollections and memoirs. Results：Korean Child Psychiatry started with opening Child Psychiatry Clinic at Seoul National University Hospital in 1979 and establishing Division of Child and Adolescent Psychiatry at the same hospital in 1980. A Child Psychiatry Study Group was formed in 1983 and it transformed into Korean Academy of Child and Adolescent Psychiatry in 1986. In the past 20 years, Korean child and adolescent psychiatry made an impressive progress and contributed significantly to the development of Korean medicine as well as to the establishment of child mental health service. There are 77 board-certified and 48 board-eligible child psychiatrists, and 18 child psychiatry fellows are in training as of 2003. Main forces of this successful introduction of child psychiatry are 1) 7 child psychiatry training centers at major university hospitals, 2) publication of Korean Journal of Child and Adolescent Psychiatry in 1990, 3) the establishment child psychiatry board certification system in 1996. Korean child psychiatry has extended its role in the international child psychiatry and took leadership in establishing Asian Society of Child and Adolescent Psychiatry and Allied Professions(ASCAPAP). Conclusion：Korean child psychiatry has achieved a remarkable progress for the past 20 years and is currently producing 15 or more child psychiatry each year. However, there are needs of more active involvements in adolescent problems, more active consultation-liaison services at general hospitals as well as community mental health institutions. More school consultation and preventive educational services are desired. There is a urgent need of carrying out more empirical studies with strong scientific rigor. Korean Academy should pay attention and provide assistance to the development of child psychiatry service in other countries in Asia.

• Asia pacific journal of information systems
• /
• v.24 no.4
• /
• pp.577-610
• /
• 2014

Although service innovation is not a new concept, innovation research in general tends to focus on technological innovation by manufacturing firms. With this view, innovation studies focus on product(e.g., goods) and process(e.g., product systems) innovation, ignoring service innovation and its inherent opportunities. Since major economy has been transformed to service economy, service innovation is considered a new effective way to sustain and gain a competitive advantage. Service innovation is no longer regarded merely as a side activity to product innovation; it has become a main research topic in its own right, accompanied by an increasing focus on services. While the number of service innovation studies has increased dramatically in the past 30 years in international research, few studies have been performed in domestic studies because domestic service innovation research began from the middle of 2000. In addition, there are no comprehensive literature reviews describing the evolution of service innovation research in both international and domestic studies because of the heterogeneities of service industry and multidiscipline characteristics of service innovation studies. To bridge this research gap, the purpose of this paper is to perform an extensive literature review and synthesis to enable a critical review of extant research on service innovation and trace its evolution, which will establish a foundation for further studies. By reviewing 169 articles (136 international papers; 33 domestic papers) published between 2000 and 2014 (in past 15 years), primarily in leading service, innovation and management information systems journals, this study analyzes the progression of service innovation research according to the four aspects such as number of studies, topics, methodologies and target industries. Overall, the view of service innovation has evolved, from a complement of traditional product innovation to a multidimensional, all-encompassing concept that entails several functions, both within and outside the firms. The results showed that domestic research still stays at the formation phase of service innovation studies although international research is in the maturity or multidimensional phase. We found increasing recent activities pertaining to service innovation, resulting from the increasing interest in services innovation across various industries and the links of new topics to the service innovation concept in both international and domestic studies. However, the main focus of service innovation research showed a different propensity between international and domestic studies: the former mainly focuses on a much more diversified pattern, emphasizing the linkages between service innovation and business strategy while the latter mainly focuses on the service innovation process(system) and service design. In addition, there are many case studies in domestic studies while many empirical studies in international studies. Domestic studies should increases the understanding of the interplay between service innovation and product innovation within manufacturing firms. Furthermore, rather than focusing on intrinsic distinctions between service innovation and product innovation, researchers should strive to develop and conceptualize service innovation in domestics studies. The present research also provides useful implications for practitioners. First, this study contributes to expand the current understanding of service innovation research by performing an extensive literature review. Second, tracing and comparing the progression and trends of service innovation research between international and domestic studies, this study showed the similarities and differences between them, which provide practical guidance on future research directions and research agenda. Third, this study performed literature review establishing the analysis system in the initial stage and using them to analyze articles, which is leading to explain the research review of service innovation more systematically and objectively. Finally, this study suggests the domestic researchers their future interests and topics of service innovation research.

