• Journal of the Korean Geotechnical Society
• /
• v.20 no.7
• /
• pp.5-14
• /
• 2004

The observational design and construction method in tunnels is becoming important recently. In many tunnels, enormous cost and time are consumed to cope with the failing or sliding of rock blocks, which could not be predicted because of the complexity of rock discontinuities. It is difficult to estimate the properties of rock masses before the construction. In this paper, a new observational design and construction method in tunnels are proposed, and then applied to the example of the very large cross section tunnel based on actual discontinuity information observed in situ. The items examined in developing a program for the new observational design and construction method are the following ones: generality, precision, high speed, and friendly usability. At the very large cross section tunnel, 7 key blocks were judged to be unstable because they could not be supported by standard supports. Supplementary supports were installed to these 7 key blocks before the excavation. It is possible to detect key blocks all along the tunnel exactly by using the numerical analysis program developed for the new observational design and construction method in the very large cross section tunnel. This computer simulation method with user-friendly interfaces can calculate not only the stability of key blocks but also the design of supplementary supports.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.2
• /
• pp.57-65
• /
• 2022

This study simulated the shock wave propagation through the tamping material between explosives and hole wall at blasting works and verified the effect of tamping materials. The Arbitrary Lagrangian-Eulerian(ALE) method was selected to model the mixture of solid (Lagrangian) and fluid (Eulerian). The time series analysis was carried out during blasting process time. Explosives and tamping materials (air or water) were modeled with finite element mesh and the hole wall was assumed as a rigid body that can determine the propagation velocity and shock force hitting the hole wall from starting point (explosives). The numerical simulation results show that the propagation velocity and shock force in case of water were larger than those in case of air. In addition, the real site at blasting work was modeled and simulated. The rock was treated as elasto-plastic material. The results demonstrate that the instantaneous shock force was larger and the demolished block size was smaller in water than in air. On the contrary, the impact in the back side of explosives hole was smaller in water, because considerable amount of shock energy was used to demolish the rock, but the propagation of compression through solid becomes smaller due to the damping effect by rock demolition. Therefore, It can be proven that the water as the tamping media was more profitable than air.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.2 no.1
• /
• pp.88-93
• /
• 1999

In modern period, the history of highway landscaping can be divided into three stages. The first stage from the late 1960s to the early 1970s : during this period revegetation operation started and landscape architecture was introduced. The second stage from the late 1970s to the early 1980s : during this period the definition of functional planting which had played the most important role in highway landscaping was established. Also, highway landscaping was influenced by Japan, and the revegetation of highway slopes were applied with Seedspray, Block-sodding methods, and so on. The third stage from late 1980s to the present : during this period eco-landscaping was introduced and began to mix with ecosystem techniques. The revegetation works of cutting-rock slopes have widely been developed. Many people think that landscaping is necessary for us, and that revegetation method is effective to conserve slope environment. Based on accumulated data we have to improve the function of landscaping and revegetation method, and also have to establish the method of landscaping harmonized with our own landscape.

• Journal of the Korean Institute of Rural Architecture
• /
• v.11 no.2
• /
• pp.1-8
• /
• 2009

This paper evaluate use on facilities of green tourism by participator's questionnaire and urban inhabitants' questionnaire. As the result of study, it shows follows; 1) To make town look more traditionally we should rebuild the buildings and the styles of roof with our own traditional rural system. And, we also change the block and brick style fence into soil or rock one instead to look rural path. The agricultural land and watercourse should be left naturally to be looked non-polluted environment. 2) The outdoor toilet, washing stand and distribute should be maintained and managed clearly every time. Residents' own housing also should be maintained to promote the home-stay lodging. 3) To improve the satisfaction of people's need of agricultural product, the special market building or place that could be packed and sold the product at the same time should be built or made. And, it should be located in the harmonious spot with the natural scenery and good parking lot.

• Geomechanics and Engineering
• /
• v.16 no.1
• /
• pp.49-58
• /
• 2018

Open-mode cracks could be commonly observed in layered rocks. A concept model is firstly used to explore the mechanism of the vertical cracks (VCs) in the top layer. Then the crack behaviour of the two-layer model is simulated based on a cohesive zone model (CZM) for layer interfaces and a plastic-damage model for rocks. The model indicates that the tensile stress normal to the VCs changes to compression if the crack spacing to layer thickness ratio is lower than a threshold. The results indicate that there is a threshold for interfacial shear strength that controls the crack patterns of the layered system. If the shear strength is lower than the threshold, the top layer is meshed by the VCs and interfacial cracks (ICs). When the shear strength is higher than the threshold, the top layer is meshed by the VCs and parallel cracks (PCs). If the shear strength is comparative to the threshold, a combining pattern of VCs, PCs and ICs for the top layer can be formed. The evolutions of stress distribution in the crack-bound block indicate that the ICs and PCs can reduce the load transferred for the substrate layer, and thus leads to a crack saturation state.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.34-41
• /
• 2006

