• Journal of the Korean Chemical Society
• /
• v.7 no.2
• /
• pp.133-139
• /
• 1963

It is well-known that high temperature hurts the sizing effect of rosin size in paper making, mainly owing to the particle size of rosin-aluminium complex in paper stock. In this experiments, author find, when the temperature of stock rises up. the particle size of rosin-aluminium complex of neutral rosin size increases and the degree of sizing decreases finally. However, the behavior of Bewoid size is quite opposite to former. This result showed that, Bewoid size is suitable in hot summer and neutral rosin size in cold winter for better sizing effect.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.387-390
• /
• 2006

Cationic rosin sizes are prepared by premixing extremely pure ployaluminum chloride (PAC) and dispersed rosin size (DRS). It turned out that zeta potential and particle size of the sizing agents took a big change by Plus90 analyzer's and FTIR analyzer's analysis. It turned out that -C=O and -COOH of the DRS have both chemical reaction with PAC to form the muti-hydroxyl aluminum rosin acid and that the cationic rosin sizes modified by PAC has dissymmetric and symmetric flexible vibration two absorbing peaks of the groups (its absorbing peaks $at1596cm^{-1}\;and\;1425cm^{-1}$). By DRS reacting with PAC, zeta potential of the resin size varied from negative to cationic. $Al_{2}O_{3}/rosin=1:0.3$, zeta potential of premixed admixture is tiptop28.8mv, When joined continuously PAC, zeta potential of cationic rosin sizes descend on the contrary.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.9 no.6
• /
• pp.476-481
• /
• 2004

The aim of this study was to formulate a sustained release system for indomethacin (IND) with rosin gum obtained from a pine tree. Rosin microparticles were prepared by a disper­sion and dialysis method without the addition of surfactant. In order to investigate the influence of solvents on the formation of colloidal microparitcles, various solvents like ethanol, DMF, DMAc, and acetone were used. The rosin microparticles containing IND were characterized by X­ray differactometry (XRD) and differential scanning calorimetry (DSC). The morphologies of rosin microparticles observed by scanning electron microscopy (SEM) were spherical. The solvents used to dissolve rosin significantly affected the drug content and drug release rate of IND. The release behaviors of IND from the rosin microparticles were dependent on the drug content and size of the particles. Rosin micorparticles with a higher drug content and of a larger particle size had a slower drug release rate. Also, the IND release rate from the rosin microparticles could be regulated by the rosin content in the microparticles. From these results, rosin microparticles have the potential of being used as a sustained release system of IND.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.3
• /
• pp.74-83
• /
• 1998

The phenomenon of decrease in sizing efficiency when the stock temperature is increased is well recognized as summer sizing, and this is believed to be caused by uneven distribution of sizing agents on paper surface most often incurred by coagulation of sizing agents. When unevenly sized paper is used as coating base stock, nonuniform consolidation of the coating layer may result, which, in turn, causes uneven distribution of binder on coating surface. This causes nonuniform ink absorption to produce print mottle. In this study the effects of simple or polymeric electrolytes, storage temperature and time on the coagulation of cationic dispersed rosin size were investigated using a turbidity measurement method which was verified to correlate well with the particle size of rosin emulsion or its coagulates. Handsheets sized with rosin dispersions coagulated under various conditions were prepared and their sizing degree and coated paper properties including gloss and ink density were examined. The relationship between the sizing nonuniformity of coated papers and its ink absorption property was evaluated. Turbidity of rosin emulsion increased as the storage temperature and time were increased. Addition of simple or polymeric electrolytes caused reduction in $zeta$ -potential of the rosin dispersion and accelerated the coagulation tendency substantially. Reversion of the $zeta$ -potential of rosin dispersion, however, did not occur when coagulation was induced with simple electrolytes. On the other hand, addition of an anionic polyelectrolyte reversed the $zeta$ -potential of the flocculated rosin dispersion. This indicated that electrical double layer compaction and bridging flocculation were coagulation mechanisms for simple and polymeric electrolytes, respectively. Sizing degree decreased as coagulation of rosin was increased. Paper gloss, ink gloss and ink density were increased when sizing degree of base stock was increased most probably due to prevention of base paper swelling and increased binder migration to coating surface. This suggested that uneven printing ink density occurred when uneven sizing development was induced by coagulation of rosin particles.

