• KIEAE Journal
• /
• v.17 no.1
• /
• pp.15-21
• /
• 2017

Purpose: This study was on the economic feasibility of BIPV system, focused on comparison with construction cost of BAPV system depend on roof finishing materials, and to suggest basic data on the construction cost. Method: Construction cost of BAPV system was calculated, by selecting asphalt single, flat type roof tile, color steel plate, titanium zinc plate as roof finishing material of residential building and by sum up each cost for roof finishing construction and cost for 3kWp-volumed PV module installation. Also, the economic feasibility was analysed quantitatively by comparing the cost for BIPV system construction, installing same volumed PV module instead of roof finishing materials. Result: 1. By installing BIPV system instead of the roof finishing material, the cost of construction falls ; about 19% in case of the titanium zinc plate, which is the most expensive, and about 11% in case of the color steel plate. 2. Reducing amount of the construction cost gets larger because of installing BIPV module instead of the roof finishing material, as the construction cost for roof finishing material gets higher ; therefore, it is more economical than BAPV system in terms of whole cost of construction.

• International journal of steel structures
• /
• v.18 no.4
• /
• pp.1373-1383
• /
• 2018

Experimental study was conducted to investigate the seismic behavior of roof joint. Eight full-scale specimens were tested considering the effects of axial force, joint height, hole shape of base plate and edge distance of concrete on the failure mode and resistance capacity of roof joint. With the increase of axial force, the hysteretic curves were fuller. The mechanical model of roof joint change from bending to shear. With the increase of joint height, the ultimate strength of roof joint decreased. If the hole shape of base plate changed from circle to loose, the slip behavior of roof joint appeared and the ultimate strength of roof joint decreased. The damage of edge concrete may occur if the edge distance of concrete was not big enough.

• Journal of the Korean Institute of Gas
• /
• v.9 no.1 s.26
• /
• pp.33-37
• /
• 2005

This paper deals with parametric studies for the structural response of LNG Storage Tank steel roof behavior acoording to change in design condition. In the design of steel roof, it may be required to represent a stable behavior under many loading conditions and those of combinations. We fulfill the analysis the steel roof behavior during concret placing and additionally change the design variabls like H beam, pressure and steel roof plate thickness. On the basis of the obtained results from this studies a guideline for a more reasonable design of LNG storage tank steel roof is introduced.

• Journal of the Korean Geographical Society
• /
• v.51 no.3
• /
• pp.441-454
• /
• 2016

This study deals with the contemporary rural housing with special reference to the roof types/materials and the outer wall materials in Ulleungdo Mountains. The most frequent roof type of rural housing is the hip-and-gable roof type(42.1%); and the next, the gable roof type(25.8%). For the roof materials, the precoated steel plate(69.1%), the asphalt shingle(11.8%), and the cement(10.7%) are the most frequent but the roofing tile and the artificial slate are not used. And for the outer wall materials, the cement(27.5%), the siding(21.3%), the corrugated galvanized iron(16.8%), and the lumber sheet(6.7%) are the most frequent. It is the hip-and-gable roof housing type with the precoated steel plate(roof materials)(41%), or the hip-and-gable roof housing type with the precoated steel plate(roof materials) and the cement(outer wall material) (18.0%) that is the most frequent type of rural housing in Ulleungdo Mountains. For the roof/wall materials, the ratio of the corrugated galvanized iron is high probably due to the relatively low cost of transport, and the ratio of the roofing tile, the artificial slate, the red brick, and the building stone is very low probably due to the relatively high cost of transport.

• Journal of the Korean Institute of Gas
• /
• v.9 no.2 s.27
• /
• pp.16-21
• /
• 2005

Functions of the compression ring plate fixed at the concrete side wall are to connect and support the steel roof plate. It should be designed to endure stably all the loads such as weight of steel roof, inner pressure and concrete weight. Behavior of the compression ring during construction has been analyzed by the finite element method and real measured data. Additionally, on the basis of results from parametric study of design variables for the steel roof a more reasonable design method for the compression ring has been proposed.

