• The Journal of Advanced Prosthodontics
• /
• 제9권4호
• /
• pp.278-286
• /
• 2017

PURPOSE. The aim of this study was to determine the influence of long base lengths of a fixed partial denture (FPD) to rotational resistance with variation of vertical wall angulation. MATERIALS AND METHODS. Trigonometric calculations were done to determine the maximum wall angle needed to resist rotational displacement of an experimental-FPD model in 2-dimensional plane. The maximum wall angle calculation determines the greatest taper that resists rotation. Two different axes of rotation were used to test this model with five vertical abutment heights of 3-, 3.5-, 4-, 4.5-, and 5-mm. The two rotational axes were located on the mesial-side of the anterior abutment and the distal-side of the posterior abutment. Rotation of the FPD around the anterior axis was counter-clockwise, Posterior-Anterior (P-A) and clockwise, Anterior-Posterior (A-P) around the distal axis in the sagittal plane. RESULTS. Low levels of vertical wall taper, ${\leq}10-degrees$, were needed to resist rotational displacement in all wall height categories; 2-to-6-degrees is generally considered ideal, with 7-to-10-degrees as favorable to the long axis of the abutment. Rotation around both axes demonstrated that two axial walls of the FPD resisted rotational displacement in each direction. In addition, uneven abutment height combinations required the lowest wall angulations to achieve resistance in this study. CONCLUSION. The vertical height and angulation of FPD abutments, two rotational axes, and the long base lengths all play a role in FPD resistance form.

• Journal of Electrical Engineering and information Science
• /
• 제3권1호
• /
• pp.86-93
• /
• 1998

In this paper, we propose an effective on-line identification method for rotor resistance, which is useful in making speed control of induction motors without rotational transducers robust with respect to the variation in rotor resistance. Our identification method for rotor resistance is based on the linearly perturbed equations of the closed-loop system for sensorless speed control about th operating point. Our identification method for rotor resistance uses only the information of stator currents and voltages. In can provide fairly good identification accuracy regardless of load conditions. Some experimental results are presented to demonstrate the practical use of our identification method. For our experimental work, we have built a sensorless control system, in which all algorithms are implemented on a DSP. Our experimental results confirm that our on-line identification method allows for high precision speed control of commercially available induction motors without rotational transducers.

• Earthquakes and Structures
• /
• 제10권4호
• /
• pp.867-891
• /
• 2016

This paper addresses numerically the behavior of steel structures under Fire-after-Earthquake (FAE) loading. The study is focused on a four-storey library building and takes into account the damage that is induced in structural members due to earthquake. The basic objective is the assessment of both the fire-behavior and the fire-resistance of the structure in the case where the structure is damaged due to earthquake. The combined FAE scenarios involve two different stages: during the first stage, the structure is subjected to the ground motion record, while in the second stage the fire occurs. Different time-acceleration records are examined, each scaled to multiple levels of the Peak Ground Acceleration (PGA) in order to represent more severe earthquakes with lower probability of occurrence. In order to study in a systematic manner the behavior of the structure for the various FAE scenarios, a two-dimensional beam finite element model is developed, using the non-linear finite element analysis code MSC-MARC. The fire resistance of the structure is determined using rotational limits based on the ductility of structural members that are subjected to fire. These limits are temperature dependent and take into account the level of the structural damage at the end of the earthquake and the effect of geometric initial imperfections of structural members.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권1호
• /
• pp.87-97
• /
• 2014

In this study, the model tests were conducted on the short piles installed in sands under a horizontal pullout load to investigate their behavior characteristics. From the horizontal loading tests where dimensions of the pile diameter and length, and loading point were varied, the horizontal pullout resistance and the rotational and translational movement pattern of the pile were investigated. As a result, the horizontal pullout resistance of the pile embedded in sands was dependent on the pile length, diameter, loading point, etc. The ultimate horizontal pullout load tended to increase as the loading point (h/L) moved to the bottom from the top of the pile, regardless of the ratio between the pile length and diameter (L/D), reached the maximum value at the point of h/L = 0.75, and decreased afterwards. When the horizontal pullout load acted on the upper part above the middle of the pile, the pile rotated clockwise and moved to the pullout direction, and the pivot point of the pile was located at 150-360mm depth below the ground surface. On the other hand, when the horizontal pullout load acted on the lower part of the pile, the pile rotated counterclockwise and travelled horizontally, and the rotational angle was very small.

• 대한수학회지
• /
• 제44권3호
• /
• pp.707-717
• /
• 2007

Arches are constrained with rotational resistance at both edges. An energy method is used to derive variational formulation which is used to prove the existence of equilibrium states of elastic circular arches for the torsional spring constants ${\rho}-\;{\geq}\;0,\;{\rho}+\;{\geq}\;0,\;and\;{\rho}-\;+\;{\rho}+\;>\;0$. The boundary conditions are searched using the existence of minimum potential energy.

