• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.5-13
• /
• 2016

This study is on wear damage of the material for a molding machine that be used at finally cutting of metal beam made in roll forming process of vehicle bump beam process line. SKD11 steel was used with the material for cutting mold jig. In the cutting mold jig, Ti diffusion heat treatment after vacuum heat treatment was carried out for upgrade of surface hardness and anti-wear. Also, the heat treatments by various methods were performed to compare the wear damage degree against above the existing heat treatment. Wear loss and friction coefficient were obtained from wear test. And, micro Vickers hardness values were compared with damaged parts or not of cutting mold jig. Micro Vickers hardness value appeared higher at the undamaged part by Ti diffusion heat treatment. The micro Vickers hardness well followed a two-parameter Weibull probability distribution.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.11
• /
• pp.965-972
• /
• 2016

This paper presents results of flight experiments on a navigation algorithm including multiplicative extended Kalman filter for estimating attitude of the guided munition. The filter describes orientation of aircraft by data fusion with low-cost sensors where measurement update is done by multiplication, rather than addition, which is suitable for quaternion representation. In determining attitude from vector observations, the existing approach utilizes a 3-axis accelerometer as a 2-axis inclinometer by measuring gravity to estimate pitch and roll angles, while GNSS velocity is used to derive heading of the vehicle. However, during accelerated maneuvers such as coordinated flight, the accelerometer provides inadequate inclinometer measurements. In this paper, the measurement update process is newly defined to complement the vulnerability by using different vector observations. The acceleration measurement is considered as a result of a centrifugal force and gravity during turning maneuvers and used to estimate roll angle. The effectiveness of the proposed method is verified through flight experiments.

• Journal of Adhesion and Interface
• /
• v.12 no.2
• /
• pp.47-55
• /
• 2011

UV-curable coatings have been used in various industries due to their advantages such as high mechanical property, good solvent resistance, fast curing process and low volatile organic compounds. However, a lack of flexibility of UV-cured films is a weak point for the pre-coated system of roll-to-roll process. In this study, UV-curable polycarbonate-based methacrylates were synthesized with polycarbonate diol, isophorone diisocyanate and 2-hydroxyethylmethacrylate to improve flexibility of the UC-cured films. The effects of polyol molecular weight, content of photoinitiator and monomers on the UV-curing behavior, flexibility and properties were investigated. The UV-curing behavior was measured by a photo-DSC, the pendulum hardness, tensile strength, viscoelastic properties were also evaluated.

• Journal of Navigation and Port Research
• /
• v.46 no.6
• /
• pp.491-500
• /
• 2022

It has been noted that an accurate estimation of wind loads on offshore structures such as an FLNG (Liquefied Natural Gas Floating P roduction Storage Offloading Units, LNG FPSOs) with a large topside plays an important role in the safety design of hull and mooring system. Therefore, the present study aims to develop a computational model for estimating the wind load acting on an FLNG. In particular, it is the sequel to the previous research by the author. The numerical computation model in the present study was modified based on the previous research. Numerical analysis for estimating wind loads was performed in two conditions for an interval of wind direction (α), 15° over the range of 0° to 360°. One condition is uniform wind speed and the other is the NPD model reflecting the wind speed profile. At first, the effect of sand-grain roughness on the speed profile of the NPD model was studied. Based on the developed NPD model, mesh convergence tests were carried out for 3 wind headings, i.e. head, quartering, and beam. Finally, wind loads on 6-degrees of freedom were numerically estimated and compared by two boundary conditions, uniform speed, and the NPD model. In the present study, a commercial RANS-based viscous solver, STAR-CCM+ (ver. 17.02) was adopted. In summary, wind loads in surge and yaw from the wind speed profile boundary condition were increased by 20.35% and 34.27% at most. Particularly, the interval mean of sway (45° < α <135°, 225° < α < 315°) and roll (60° < α < 135°, 225° < α < 270°) increased by 15.60% and 10.89% against the uniform wind speed (10m/s) boundary condition.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.107-114
• /
• 2000

Rollers and rolls in the continuous process systems are noes of key components that determine the quality of web products. The condition of rollers and rolls(ex. eccentricity wear) should be consistently monitored in order to maintain the process conditions (ex. tension, edge position) within a required specification. In this paper, a new diagnosis technique is suggested to detect the defect of rollers/rolls (ex. eccentricity, wear) based on frequency domain analysis of web tension signal. The kernel of this technique is to use the spectrum amplitude of tension signal which allows to identify the fault rollers/rolls and to also diagnose the degree of fault in corresponding rollers and rolls. The experimental results proved that the suggested diagnosis technique can be successfully used to identify the defect rollers and rolls as well as to diagnose the degree of the defect of those rollers. The suggested technique can be applied to monitor and diagnose the shape of rollers and rolls in various multi-span web transport systems.