• Current Photovoltaic Research
• /
• v.11 no.2
• /
• pp.54-57
• /
• 2023

Recently, requirements for improving the convenience of constructing BIPV (Building Integrated Photo Voltaic) modules had increased. To solve this problem, we fabricated shingled PV modules integrated with bent steel plates for building integrated photovoltaics. These PV modules could be constructed directly on the roof without the installation structure. We found optimal lamination conditions with supporting structures to fabricate a module on a bent steel plate. Moreover, we applied a shingled design to PV modules integrated with bent steel plates to achieve a high electrical output power. The shingled module with bent steel plates shows 142.80 W of solar-to-power conversion in 0.785 m² area.

• 한국가스학회:학술대회논문집
• /
• 2004.11a
• /
• pp.82-87
• /
• 2004

Compression ring is a part of LNG storage tank. The main function of the compression ring is connected the roof plate with concrete side wall. End of its one side is embedded in the side concrete wall and the other's connected with the roof plate by welding. It is designed to support stably for all the loads such as self weight of steel roof, inner pressure and concrete weight. We fulfill the FEM analysis to analysis the compression ring behavior during construction. Also we studied the effect of the change of design variables. On the basis of the results, we could introduce a more reasonable design method for compression ring.

• Journal of the Korean Institute of Rural Architecture
• /
• v.15 no.3
• /
• pp.17-24
• /
• 2013

This study examined and investigated architectural characteristics such as the use of buildings, the number of layers, and structure, and roof landscape characteristics such as roof types, materials, and color in rural villages which were located on the street on the assumption that the landscape of rural villages should be managed by considering visual aspects. The results were as follows. The commonest frequency was found in 'residence'(2/3) for the use of buildings and 'masonry structure'(2/3) for the structure. 'Wood structure' and 'light gauge steel structure(prefabricated structure)' were also commonly found. The results suggest that although many rural houses have partially improved by agricultural and fishery development projects and garden suburbs has been increased by city residents' desire for rural life, there have been still many old houses. Frequently used roof types were a gambrel roof and a hipped roof. Roof materials were mixed in several materials such as tiles, slate, panels, color steel plate, reinforced concrete, and asphalt shingles. Roof color was also mixed in several colors such as reddish N7 and N0.5 of Neutral color, 10R3/6 and 10R3/10 of R color, 7.5B4/10 and 7.5B7/8 of B color and 5G8/6 of G color. The result suggests that roof color impedes the landscape of rural villages on the street. Based on the results, some roofs of rural villages were improved by the support of the government or the local governments but there are still many old roofs. The mixture of improved roofs and old roofs mainly contributed to impeding the landscape of rural villages and it was probably caused by the lack of systematic landscape plans by individual improvement of buildings. Therefore, it is necessary to devise systematic landscape plans in consideration of local identity and neighboring environment. In particular, the guideline for roof color influencing a street landscape should be established.

• Structural Engineering and Mechanics
• /
• v.7 no.5
• /
• pp.433-445
• /
• 1999

Sandwich panels comprising steel facings and a polystyrene foam core are increasingly used as roof and wall claddings in buildings in Australia. When they are subjected to loads causing bending and/or axial compression, the steel plate elements of their profiled facing are susceptible to local buckling. However, when compared to panels with no foam core, they demonstrate significantly improved local buckling behaviour because they are supported by foam. In order to quantify such improvements and to validate the use of available design buckling stress formulae, an investigation using finite element analyses and laboratory experiments was carried out on steel plates that are commonly used in Australia of varying yield stress and thickness supported by a polystyrene foam core. This paper presents the details of this investigation, the buckling results and their comparison with available design buckling formulae.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.5
• /
• pp.463-469
• /
• 2018

A currently used roof green system with multi layers has a low constructability. Therefore a new integrated waterproof & root barrier sheet and roof green box unit system was developed using steel plate fixture and cone type fixture by electromagnetic induction heating method. This study was proceeded to evaluate adhesion performance of two types of fixtures on Engineering PE, TPO, PVC sheet in a normal condition, repeated heating and cooling condition. As a result, adhesion load on Engineering PE sheet showed the highest value. The adhesion loads of steel plate fixture showed higher value as heating temperature was getting higher. However adhesion loads of cone type fixture showed opposite tendency. Regarding to the test conditions, test results of normal condition, repeated heating and cooling condition showed same value. The cone type fixture using butyl tape showed 7 times lower adhesion load than that of cone type fixture using electromagnetic heating and 28% lower adhesion load in a repeated heating and cooling condition than a usual condition.