• Transactions of Materials Processing
• /
• v.25 no.2
• /
• pp.102-108
• /
• 2016

The aim of the current study was to develop an advanced prediction model for the slab width spread during hot rough rolling. Rough rolling consists of both vertical rolling using a set of profiled edger rolls and horizontal rolling using a set of plain work rolls. FE-simulations were performed to investigate the influences of process variables such as initial slab width, initial thickness, sizing draft, edger roll draft and work roll draft on the final slab width variation. From a statistical analysis of the simulation results, an advanced model, which can predict the slab width spread during the edger rolling and horizontal rolling, was developed. The experimental hot rolling trials showed that the newly developed model provided fairly accurate predictions on the slab width spread during hot rough rolling process using a profiled edger rolls.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1071-1082
• /
• 1988

Surface rolling is one of the micro plastic processes which yields local deformation of surface, and improves surface roughness, hardness and fatigue strength. With the use of gray cast iron (GC 30) as material for experiment, the changes in surface roughness were investigated. A number of previous theses were refered to the effects of surface rolling for this study. With the use of steel ball of excellent in surface roughness and hardness, and with the applied force 20Kgf, surface rolling was performed. The summary of the experiment is as follows: (1) With the fixed applied force 20Kgf and the ball of 8.726mm in diameter, surface roughness was found to be the most excellent. (2) Increase in hardness was most prominent in the first rolling, but less effective in the succeeding rolling. (3) Reduction on diameter was affected by the previous process before rolling, and about 70 to 90% of reduction was made in the first rolling.

• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.155-156
• /
• 2007

This paper presents the vision-based camber and optimal cutting line detection algorithm for hot-rolling process. It is important to measure the camber of head and tail part of strips because many problems are caused by the camber in the hot-rolling process. The hot-rolling process has time constraints. The camber detection algorithm of head and tail parts requires fast and less complex for satisfying time constraints. The proposed algorithm consists of two parts: measurement of the camber in the head and tail part of strips and decision part of the optimal cutting line of hot-rolled strip. First, we obtain the camber value of the strip from the difference between the real center line and the center line of head, tail part. Second, the head and tail part of strips isn't suitable for strips connections. Therefore, the cutting process is needed in the hot-rolling process. The optimal cutting line is determined by the head and tail images obtained from cameras. The algorithm is applied into the vision system with two area cameras, Matrox image processing board and host PC for verification.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.4
• /
• pp.220-230
• /
• 2015

Rolling stock RAMS is a field of engineering which integrates reliability, availability, maintainability and safety (RAMS) characteristics into an inherent product design property through rolling stock system engineering process. It is implemented to achieve operational objectives successfully, and recently the RAMS has become a rapidly growing engineering discipline because it has a great potential to ensure safety and improve cost effectiveness. However, the Korean rolling stock industry has not yet implemented RAMS management in the rolling stock engineering process, despite the issue having been addressed since the introduction of the KTX. Thus, this paper discusses the processes, methods and techniques for RAMS assessment in three parts. Firstly, it outlines a process of the overall RAMS performance assessment for achieving technical RAMS design criteria. Secondly, it discusses a process for assessing the operational RAM and allocating the RAM. This paper also proposes a model for assessing safety-based risk management, which includes five analytic techniques for identifying the causes and consequences of a system failure. Finally, a case example is provided for the risk assessment of the pneumatic braking device.

