• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.365-368
• /
• 1995

Rotary Compressor has many AE(Acoustic Emission) sources according to condition of parts because it is operated with combination of various parts. In this study, analysis of AE raw signal generated form Rotary compressor which artificially-made parts inflicted abnormal condition was carried out. AE raw signals were acquired form high-speed A/D board, and many burst type signals were observed. By analyzing burst type signals which is caused form internal AE source,efficient AE parameters for monitoring and diagnosis were presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.601-604
• /
• 2002

In this paper bolt-tightened Langevin type vibrator was designed using longitudinal-torsional vibration. These two vibrations make rotary displacement at the end of the vibrator. ANSYS was used to determine shape and dimension of the vibrator in addition to resonant frequency, displacement and stress distribution. This kind of vibrator can be applied for a brakeless and gearless rotary motor which has high torque at low speed.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.2815-2817
• /
• 2005

This paper presents an experiment study on the control of a rotary-type inverted pendulum based on the Takagi-Sugeno (T-S) fuzzy model approach. A sufficient condition for stability of the T-S fuzzy control system is given via linear matrix inequalities (LMIs). State-feedback controllers for sub-systems are designed from the sufficient condition via change of variables which is one of the popular LMI techniques. Experimental results on a rotary-type inverted pendulum control show the feasibility of the T-S fuzzy model-based control method.

• 한국HCI학회:학술대회논문집
• /
• 2007.02a
• /
• pp.739-743
• /
• 2007

In this paper, a stereoscopic display system using a rotary disk type beam shutter and two beam projectors is proposed. It is a kind of active stereoscopic display and can be easily converted from passive stereoscopic system using polarizing filters. If it is possible to synchronize the revolution speed of the beam shutter with the integer multiple of the scanning frequency of the beam projectors, we can obtain a comparable performance with our system to an active stereoscopic system using one expensive high performance beam projector. Further, if we rotate the beam shutter at sufficiently high revolution speed, our active stereoscopic system works regardless of synchronization and thus the system is much easier to implement.

• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.54-61
• /
• 2006

In order to prevent the environmental pollution, the dryers are commonly used to treat sludge that one of sewages is polluting the quality of water. Generally, the drying method is various as to the property of material and use. Rotary dryer is a good apparatus to treat them. The rotary dryer is the way that is to make substance transmission and heating using hot air between sludge particles and heated gas. In this paper, we performed a numerical analysis of the inner air flow of the ANDRICH type dryer through the changing rotational speed from 3rpm to 10rpm. A PIV can be applied to research a inner flow of ANDRICH type dryer.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.13 no.2
• /
• pp.83-88
• /
• 2005

This study investigates the air leakage and heat transfer characteristics of a commercially available rotary-type air-to-air heat exchanger with a fiber polyester matrix. Crossover leakage between the exhaust and supply air is measured using a tracer gas method for various ventilation rates and rotational speeds of the wheel. A correlation equation for the leakage is obtained by summing up pressure leakage and carryover leakage. The pressure leakage is observed to be a function of ventilation rate only, and the carryover leakage is found to be a linear function of wheel speed. The real efficiency of the heat exchanger can be obtained from its apparent efficiency by taking into account the leakage ratio. The heat recovery efficiency decreases, as the ventilation rate increases. As the wheel speed increases, however, the efficiency increases initially but reaches a constant value for the speeds over 10rpm.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.405-407
• /
• 2000

The most generally implemented method to detect the ground speed of the railway vehicles is to use the rotary type speed sensor attached to wheel axle. The Slip or sliding phenomenon on the railway vehicles occurs frequently caused by the weak viscosity of the wheel. Thus, precisely to control the car, the slip/sliding detection system is required. In this paper we proposed for the speed data management system, which uses rotary type speed sensor. Proposed speed management system can detect the slip/sliding with wheel axle as well as correct the generated speed error during in error time, to provide accurate speed and precise location data. The effectiveness for adapting to the railway system is clarified by the computer simulation.

• Journal of the Korean Society of Combustion
• /
• v.9 no.3
• /
• pp.1-9
• /
• 2004

This study is aimed to characterize the combustion behavior of solid fuel in the various types of the combustors: stoker, rotary kiln and fluidized bed type combustors. Three different types of reduced-scale combustors are introduced, and temperatures and flue gas compositions are measured for various fuel sizes, water contents, initial temperature, and air flow rates. In case of the rotary kiln combustor, effects of rotating speed of the combustor are also investigated. Mean carbon conversion time (MCCT) and flame propagation rate (FPR) are used for the quantitative analysis. It is revealed that the reaction rates of the fuel are significantly influenced by the fuel characteristics, type of the combustors and air flow rate. Major design parameters for each type of the combustors are summarized through the reduced-scaled model analysis.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.12
• /
• pp.1197-1203
• /
• 2004

This study investigates the air leakage and heat transfer characteristics of a rotary-type air-to-air heat exchanger with a fiber polyester matrix. The leakage airflow rate is measured using a tracer gas method for various ventilation rates and rotational speeds of the matrix wheel. A correlation equation for air leakage is obtained by combining the pressure leakage and the carryover leakage. The pressure leakage is observed to be a function of ventilation airflow rate only, and the carryover leakage is found to be a linear function of rotational speed. The real efficiency of the heat exchanger can be obtained from its apparent efficiencies by taking into account the air leakage ratio. As the ventilation rate increases, the heat recovery efficiency decreases. As the rotational speed of the matrix increases, the efficiency increases initially but reaches a constant value for the rotational speeds over 10 rpm.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.106-113
• /
• 1995

Surface mounters are used to mount the parts of electronic products on PCB(Printed Circuit Board. Those machines rely on high precision, high productivity, and software for accomodation of use. In this paper, two algorithms and a software which can give the users the acco-modation and high productivity for rotary type surface mounters are presented. The algo- rithms for development of of the software consider all factors which affect the effeciency of the operation. And the interface between user and machine for the accomodation of use can be achieved through the developed software.