• Journal of Broadcast Engineering
• /
• v.24 no.5
• /
• pp.836-848
• /
• 2019

This paper aims at providing a critical view over the cybernetics theory especially of first generation on which the artificial intelligence heavily depends nowadays. There has been a commonly accepted thought that the conception of artificial intelligence could not has been possible without being influenced by N. Wiener's cybernetic feedback based information system. Despite the founder of contemporary cybernetics' ethical concerns in order to avoid an increasing entropy phenomena(social violence, economic misery, wars) produced through a negative dynamics of the western modernity regarded as the most advanced form of humanism. In this civilizationally changing atmosphere, the newly born cybernetic technology was thus firmly believed as an antidote to these vices deeply rooted in humanism itself. But cybernetics has been turned out to be a self-organizing, self-controlling mechanical system that entails the possibility of telegraphing human brain (which are transformed into patterns) through the uploading of human brain neurons digitalized by the artificial intelligence embedded into computing technology. On this background emerges posthuman (or posthumanism) movement of which concepts have been theorized mainly by its ardent apostles like N. K. Hayles, Neil Bedington, Laurent Alexandre, Donna J. Haraway. The converging of NBIC Technologies leading to the opening of a much more digitalizing society has served as a catalyst to promote the posthuman representations and different narratives especially in the contemporary visual arts as well as in the study of humanities including philosophy and fictional literature. Once Bruno Latour wrote "Modernity is often defined in terms of humanism, either as a way of saluting the birth of 'man' or as a way of announcing his death. But this habit is itself modern, because it remains asymmetrical. It overlooks the simultaneous birth of 'nonhumaniy' - things, or objects, or beasts, - and the equally strange beginning of a crossed-out God, relegated to the sidelines."4) These highly suggestive ideas enable us to better understand what kind of human beings would emerge following the dazzlingly accelerating advancement of artificial intelligence technology. We wonder whether or not this newly born humankind would become essentially Homo Artificialis as a neuronal man stripping off his biological apparatus. However due to this unprecedented situation humans should deal with enormous challenges involving ethical, metaphysical, existential implications on their life.

• Journal of the Daesoon Academy of Sciences
• /
• v.39
• /
• pp.99-136
• /
• 2021

Grievance-resolution pursues reconciliation, mutual beneficence, and consolidation. Accordingly, the concept of grievance-resolution is a norm, a principle, as well as an ideology that aims to realize an ideal society and satisfy human desires. Such ideological thought transcended into religious doctrine and was systemized by Jeungsan, Kang Il-sun. He focused on grudges that represented the intrinsic sentiment of Korea and apprehended that grudges are the grounds and reason for the devastation of the world. Furthermore, Jeungsan was a figure who reinterpreted the concept of grievance-resolution via a religious perspective through an in-depth study which transformed into a doctrinal system. He practiced the Reordering Works of grievance-resolution on a universal dimension to religiously redeem all things. Jeungsan completely resolved all the grudges and grievances that filled up the Three Realms (Heaven, Earth, and Humanity) through the concept of grievance-resolution and emphasized that he would establish an ideal society on earth to complete the redemption of human beings. Jeungsan apprehended that the essential characteristics of grudges and grievances were the fundamental reason for the destruction of the world. In this regard, he insisted that the redemption of the world should be achieved through the grievance-resolution. Grievance-resolution is an essential aspect and principle of Jeungsan's system of thought. In addition, it is a concrete approach to establish the earthly paradise of the Later World. Jeungsan implemented a method to redeem humankind by systemizing the intrinsic sentiments common in Korea - namely, the concept of grievance-resolution- and he suggested it as a religious practice which was the principle behind the Reordering Works of Heaven and Earth. Jeungsan defined that his own era was a time of grievance-resolution. In addition, he insisted that grievances and grudges had existed from the beginning of humankind. Jeungsan also said that there were grievances and grudges in heavenly planes, human planes, and underworldly planes. It was thereby necessary to do beneficial deeds for others and reciprocate beneficence in order to resolve grievances. He emphasized that a process wherein all human desires could be satisfied was essential. Furthermore, Jeungsan stressed that this present time should focus on the process of grievance-resolution on a practical level.