• Restorative Dentistry and Endodontics
• /
• v.13 no.2
• /
• pp.207-220
• /
• 1988

The purpose of this study was to measure roughness on the polished surfaces of composite resin, and was to observe the polished surfaces under Scanning Electron Microscope. The surface roughness tester (Surfcom 700A Semitsu Profilometer Tokyo. Japan) was used to measure roughness of polished surfaces. In this study, 4 brands of composite resin were examined, Pyrofil bond anterior Bell-Feel anterior Clearfil F II and Microrest A.P. White point, Silicone point, Super snap, and Sof-Lex medium disc as cutting instrument, and celluloid matrix were used. The results obtained were as follows. 1) The celluloid matrix produced the smoothest surfaces. 2) Microrest composite resin had smoother surface than any other composite resins after polishing. 3) The values of surface roughness made by White point, Silicon point and Super snap were similar. 4) The surfaces made by Sof-Lex medium disc was smoother than the surfaces made by any other polishing instruments.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.4
• /
• pp.1-5
• /
• 2019

This study has been focused on properties of surface technology for large diameter upper electrode using in high density plasma process as like semi-conductor manufacturing process. The experimental studies have been carried out to get mirror surface for upper electrode. For a formation of high surface quality upper electrode, single crystal silicon upper electrode has been mechanical and chemical machining worked. Mechanical machining work of the upper electrode is carried out with varying mesh type using diamond wheel. In case of chemical machining work, upper electrode surface roughness was observed to be strongly dependent upon the etchant. The different surface roughness characteristics were observed according to etchant. The machining result of the surface roughness and surface morphology have been analyzed by use of surface roughness tester, laser microscope and ICP-MS.

• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.349-354
• /
• 2002

In order to find the effect of lubricant viscosity, sheet surface roughness, tool geometry, and forming speed on the frictional characteristics in sheet metal forming, a sheet metal friction tester was designed and manufactured and friction test of various sheet were performed. Friction test results showed that as the lubricant viscosity becomes lower, the friction coefficient is higher. When surface roughness is extremely low or high, the friction coefficient is relatively high. The result also show that as the punch radius and punch speed becomes bigger, the friction coefficient is smaller. Using experimental results, the mathematical expression between friction coefficient and lubricant viscosity, surface roughness, punch comer radius, or punch speed is also described.

• Journal of the Korean Ceramic Society
• /
• v.49 no.1
• /
• pp.90-94
• /
• 2012

This study has been focused on properties of mirror surface grinding technology by ELID(Electrolytic In-process Dressing) for metal matrix ceramic composites using in high precision mirror for optics. The experimental studies have been carried out to get mirror surface by grinding for composites, Al-SiC, Al-graphite and Mg-SiC. Grinding process is carried out with varying abrasive mesh type, depth of cut and feed rate using diamond wheel. The machining result of the surface roughness and condition of ground surface, have been analyzed by use of surface roughness tester and SEM measurement system. ELID grinding technology could be applied successfully for the mirror-surface manufacturing processes in spite of ductility of metal matrix material. As the results of experiments, surface roughness of Al-SiC(45 wt%) has been the most superior in these experimental work-pieces as 0.021 ${\mu}m$ Ra.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.6 no.1
• /
• pp.7-13
• /
• 1979

To evaluate the surface roughness of subgingival area of S. P. crown margins subjected to various polishing procedures, the study was performed by use of metallograph and surface roughness tester. The following results were obtained; 1) Abrasive stone wheel produced the roughest surface ($16.0{\mu}m$). 2) Final polish with rouge after polishing with rubber wheel, subsequent to abrasive stone wheel, produced the smoothest surface ($0.3{\mu}m$). 3) Both polish with rubber wheel after polshing with abrasive stone wheel, and polish with pumice (coarse$\rightarrow$medium$\rightarrow$fine) produced same surface roughness ($0.8{\mu}m$).

