• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.603-610
• /
• 1998

This paper develops a 7 DOF vehicle model to study the effects of the active suspension on ride. The model is used to derive a control law for the active suspension using a full state linear optimal control technique. A wheelbase preview type active suspension is also considered in the control law derivation. The time delay between wheelbases is approximated using Pade approximation technique. The ride model is extended to a 14 DOF handling model. The 14 DOF handling model includes lateral, longitudinal, yaw and four wheel spin motions in addition to the 7 DOF ride model. A control law which is derived considering only ride related parameters is used to study the effects of the active suspension on a vehicle handling. J-turn maneuver simulation results show that the active suspension has a slower response in lateral acceleration and yaw rate, a bigger steady state lateral acceleration and an oversteer tendency. Lane changing maneuver simulation results show that the active suspension has a little bigger lateral acceleration but a much smaller roll angle and roll motion. Braking maneuver simulation results show that the active suspension has a much smaller pitch angle and pitch motion.

• 제어로봇시스템학회논문지
• /
• 제15권2호
• /
• pp.240-248
• /
• 2009

Modem version of supersonic jet fighter aircraft must have been guaranteed appropriate controllability and stability in HAoA(High Angle of Attack). The HAoA flight control law have two parts, one is control law of departure prevention and the other is control law of departure recovery support. The control laws of departure prevention for advanced jet trainer consist of HAoA limiter, roll command limiter and rudder fader. The control laws of departure recovery support are consist of yaw-rate limiter and MPO(Manual Pitch Override) mode. The guideline of pitch rocking using MPO mode is simple, but operating skill of pitch rocking is very difficult by the pilot with inexperience of departure situation. Therefore, automatic deep stall recovery system is necessary. The system called the "Automatic Pitch Rocker System" or APRS, provided a pilot initiated automatic maneuver capable of an aircraft recoveries in situations of deep stall, speed and altitude. This paper addresses the design and validation for APRS to recovery of an deep stall without manual pitch rocking by the pilot. Also, this system is designed to recovery of speed, attitude and altitude after deep stall recovery using ATCS (Automatic Thrust Control System) and autopilot. Finally, this system is verified by real-time pilot evaluation using HQS (Handling Quality Simulator).

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.91-94
• /
• 2005

With increasing demands for large-scale micro-optical components in the field of digital display, the establishment of large-scale fabrication technology fur polymeric patterns has become a priority. The starting point of any polymer replication process is the mold, and the mold often has flat surface. However, It is very hard to replicate large-scale micro patterns using the flat mold, because the cost of large-scale flat mold was very high, and some uniformity and releasing problems were often occurred in large scale flat molding process. In this study, a UV roll imprinting system to overcome the financial and fabrication issues of large-scale pattern replication process was designed and constructed. As a practical example of the system, a lenticular lens with radius of curvature of $223{\mu}m$ and pitch of $280{\mu}m$, which was used to provide wide viewing angle in projection TV, was designed and fabricated. The roll stamper was fabricated using direct machining process of aluminum roll base. Finally, the shape accuracy and uniformity of roll imprinted lenticular lens sheet were measured and analyzed.

• Ocean Systems Engineering
• /
• 제6권3호
• /
• pp.233-244
• /
• 2016

Tension Leg Platform (TLP) is a floating structure that consists of four columns with large diameter. The diffraction theory is used to calculate the wave force of floating structures with large dimensions (TLP). In this study, the diffraction and Froude-Krylov wave forces of TLP for surge, sway and heave motions and wave force moment for roll, pitch degrees of freedom in different wave periods and three wave approach angles have been investigated. From the numerical results, it can be concluded that the wave force for different wave approach angle is different. There are some humps and hollows in the curve of wave forces and moment in different wave periods (different wavelengths). When wave incidents with angle 0 degree, the moment of diffraction force for pitch in high wave periods (low frequencies) is dominant. The diffraction force for heave in low wave periods (high wave frequencies) is dominant. The phase difference between Froude-Krylov and diffraction forces is important to obtain total wave force.

• 제어로봇시스템학회논문지
• /
• 제7권12호
• /
• pp.1044-1050
• /
• 2001

This paper presents firstly the method of Euler angle matching designing the transfer alignment using the attitude matching. In this method, the observation directly uses Euler angle difference between MINS and SINS so it needs to describe the rotation vector error to the Euler angle error. The rotation vector error related to the Euler angle error is derive from the direction cosine matrix error equation. The feasibility of the Kalman filter designed for the transfer alignment by Euler angle matching is analyzed by the alignment error results with respect to the roll angle the pitch angle, and the yaw angle matching.

