• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.11a
• /
• pp.45-49
• /
• 2001

To maintain the freshness of produce, because of stand away between produced and consumer, we need refrigeration system that can supply to consumer at cold chain as soon as gathering. General refrigeration system consist of refrigeration chamber or low temperature store. But the vacuum technology can rapidly refrigeration without refrigerator. This precool system possible to get low precooled temperature, suitable for the fishes, the meat, the vegetables, the fruit etc. Especially get advantage that quality maintain through rapid refrigeration of ferment directly generate heat. Vacuum precool system's principle is that water saturated temperature reduce according to pressure is get to vacuum area, so product temperature reduce as water evaporation at product. In vacuum suction, unit, on early experiment period run the rotary type vacuum pump at purpose pressure, then maintain pressure by water-diven ejector. As the results, cabbage took about 60 minutes to reach from $23.2^{\circ}C$ to $4.5^{\circ}C$at 5mgHg abs.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.12 s.255
• /
• pp.1534-1542
• /
• 2006

In this paper, the concept of accelerated life test, which is a popular research field nowadays, is applied to the shot peened material. To predict the efficient and exact room temperature fatigue characteristics from the high temperature fatigue data, the adequate accelerated model is investigated. Ono type rotary bending fatigue tester and high temperature chamber were used for the experiment. Room temperature fatigue lives were predicted by applying accelerated models and doing reliability evaluation. Room temperature fatigue tests were accomplished to check the effectiveness of predicted data and the adequate accelerated life test models were presented by considering errors. Experimental result using Arrhenius model, fatigue limit obtain almost 5.45% of error, inverse power law has about 1.36% of error, so we found that inverse power law is applied well to temperature-life relative of shot peened material.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.39-39
• /
• 2010

인공위성이 임무를 수행하는 우주환경은 지상 환경과 달리 고진공 및 극저온의 극한환경으로 지상에서는 제대로 작동하는 것으로 관찰되더라도 우주환경에서는 예상하지 못한 기능장애를 일으켜 위성의 성능에 치명적인 영향을 미치기도 한다. 이에 10-5 torr 이하의 고진공과 $-180^{\circ}C$ 이하의 극저온 환경을 지상에서 모사하여 위성체의 안정성 및 신뢰성을 시험한다. 한국항공우주연구원에서 보유한 각종 우주환경모사용 챔버들은 설치 후 10년 이상 가동한 노후 장비들로 적정 성능을 지속적으로 유지하기 위하여 기본이 되는 진공 펌프들의 교체 작업을 수행하였다. 특히, 기존 사용하던 저진공펌프 중 oil type의 rotary vane 펌프를 dry 펌프로 교체하였으며, 배기 전 준비과정에 많은 시간이 소요되는 cryo 펌프를 turbo-molecular 펌프로 교체하였다. 본 논문에서는 펌프 교체 전 적정 사양 선정을 위한 준비과정 및 펌프의 교체 및 그 결과에 대해 기술한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.245-246
• /
• 2006

For developing 5-axis laser cutting systems, many problems such as rotating of laser head or table, 5-axis tool path generation and collision avoidance between laser head and product should be solved. In this paper, a five-axis laser cutting machine with table swivel and rotary type configuration is developed. The five axes (X,Y,Z,A,B) are controlled and interfaced to PC via MMC board. Two kinds of CAM S/W such as commercial 5-axis CAM S/W(Euclid) and UG-API are engaged to generate NC code for the developed 5-axis laser cutting machine.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.8
• /
• pp.38-45
• /
• 1999

The 2-trowel type concrete floor finishing robot can move in any direction by adjusting the posture or trowels without any wheels. Since the quality of the smoothed and polished concrete floor is determined by plastering speed, we need to control the velocity of the robot. However, we cannot use the typical motion control method because it is very difficult to measure the velocity of the robot, in contrast to the mobile robots with wheels. To overcome this difficulty, the following are studied in this paper: we found that the robot dynamics has the disturbance depending on its translational speed, and showed that there exists the saturated velocity of the robot which is set by the posture of the trowels, and obtained the relationship between the saturated velocity and the posture in the translation. The result enables us to control the motion of the robot only by adjusting the posture of trowels without measuring the velocity of the robot. Currently, we built the troweling robot and are experimenting its performance with the proposed motion control method.

• Journal of the Korean Society of Tobacco Science
• /
• v.15 no.1
• /
• pp.49-56
• /
• 1993

Nitric oxide of gas phase in cigarette smoke was conveniently determined by Chemiluminescence NO analyzer with 20 ports rotary type smoking machine Data are presented to support this observation. On the basis of this method the amount of NO in the smoke from nonblended and commercial cigarettes were estimated. Gas phase NO concentration in main stream smoke was correlated well with the nitrate levels in tobacco leaves, but there was no correlation with the tar yields. In consequence, it would be considered that the methodology in this study provided simple and rapid quantification for NO in cigarette smoke.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.1
• /
• pp.1-7
• /
• 2009

Recently, the growing market demand for small and slim mobile phone cameras requires the size reduction of the camera module. In this paper, an auto-focusing actuator for camera phones is proposed by converting the rotational motion by a rotary VCM actuator into the linear motion using a novel cam structure. This new concept for auto-focusing module enables the reduction of the module thickness and low power consumption. This paper presents the theoretical analysis and optimal design for VCM actuator, cam structure and preload spring. Finally, the experimental results using a prototype with the size of $9.9{\times}9.9{\times}5.9\;mm^3$ are compared with the theoretical predictions.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.179-180
• /
• 2018

This study aims to provide a more comfortable environment for the external environment by designing a rotable dwelling that deviates from the conventional fixed residential concept. The round pillars, which are the center of the building, are constructed by placing the CFT (concrete Filled steel Tube) technique in place and assembling modular houses with columns. This study combines existing building techniques. Korea also needs to develop various related studies quickly.

• Journal of Magnetics
• /
• v.18 no.4
• /
• pp.473-480
• /
• 2013

A new concept design of electromagnetic energy harvester is proposed for powering a tire pressure monitoring sensor (TPMS). The thin coil strap is attached on the circumferential surface of a rim and a permanent magnet is placed on the brake caliper system. When the wheel rotates, the relative motion between the magnet and the coil generates electrical energy by electromagnetic induction. The generated energy is stored in a storage unit (rechargeable battery, capacitor) and used for TPMS operation and wireless signal transmission. Innovative layered design of the strap is provided for maximizing energy generation. Finite Element Method (FEM) and experiment results on the proposed design are compared to validate the proposed design; further, the method for design improvement is discussed. The proposed design is excellent in terms of durability and sustainability because it utilizes the everlasting rotary motion throughout the vehicle life and does not require material deformation.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.4E
• /
• pp.20-25
• /
• 1999

To get accurate natural frequencies of an engine crankshafts, finite element equations of motion are developed, taking real geometries of the shaft into account. For the crankshaft with wide crank webs, a specialized rotating web element is developed. This includes the effects of rotary inertia, gyroscopic moment, and shear. After the finite element equations are constructed, eigenvalues are extracted from the system equations to get natural frequencies, based on the Sturm sequence method which exploits the banded forms of the system matrices to reduce computations. The scheme developed can be used for the free vibration analysis of any type of spinning structures which include skew symmetric gyroscopic moment matrix in the system matrices. The results are compared with experimental data in order to confirm the study.