• Tribology and Lubricants
• /
• v.21 no.3
• /
• pp.130-135
• /
• 2005

Dry sliding wear resistance of DLC coated silicon disk with different surface roughness has been evaluated using a ball-on-disk sliding tester. It was found that the transfer layer formed on steel ball produced a low friction regime and the formation of transfer layer was more active with increasing the substrate surface roughness. Wear life of DLC coating was increased as increasing the real area of contact.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.13 no.4
• /
• pp.209-214
• /
• 1984

Friction factors and equivalent sand roughness of PVC pipe fittings have been studied by experiments in the Reynolds number range of $2,000\~70,000$. PVC pipe fittings studied are straight pipes, $90^{\circ}$ elbows and tees with 15, 25, and 40mm in norminal diameter, all manufactured in Korea with KS mark approval. Equivalent relative roughness of PVC pipes obtained lies between smooth pipe and 0.002. The study shows that equivalent sand roughness of PVC pipes increasses in proportion of the square root of pipe diameter , and can be approximately abtained by multiplying 4 to the root mean square value measured by metal surface roughness tester. Loss coefficient of PVC $90^{\circ}$ elbows decreases slowly with increasing Reynolds number. Loss coeffiicent of tees is a function of ratio of flow rates and Reynolds number.

• The Journal of Korean Academy of Prosthodontics
• /
• v.36 no.3
• /
• pp.506-513
• /
• 1998

This study was designed to compare the smoothness by glazing method with that by polishing method after 48 specimens of Ceramco II block, one of porcelain materials used for PFM, were baked according to the manufacturer's directions. The specimens were roughened with new green stone at 15,000rpm for 30 seconds and sandblasted with $25{\mu}$aluminum oxide for 15 seconds. They were divided into 4 groups at random, and 4 groups were prepared as follows : Group I : specimens were autoglazed and overpolished with polishing system. Group II : specimens were polished with only polishing system. Group III : specimens were glazed after adding glazing liquid, vitachrom 'L'-fluid (vita zahnfabrik co. Germany) to the rough surface Group V : specimens were just autoglazed Using the surface roughness tester, Ra, Rmax. and Rz were estimated 5 times per specimen, and recording process of mean value was repeated 3 times. The results were as follows : 1. The Ra of group I and group II was lower than group III and group IV (p<001). 2. There was lower value of Rz in group I and group II than group III and group IV (p<001). 3. The Rmax of group I (overpolished with polishing system after autoglazing) and group II (polished with only polishing system) was lower than group III (glazed after adding glazing liquid) and group IV (autoglazed) (p<001). 4. There was not a statistically significant difference between group I and II and between group III and IV (p>001). 5. The roughness was increase in order of group I, II, III, IV in SEM

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.1 s.113
• /
• pp.27-33
• /
• 2006

Newsprint is quantitatively the most important printing paper. The demands for its printability are continuously increasing. It is well known that the relationship between the physically tested paper properties and newspaper printability is unsatisfactory. In order to improve the printing quality of Korean newsprint, the printability coefficients such as maximum ink requirement(Ymax), print through were investigated. Kinds of newspapers and black printing ink were tested by IGT printability tester. Experiment condition of IGT printability tester was 14 steps between $0.2{\sim}2.8g/m^2$ of ink requirement, printing pressure was 200 N and printing velocity was 1 m/sec. The properties of newspaper samples (basis weight, bulk density, roughness, smoothness, porosity, i. e.) were examined in accordance with KS and TAPPI standard testing methods. The result of this study are respected for usefulness printing quality management of Korean newsprint.

• Journal of Technologic Dentistry
• /
• v.37 no.4
• /
• pp.205-212
• /
• 2015

Purpose: The objective of this study was to compare the surface roughness according to polishing process in conventional laboratory techniques used for polishing three different acrylic denture base resins. Materials and methods: Specimen preparation and surface polishing procedures were conducted to manufacturer's recommendation with three heat-polymerized denture base resins. Surface roughness and gloss were measured by a contact type tester and a LED gloss checker using thickness 2 mm and diameter 10 mm. There were five specimens for each acrylic resin material and polishing procedures. Mean average surface roughness (Ra) values of each specimen group were analyzed using a one-way ANOVA analysis of variance and Scheffe's post hoc test. Surfaces after surface roughness and gloss testing according to each polishing process were evaluated under a stereoscopic microscope. Results: The highest mean average surface roughness was measured($Ra=2.43{\pm}0.47$) for surfaces finished with a denture tungsten carbide bur in Triplex. The lowest surface roughness values ($Ra=0.11{\pm}0.07$) were determined in Vertex polished with a lathe. In addition, all materials revealed that surface roughness determined highly in HP1 and HP2 than other procedures. All correlation between surface roughness and gloss showed highly with three heat-polymerized resins. Specially, topmost correlation revealed than other material in Triplex. Significant differences in mean average surface roughness were found between polishing process used high speed lathe and low speed hand-piece. Conclusion: Laboratory polishing used to high speed was found to produce the smoothest surface of heat-polymerized denture base acrylic resin. Therefore, we recommended that high polishing process need to get smooth surface.