• 한국추진공학회지
• /
• 제5권1호
• /
• pp.26-33
• /
• 2001

제트베인 추력편향장치는 노즐 뒤에 장착되어 노즐에서 분사되는 초음속 제트의 유동방향을 편향시킴으로써 하나의 노즐로 피치, 요, 롤 방향의 제어를 할 수 있는 장치이다. 제어력을 얻기 위해 초음속 유동중에 노출되어 있는 제트베인에는 열 및 공기역학적 하중이 작용하게 되며, 제트베인의 형상 및 편향각에 따라 나타나는 충격파 및 제트베인 상호 유동간섭으로 인해 비행 추력 손실 및 측력의 크기에 영향을 미치게 된다. 본 연구에서는 마하 2.88 노즐 중에 놓인 제트베인의 피치 및 요, 롤 방향의 특성을 규명하기 위해 6 종의 제트베인을 선정하고, 각 방향에 따른 제트베인 편향각 $0^{\cire}$~$25^{\cire}$ 범위에서 $5^{\cire}$ 간격으로 유동시험을 각각 수행하였다. 또한, 유동해석을 병행하여 제트베인간의 유동 간섭 특성을 분석하였다. 연구 결과 제트베인간의 상호간섭은 나타나지 않으며, 제트베인의 공기역학적 특성은 현과 리드의 길이 비에 크게 좌우되고, 최대 추력손실은 롤 제어시 축추력의 17%로 나타났다.

• Transactions on Control, Automation and Systems Engineering
• /
• 제4권3호
• /
• pp.231-238
• /
• 2002

In this paper, we present a new approach to autopilot design for skid-to-turn missiles which may have severe aerodynamic cross-couplings and nonlinearities with angle of attack. The model of missile motion is derived in the maneuver plane and, based on that model, pitch, yaw, and roll autopilot are designed. They are composed of a nonlinear term which compensates for the aerodynamic couplings and nonlinearities and a linear controller driven by the measured outputs of missile accelerations and angular rates. Besides the outputs, further information such as Mach number, dynamic pressure, total angle of attack, and bank angle is required. With the proposed autopilot and simple estimators of bank angle and total angle of attack, it is shown by computer simulations that the induced moments and some aerodynamic nonlinearities are properly compensated and that the performance is superior to that of the conventional ones.

• International Journal of Aeronautical and Space Sciences
• /
• 제8권1호
• /
• pp.32-45
• /
• 2007

The T-50 advanced supersonic jet trainer employs the Relaxed Static Stability (RSS) concept to improve the aerodynamic performance while the flight control system stabilizes the unstable aircraft and provides adequate handling qualities. The T-50 flight control laws employ a proportional-plus-integral type controller based on a dynamic inversion method in longitudinal axis and a proportional type controller based on a blended roll system with simple roll rate feedback and beta-betadot feedback system. These control laws are verified by flight tests with various maneuver set flight envelopes and the control laws are updated to resolve flight test issues. This paper describes several concepts of flight control laws used in T-50 to resolve those flight test issues. Control laws for solving the roll-off problem during pitch maneuver in asymmetric loading configurations, improving the departure resistance in negative angle of attack conditions and enhancing the fine tracking performance in air-to-air tracking maneuvers are described with flight test data.

• 한국콘텐츠학회논문지
• /
• 제8권2호
• /
• pp.27-32
• /
• 2008

본 논문은 각변위 방식을 이용한 소화경로 모델링 및 경로에 대한 캡슐의 오리엔테이션 측정 방법을 제안하였다. 제안하는 방법은 캡슐 내시경의 자세를 3차원 방향벡터와 이의 회전성분으로 표현하였다. 소화경로에 대한 캡슐의 오리엔테이션 정보인 롤, 피치 그리고 요우 값은 각각 $1.6^{\circ}$ 이내의 오차를 보였다. 제안된 방법은 자기장을 이용한 오리엔테이션 측정에서 롤값 측정 문제를 해결하였다. 오일러 각을 이용한 기존의 오리엔테이션 측정 방식과 비교하여 알고리즘의 복잡도를 줄였다.

• 제어로봇시스템학회논문지
• /
• 제4권5호
• /
• pp.674-679
• /
• 1998

In this paper, a new coarse alignment algorithm is proposed for roughly determining the initial attitude of the vehicle. The algorithm, referred as two-step coarse alignment algorithm, computes roll and pitch angle of the vehicle using accelerometer outputs, and then determines yaw angle with gyro outputs. With the geometric relation between sensor outputs and attitude angles, the algorithm error is analytically derived and compared with the previous coarse alignment algorithm that computes a transformation matrix using accelerometer md gyro outputs simultaneously. The simulation is also performed by varying the sensor errors. The results show that the proposed two-step coarse alignment algorithm has better performance for east tilt angle.