• Journal of the Korean Ceramic Society
• /
• v.23 no.4
• /
• pp.35-40
• /
• 1986

The production process of a fine size fraction of Korean kaolin by ball milling is studied in this paper by analyzing the size distribution the size distribution of products with the Rosin-rammle formular and the rate process of cumulative size fractions with Alyavdin-Chujyo's formular. The size distribution is found to be divided in three regions a coarser part influenced by feed size an intermediate part where the size distribution shows a clear straight line relationship on Rosin-Rammler chart and the finest part with the ultimate limit of fineness by ball milling. Alyavdin-Chujyo's relationship is found to be valid over a very wide range of milling conditions. For different feed sizes the Alyavdin-Chujyo's relationship gives a group of straight lines with a common intersection point which can be defined as the limiting point of the persistent component region.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.1
• /
• pp.79-87
• /
• 1999

To use the agricultural residues as the raw material of molded packaging material, the packaging trays were manufactured from rice-straw pulp. The physical properties were measured to compare non-treated trays with the addition trays, such as the addition of starch, rosin size, carboxymethyl cellulose(CMC), polyethylene glycol(PEG), alkylketene dimer(AKD), polyacryl amide(PAM). The results were as follows : 1. In the addition of starch, air permeability at addition of 5% was highest. Bursting strength and tensile strength were smaller than non-treated trays. 2. In the addition of rosin size, air permeability, bursting strength and tensile strength were smaller than non-treated trays. 3. In the addition of CMC, air permeability was higher than non-treated trays. Bursting strength and tensile strength were similar to non-treated trays. 4. In the addition of PEG, air permeability was higher than non-treated trays. Bursting strength at addition of 3% was the highest and tensile strength was smaller than non-treated trays. 5. In the addition of AKD, air permeability at addition of 1% and 5% was higher than non-treated trays. Bursting strength and tensile strength were smaller than non-treated trays. 6. In the addition of PAM, air permeability at addition of 0.01% was the highest. Tensile strength at addition of 0.01% were higher than non-treated trays. 7. The water absorption of the trays decreased with increasing adding of natural additives.

• Journal of the Korean Ceramic Society
• /
• v.24 no.1
• /
• pp.1-8
• /
• 1987

The validity of Alyavdin-Chujyo's Equation was re-examined over the broader milling conditions that those previously examined. Ordinary ball mill grinding with a laboratory scale batch mill (133mmø×144mm length) were selected as the grinding methods. The results show that in ball milling the Alyavdin-Chunjyo's Equation can be applicable over wide grinding time and size range with few exceptions. The validity of which are examined and discussed. The theoretical consideration of the relation between Alyavdin-Chujyo's Equation and size distributiion equation, such as Rosin-Rammler's law, was tried, and it is found that, under the condition of alyardin-Chujyo's relation, the Rosin-Rammler size distribution law can hold.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.04b
• /
• pp.390-393
• /
• 1999

In this paper, a series of PAC (polyaluminum chloride) samples were prepared for rosin neutral sizing system. Some characters of PAC were discussed in detail. The experimental results show that it is possible to achieve neutral sizing when PAC is compounded with DRS (dispersed rosin size) instead of alum (aluminum sulfate).

• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1027-1036
• /
• 1997

The reology and several physical properties of cements are studied by varying the different mineral composition and particle size distribution(PSD) of cements with closed circuit ball mill for high workability, low heat of hydration, and high strength. In this study, we found that the workability of concretes is related to the viscosity of cement, and affects to strength. Here, this workability is affected by mineral composition (C3A) and the PSD. Especially, rosin-rammer index and 44${\mu}{\textrm}{m}$ residue in the PSD of cements are affected to water demand, casting property, slump loss, strength of cements. From the above results, the conditions of cement for high workability, low heat of hydration and high strength are to use low C3A clinker, 5-10% slag addition, and to grind cement below 0.7 rosin-rammer index, above 3.5-4.5% 44 ${\mu}{\textrm}{m}$ residue, 4000$\pm$100 $\textrm{cm}^2$/g blaine. Such cements are, therefore, supurior to super low heat cement and slag-blended cement in comparing the physical properties of strength, slump, slump-flow, adiabetic temperature, etc.

• Journal of the Korean Ceramic Society
• /
• v.44 no.1 s.296
• /
• pp.6-11
• /
• 2007

The rheological properties of slag cement pastes by effect of particle size distribution of binder were investigated using a Rheostress 1 rheometer (Haake) with a cylindrical spindle and the relationship between fluidity particle size distribution using the Rosin-Rammler equation. Samples are combined the two types of slag powder and OPC, fine slag particles sized Elaine specific surface area $8,000cm^2/g$, coarse slag particles sized Elaine specific surface area $2,000cm^2/g$, intermediate OPC particles $3,450cm^2/g$, used to search for the combination that would yield the best quality product. The all flow curves which were measured by rheometer showed hysterisis and could be classified into 4 types. When the combination was based on a ratio of 15-20 vol% fine particles, 40-50 vol% intermediate particles, 30-40 vol% coarse particles of the total volume, a high fluidity and low yield-strength was achieved. The Rosin-Rammler function can explain aboved correlation flow curve types. On type 1, the n-value had a correlation with plastic viscosity however the blend of type 2 and 3 showed consistent n-value regardless of plastic viscosity. In addition, the blend in type 4 tended to a rise in fluidity according to the increase of the n-value.