A 3-dimensional stress measurement system based on the bore hole bottom deformation method, which is one of the stress relief methods, was developed. A pilot bore hole is drilled from the bottom of a bore hole and the stress meter is inserted into the pilot bore hole in the method. The bore hole is advanced as an over coring and the deformations in seven directions are measured by cantilever type-sensors. Using the cantilever type-sensors saves time for hardening of glue. No cable connection between the stress meter and a data logger is necessary since a compact data logger is installed in the stress meter. The accuracy of the stress meter was confirmed by a biaxial test for a Shikotsu welded tuff block although in-situ tests have not been carried out yet.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.2
• /
• pp.295-303
• /
• 2013

This paper reports an investigation of pulse width modulation (PWM) techniques for two-phase brushless DC (BLDC) motors fed by a two-phase eight-switch inverter in a fan application. The three-phase BLDC motor is widely applied in industry; however, a lower-cost two-phase BLDC motor and drive circuit has been greatly in demand in recent years. In this paper, we introduce a mathematical model of the two-phase BLDC motor with sinusoidal back electromotive forces (EMFs) based on traditional three-phase BLDC motors. To simplify the drive algorithm and speed up its application, we analyze the principle of block commutation for a two-phase BLDC motor drive in the 180-electrical-degree conduction mode, and we further propose five PWM schemes to improve the commutation performance of the two-phase BLDC drive. The effectiveness of the proposed PWM methods is verified through experiments.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.695-702
• /
• 2002

Groundwater flow is primarily influenced by the presence of fractures, functioning as conduits. To block the flow, grouting operation is commonly used. Thereby the fractures are then expected to be sealed, which will add to enhance the shear strength in rock. This far, regarding the assessment of grouting efficiency, however, there's been a considerable uncertainty That is, several geophysical methods of high resolution such as tomography, S-wave logging have produced a significant amount of measurable response caused by grouting, but they can inevitably be used only for the qualitative assessment. Thus, this paper deals with an accurate quantitative assessment about the grouting result. In this, a new strategy is introduced, based mainly on evaluating the opening of fractures. For fracture-opening investigation purposes, borehole Televiewer has already proven to be an excellent logging technique that produces both amplitude image and traveltime image. As well known, the traveltime image can be converted to a high precision 3D caliper log with max. 288 arms, which allows to observe the opening of fractures. To evaluate the fracture opening from the traveltime image, an algorithm of practical use was developed, in which image correction due to the borehole deviation, feature discrimination of wall roughness from fractures, automatic evaluation procedure etc. were considered. Field examples are shown to confirm the efficiency of the suggested method.

• Journal of the Korean Society of Safety
• /
• v.25 no.2
• /
• pp.55-64
• /
• 2010

Since various weathered soils are encountered in many domestic construction sites, it is necessary to estimate characteristics of natural weathered soils. However, the remolded sample of weathered soils are commonly used to estimate their characteristics because it is very difficult to sample weathered soils in undisturbed states. However, it is well known that the behavior of remolded sample is different from that of the undisturbed sample particularly in the dynamic response, because the particle structure of undisturbed sample maintains its original structure from the mother rock. Thus, to evaluate the influence of sampling method and preparation method on stress-strain behavior, the resonant column tests were performed on the block, tube samples, remolded samples with static compression and remolded samples with tamping of the weathered granite soils. The shear modulus of the remolded sample with tamping is larger than the other samples presumably due to the high tamping pressure enough to induce particle breakage. The tube samples show larger damping ratios than other samples. Furthermore, one-dimensional ground response analysis was performed to compare the results qualitatively.

• Geomechanics and Engineering
• /
• v.13 no.6
• /
• pp.997-1010
• /
• 2017

The black box model is a relatively new option for nonlinear dynamic system identification. It can be used for prediction problems just based on analyzing the input and output data without considering the changes of the internal structure. In this paper, a black box model was presented to solve unconstrained overlying strata movement problems in coal mine production. Based on the black box theory, the overlying strata regional system was viewed as a "black box", and the black box model on overburden strata movement was established. Then, the rock mechanical properties and the mining thickness and mined-out section area were selected as the subject and object respectively, and the influences of coal mining on the overburden regional system were discussed. Finally, a corrected method for height prediction of the fractured zone was obtained. According to actual mine geological conditions, the measured geological data were introduced into the black box model of overlying strata movement for height calculation, and the fractured zone height was determined as 40.36 m, which was comparable to the actual height value (43.91 m) of the fractured zone detected by Double-block Leak Hunting in Drill. By comparing the calculation result and actual surface subsidence value, it can be concluded that the proposed model is adaptable for height prediction of the fractured zone.