• 한국기계가공학회지
• /
• 제21권8호
• /
• pp.99-109
• /
• 2022

In this study, an electric resistance-heated surface friction spot-welding process was proposed and tested for the spot-welding ability of copper and aluminum dissimilar metal sheets using electric resistance heating and surface friction heating. This process has welding variables, such as the current value, energizing cycles, rotational speed, and friction time. The current value and energizing cycle can affect the resistance heat, and the rotational speed of the rotating pin and friction time influence frictional heat generation. Resistance heating before friction heating has a preheating effect on the Cu-Al contact interface and a positive effect on preventing friction heat loss during the friction stage. However, because resistance preheating can soften the copper sheet and affect the contact stress and friction coefficient, it has difficulties that may adversely affect frictional heat generation. Therefore, the optimal combination of welding variables should be determined through simulations and experiments of the spot-welding process to determine the effects of electric resistance preheating on the suggested process. Through this procedure, it is known that the proposed spot-welding process can improve the welding quality during the spot welding of Cu-Al sheets.

• 한국전산구조공학회논문집
• /
• 제26권6호
• /
• pp.463-470
• /
• 2013

본 연구에서는 풍진동에 대한 현수교의 거동을 예측하기 위하여 바닥판의 비틀림강성을 고려하여 Mckenna and Tuama 모델(2001)을 개선한 2D 간단해석 방법을 제안하였다. 기존의 모델은 풍속이 증가할수록, 진동수가 낮아질수록 비정상적인 값을 나타내고, 비틀림모드의 공진현상을 묘사할 수 없었다. 이에 본 연구에서는 비틀림강성을 고려하여 풍속에 따른, 진동수에 따른 비틀림진동을 분석하였다. 해석결과 진동 초기의 수직모드는 점차 비틀림모드로 전이되며 수직모드는 안정적으로 진동하는 것을 확인하였다. 또한 비틀림강성 효과를 고려하여 해석을 수행한 결과 수직모드는 시간이 경과함에 따라 안정화되는 모습을 보이나 비틀림 진폭은 일정시간(약 200초) 이후 나타나기 시작하여 비틀림각을 지속적으로 유지하였으며 맥놀이 주기는 풍속이 증가하면서 점차 감소하였다. 비틀림 강성에 따라 서로 다른 풍하중의 풍속과 진동수에 비틀림모드의 공진현상을 나타내므로 실제 설계에는 반드시 이러한 영향이 고려되어야 할 것이다.

• Tribology and Lubricants
• /
• 제12권4호
• /
• pp.28-34
• /
• 1996

The lubrication characteristics of high-speed ball bearings have been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flow rates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 2969 N axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• Steel and Composite Structures
• /
• 제18권2호
• /
• pp.325-344
• /
• 2015

Experimental tests on cellular beams with sinusoidal openings showed two main failure modes around the openings. They concern the formation of four plastic hinges and the local instability of the sinusoidal part of the opening. In parallel, numerical analysis of the sinusoidal part of the opening revealed the existence of an elastic rotational restraint between the intermediate web-post and the adjacent opening panel. The aim of the present study is to present an approach to quantify this rotational restraint. Through the response surface method, a mathematical model is proposed. It shows a great ability to predict the rotational restraint value as a function of the geometrical parameters of the opening. This model can be used to perform an extensive study with various geometrical configurations of beams with the aim to develop a reliable and realistic analytical model predicting the resistance of the sinusoidal openings.

• Steel and Composite Structures
• /
• 제1권2호
• /
• pp.187-200
• /
• 2001

Most of the portal frames are designed these days by the application of plastic analysis, with the normal assumption being made that the column bases are pinned. However, the couple produced by the compression action of the inner column flange and the tension in the holding down bolts will inevitably generate some moment resistance and rotational stiffness. Full-scale portal frame tests conducted during a previous research program had suggested that this moment can be as much as 20% of the moment of resistance of the column. The size of this moment of resistance is particularly important for the design of the tensile capacity of the holding down bolts and also the bearing resistance of the foundation. The present research program is aiming at defining this moment of resistance in simple design terms so that it could be included in the design of the frame. The investigation also included the study of the semi-rigid behaviour of the column base/foundation, which, to a certain extent, affects the overall loading capacity and stiffness of the portal frames. A series of column bases with various details were tested and were used to calibrate a finite element model which is able to simulate the action of the holding down bolts, the effect of the concrete foundation and the deformation of the base plate.