• Journal of Information Processing Systems
• /
• v.16 no.5
• /
• pp.1145-1157
• /
• 2020

A convolution neural networks (CNNs) has demonstrated outstanding performance compared to other algorithms in the field of face recognition. Regarding the over-fitting problem of CNN, researchers have proposed a residual network to ease the training for recognition accuracy improvement. In this study, a novel face recognition model based on game theory for call-over in the classroom was proposed. In the proposed scheme, an image with multiple faces was used as input, and the residual network identified each face with a confidence score to form a list of student identities. Face tracking of the same identity or low confidence were determined to be the optimisation objective, with the game participants set formed from the student identity list. Game theory optimises the authentication strategy according to the confidence value and identity set to improve recognition accuracy. We observed that there exists an optimal mapping relation between face and identity to avoid multiple faces associated with one identity in the proposed scheme and that the proposed game-based scheme can reduce the error rate, as compared to the existing schemes with deeper neural network.

• Ceramist
• /
• v.21 no.4
• /
• pp.312-330
• /
• 2018

Energy storage/conversion has become crucial not only to meet the present energy demand but also more importantly to sustain the modern society. Particularly, electrical energy storage is critical not only to support electronic, vehicular and load-levelling applications but also to efficiently commercialize renewable energy resources such as solar and wind. While Li-ion batteries are being intensely researched for electric vehicle applications, there is a pressing need to seek for new battery chemistries aimed at stationary storage systems. In this aspect, Zn-ion batteries offer a viable option to be utilized for high energy and power density applications since every intercalated Zn-ion yields a concurrent charge transfer of two electrons and thereby high theoretical capacities can be realized. Furthermore, the simplicity of fabrication under open-air conditions combined with the abundant and less toxic zinc element makes aqueous Zn-ion batteries one of the most economical, safe and green energy storage technologies with prospective use for stationary grid storage applications. Also, Zn-ion batteries are very safe for next-generation technologies based on flexible, roll-up, wearable implantable devices the portable electronics market. Following this advantages, a wide range of approaches and materials, namely, cathodes, anodes and electrolytes have been investigated for Zn-ion batteries applications to date. Herein, we review the progresses and major advancements related to aqueous. Zn-ion batteries, facilitating energy storage/conversion via $Zn^{2+}$ (de)intercalation mechanism.

• Journal of electromagnetic engineering and science
• /
• v.9 no.1
• /
• pp.17-24
• /
• 2009

In recent years, OFDMA(orthogonal frequency division multiple access) and SC-FDMA(Single Carrier Frequency Division Multiple Access) have been widely studied for the uplink of a mobile communication system. In this paper, PAPR(Peak-to-Average Power Ratio) and BER(Bit Error Rate) performance of the OFDMA and SC-FDMA systems are studied in relation to the uplink of a mobile communication system. Three kinds of sub-carrier allocation methods in the OFDMA system and 2 kinds of sub-carrier allocation methods in SC-FDMA system are suggested to compare and improve system performance. Simulation results show that in the OFDMA system, the first sub-band allocation method has better PAPR reduction performance than the other methods. In the SC-FDMA system, the distributed allocation method offers similar P APR, compared with the sub-band allocation method. P APR can be further reduced by adding a spectrum shaping filter with an appropriate roll of factor. Furthermore, it is found that on average, SC-FDMA can reduce the PAPR by more than 5 dB compared to OFDMA, when the total sub-carrier number is 1,024 and the sub-carrier number allocated to each user changes trom 8 to 512. Because of the frequency diversity and low PAPR characteristics, SC-FDMA system of the distributed sub-carrier allocation method can achieve better BER performance than the OFDMA system.

• Elastomers and Composites
• /
• v.31 no.1
• /
• pp.33-42
• /
• 1996

NR, NBR, and CR rubber were prepared by mixing filler in various ratios. Their vulcanization characteristics and thermal properties were studied. Vulcanization characteristics were investigated using cure curve that had been obtained from oscillating disk rheometer study. The Arrhenius law is known to describe the relationship between cure time and temperature of most elastomers. Curing could be done by the addition of sulfur, peroxides, and proper acceleratores. The optimum cure time that affects desirable values of modulus and tensile strength of the vulcanizate is taken as t90 as measured by a rheometer. Rubbers were cured in the rheometer at temperatures ranging from $130^{\circ}C\;to\;180^{\circ}C$ in order to check the validity of the curing system used. A linear relationship between ln(ts2) and ln(t90) was found for all elastomers. The term sensitivity has been used to describe the relationship between a change of ts2 to the corresponding change of t90 due to an increment of temperature. This is related to the formula of the compound.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.57-61
• /
• 2005

This paper presents a new colonoscopy training simulator that includes a specialized haptic device and graphics algorithms to transfer haptic sensation through a long and flexible tube, and manage large number of polygons. The developed haptic device makes the colonoscope tube move along the two guiding rods in the translational direction. The torque of the roll motion is transferred by a timing belt and pulleys. A special guide is developed, which allows the force and torque from the motors to be transmitted to the user without loss. The haptic device is evaluated by physicians. One of the important skills of the colonoscopy, jiggling is incorporated for the first time by the developed sensor mechanism using photo-sensors. A colonoscope handle that shares the look, feel, and functions with the actual colonoscope, is developed with the necessary electronics inside. The number of polygons is reduced by an edge-collapse algorithm for real-time simulation. The algorithms to import CT data, to segment the colon image, to extract centerline of the colon, and to construct the colon surface, are integrated into a Colon Modeling Kit system that performs all these processes in real-time.