• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3341-3346
• /
• 2007

This paper presents effects of carburetor throttle angle on the performance characteristics of a small sparkignited, gasoline engine. The engine used in the test is a single cylinder, two-stroke, air-cooled 26cc SI engine for brush-cutter. We measured the rpm, torque, power, and fuel consumption according to the six different throttle angle conditions of the rotary-type carburetor and to the engine dynamometer loads. We had concluded that maximum power happened at 5000${\sim}$6000rpm and at the same condition was the minimum specific fuel consumption.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.19 no.2
• /
• pp.27-31
• /
• 1982

The practical utilization of the frequency and normal mode equations of uniform Timoshenko beams such as those presented by Huang is not simple due to their highly trancendental nature. In this note largely simplified equations obtained for the fixed-fixed and the free-free boundary conditions, the modes of which are separable into symmetric modes and antisymmetric ones, are given. Numerical results obtains for six common-type boundary conditions show that the quantitative measure of the effect of rotary inertia and shear deformation on the natural frequency is greatly dependent upon the boundary conditions as well as the order number.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.289-291
• /
• 1996

Linear induction motor(LIM) is widely used to drive magnetic levitation train. To drive LIM, different control method compared with conventional rotary type machine is needed. Since vertical force is generated inherently and it effects on the levitation system, vertical force should be kept constant for stable levitation. To keep vertical force constant, slip frequency should be kept constant. Once slip frequency is kept constant, tractive force can be controlled by adjusting motor currents. In this paper, control methods used so far arc analyzed with some experimental results and decoupling control algorithm is proposed to control tractive and vertical force separately. Control algorithm is verified through simulation.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.77-82
• /
• 2001

The 3-lobes blower has been conventionally made by constructing the impeller with the cross-section of simple arc, and has several problems such as noise, vibration and the oscillation of torque. These are caused by the variation of clearance between both impellers rotating in geared. In the present study, an approach for the design of cross-section of impeller has been proposed to prevent the above problems. The whole cross-section is divided into the concave and convex part. The concave zone is designed by simple arc and the convex zone is modified by the condition that some part of convex zone is always in contact with the other impeller during rotating. A sample design has been carried out and it can be seen that the clearance between both impellers is always uniform and the validity of present work has been verified.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.316-321
• /
• 2001

The optical storage device has recently experienced significant improvement, especially for the aspects of high capacity and fast transfer rate. However, it is necessary to study a new shape of air bearing surface for the rotary type actuator because the optical storage device has the lower access time than that of HDD (Hard Disk Drives). In this study, we proposed the air bearing shape by using SA (Simulated Annealing) algorithm which is very effective to achieve the global optimum instead of many local optimums. The objective of optimization is to minimize the deviation in flying height from a target value 100nm. In addition, the pitch and roll angle should be maintained within the operation limits.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.10
• /
• pp.1477-1482
• /
• 2012

This paper deals with a new variable microwave power distributor and a connector between a deck plate and a input power waveguide for indoor microwave wireless power transmission. We design a new type connector built in the 3-stage coaxial line structure, and calculate the return loss of the connector at 2.45GHz. Newly designed connector shows the excellent return loss performance less than -30dB at the operating frequency of 2.45GHz. And we show a power distributor in which the dividing ratio of the power is controlled mechanically by three rotary fins. The distributor can control the dividing power from 4.5% to 58% with the variance of 5% output power. The experimentally tested results of the distributor are good agreement with the simulation within the return loss of 1%.

• Journal of KSNVE
• /
• v.8 no.2
• /
• pp.336-345
• /
• 1998

The dynamic instability of cylindrical shell with clamped-free boundary condition subjected to constant follower force or $P_0 + P_1cos {\Omega}_t$ type pulsating follower force is analyzed. The motion of shell is modeled using the shell theory considering rotary inertia and shear deformation, and analyzed with finite element method. In case of constant follower force, the changes of eigenvalues dependent on the magnitude of applied load are investigated and the critical loads are obtained. In case pulsating follower force, instability regions of exicitation frequency are obtained by modal transform with right and left modal matrix and by multiple scales method. The effects of thickness ratio and aspect ratio on the instability of shell are studied.

• Journal of Biosystems Engineering
• /
• v.24 no.3
• /
• pp.253-258
• /
• 1999

This study was conducted to develop an automatic egg inspection system for detecting creaked eggs based on acoustic impulse response. This system includes a sound generator, a sound sensor with signal conditioner, and a computer. The sound generator that hit the sharp of the dull edges of an egg was constructed with a ceramic ball pendulum attached to a rotary type solenoid. The signal conditioner included a pre-amplifier and a digital signal processing (DSP) board. The parameters for distinguishing cracked and normal eggs were the area, the geometric centroid and the resonance frequency of power spectrum of the acoustic signal generated. An algorithm for on-line detection of the continuous transferring eggs was developed. The performance tests resulted with 91% success rate to separate cracked and normal eggs at the rate of 1 second per an egg.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.877-885
• /
• 1993

Three types of solar grain dryers, namely , the solar grain bin dryer, the solar greenhouse rotary drum dryer and small scale solar green house tray dryer, have been tested. The results showed that each type of solar grain dryer has its feature. These solar drying units have three main advantages : (1) Required commercial energy to remove 1Kg moist from rough rice is only 5.3% to 15.8% of the energy consumed by common heated dryer : 2) The area of solar drying system is only about 10% of the area of the sunny ground to give equal drying capacity ; (3) There are good drying quality in the moisture uniform , germination percentage, and grain color.

• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.360-362
• /
• 2006

This paper proposes a new track-following control method using disturbance observer with the freedom of gain and frequency adaptation in optical disk drive system. Recent ODDs use smaller track pits, higher rotation speed and broader rotational speed variations to increase the data capacity and data transfer rate. This cause the degradation of track-following performance by increasing the disturbance of the rotary system. In this paper, we discussed on a DOB structure that efficiently attenuate the disturbance without effecting the overall feedback loop characteristics on CLV type ODD which uses a higher and broader range of rotational speed. DOB structure uses two band pass filter. We analyzed the track-following performance sensitivity on rotational frequency variance and gain changes. This analysis is done on a computer simulation environment and actual ODD product.