• Transactions of Materials Processing
• /
• v.26 no.1
• /
• pp.28-34
• /
• 2017

Multi-pass shape rolling is performed to produce long products of arbitrary cross-sectional shapes. In the past, the multi-pass shape rolling process has been designed by the trial and error method or the experience of experts based on the empirical approach. Particularly, the design of roll caliber in shape rolling is important to improve product quality and dimensional accuracy. In this paper, the caliber design and pass schedule of multi-pass shape rolling were proposed for manufacturing piston ring wire. In order to design roll caliber, major shape parameter and dimension was determined by analysis of various caliber design. FE-simulation was conducted to verify effectiveness of proposed process design. At first, forming simulation was performed to predict shape of the product. Then, fracture of the wire was evaluated by critical damage value using normalized Cockcroft-Latham criteria. The experiment was carried out and the results are within the allowable tolerance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.8
• /
• pp.2468-2479
• /
• 1996

An upper bound solution is obtained to perform the process analysis of hot strip rolling process. The material flows within the roll bite at various geometries and frictional conditions are obtained from finite element analysis and the typical flow pattern which is necessary to determine the kinematically admissible velocity field is assumed. From the kinematically admissible velocity field, the upper bound energy is calculated and the rolling load, angle of neutral point and forward slip ratio at various operational conditions are obtained from upper bound energy. The process analysis of above mentioned parameters at various operational conditions have provided valuable information which is hard to obtain during rolling operation and the predicted ranges of quantitive values from these analyses lie whthin the bound of actual operational data.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.69-77
• /
• 1999

Roll profile design in spape rolling with a complex-shaped part depends on the designer's experience, which is general, is acquired through costly trial-and-error process. As a prerequisite for developing a scientific approach to roll profile design, we present a finite element model to simulate 3-D deformation of complex-shaped parts occuring in multi-pass sequence. Demonstrated is the process model's capability to deal with rolling of a complex-shaped part.

• Transactions of Materials Processing
• /
• v.9 no.4
• /
• pp.372-378
• /
• 2000

A process model including the effects of both the texture development and ductile damage evolution In plane strain rolling is presented. In this process model, anisotropy from deformation texture and deterioration of mechanical properties due to growth of micro voids are directly coupled Into the virtual work expressions for the momentum and mass balances. Special treatments in obtaining the initial values of field variables in the nonlinear simultaneous equations for the anisotropic, dilatant viscoplastic deformation are also given. Mutual effects of the texture development and damage evolution during plate rolling are carefully examined in terms of the distribution of strain components, accumulated damage, R-value as well as yield surfaces.

• Transactions of Materials Processing
• /
• v.21 no.3
• /
• pp.179-185
• /
• 2012

In this paper, it is proposed to produce high precision screws with a diameter of $800{\mu}m$ and a thread pitch of $200{\mu}m$ ($M0.8{\times}P0.2$) by means of a cold thread rolling process. In this part II of the study, the focus is on the production and reliability testing of the prototype $M0.8{\times}P0.2$ micro-screw. Designs for two flat dies were developed with the aid of the literature and previous studies. Process parameters during the cold thread rolling process were established through FE simulations. The simulation results showed that the threads of the micro-screw are completely formed through the rolling process. Prototype $M0.8{\times}P0.2$ micro-screw were fabricated with a high precision thread rolling machine. In order to verify the simulation results, the deformed shape and dimensions obtained from the experiment were compared with those from the simulations. Hardness and failure torque of the fabricated micro-screw were also measured. The values obtained indicate that the CAE based process design used in this paper is very appropriate for the thread rolling of micro-sized screws.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.29-34
• /
• 2017

In this paper, we report a method of improving the productivity of lead wire fabricated through the rolling process by increasing its linear velocity. The most important point to consider when raising the linear velocity is that the original specifications must still be adhered to. In other words, the dimensional tolerance must be satisfied when increasing the linear velocity of the wire without causing cracks. However, if the linear velocity of the wire is increased, the degree of reduction must also be increased, which causes more damage to the wire and increases the load on its surface. Therefore, we studied a three step rolling process which can satisfy the specifications of the wire produced through the two step rolling process and improve the productivity. In this study, only the roll gap of the three-stage rolling roller is assumed to be a variable, while the other conditions are the same as the field conditions. In addition, through the PIANO (Process Integration, Design and Optimization) tool, the (optimum?) surface roughness and maximum stress are maintained.