• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.1
• /
• pp.77-84
• /
• 2015

In 2011, greenhouse gas emissions of transport sector were 85.04 million $tonCO_2eq$ and road emissions accounted for 95% of total emissions in the transport sector. There are few innovative technologies to reduce greenhouse gas emissions aside from eco-driving education and public relation program. Therefore, this paper focused on analyzing optimal acceleration by certain road grades and suggested fuel-efficient driving method for various uphill sections. Scenarios were established by driving modes. Speed profiles were generated by scenarios and speed variations. Each speed profile applied to Comprehensive Modal Emission Model and then each fuel consumption was estimated. Driving mode and speed variation that minimized fuel consumption were driven according to grade percent and uphill distance. When driving in the eco-friendly mode of the driving and speed variation, reduction rate of fuel consumption was evaluated by comparison between eco-driving and cruise control mode. When a vehicle drove under eco-driving mode at 100kph, 90kph and 80kph on uphill road, fuel consumptions were reduced by 33.9%, 30.8% and 5.3%, respectively.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.3
• /
• pp.323-335
• /
• 2020

In this study, a series of site measurement of particulate and gases pollutants at five tunnels were carried out along with case studies to review the suitability of the current road tunnel ventilation design standards. Previous studies by other researchers have shown that the ratios of the level of measurement to the standard were 27.9%, 1.6% and 3.4% for TSP, CO and NOx, respectively. Those measured in this site study shows even lower ratios; the ratios were 2.6%, 0.8% and 0.3%, for TSP, CO and NOx, respectively. The particle size analysis of TSP for the five tunnels shows that PM10 including tire wear and re-suspended road dust exceeded 20.4%. This implies that non-exhaust particulate matter must be taken into account, since the current design standards for the particulate matter (visibility) include only the engine emission. Based on the recent research results, for vehicle emission rate and slope-speed correction factors, revision of ventilation design standards for pollutants is required. WRA (PIARC) also emphasizes the necessity of the ventilation design standards for pollutants. In addition, enactment of a new road tunnel ventilation system operation standard or guideline is strongly recommended when considering the low operating rate of the ventilation system with jet-fans.

• Journal of Korean Society of Transportation
• /
• v.23 no.2
• /
• pp.95-106
• /
• 2005

Road accidents are considered as the result of a complex interplay between road, vehicle, environments, and human factors. Little study, however, has been carried out on the attributes of human factor compared to the road geometric conditions and traffic conditions. The previous researches focused on mainly both traffic and geometric conditions on specific location. Therefore, it's hard to explain phenomenon of the high traffic accident rates where road and traffic conditions are good. Because of these reasons, accident analysis has contributed on geometric improvement and has not contributed on traffic management such as selection of attention section, driver napping alert, etc. The freeway incident management is also associated with reliable prediction of incident occurrences on freeway sections. This paper presents a method for estimating the effect of trip length on freeway accident rate. A PAR (Potential Accident Ratio), the new concept of accident analysis, considering TLFDs (Trip Length Frequency Distributions) is suggested in this paper. This approach can help to strengthen freeway management and to reduce the likelihood of accidents.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.40 no.2
• /
• pp.119-133
• /
• 2022

Due to the improvement of surveying, mapping and communication techniques, various apps for road direction guides and vehicle navigations have been developed. Although such a development has impacted on walking and driving, there is a limit to improving the daily convenience of the socially impaired people. This is mainly due to the fact that the software have been developed for normal pedestrians and drivers. Therefore, visually impaired people still have problems with the confusion of direction and/or non-provision of risk factors in walking. This study aimed to propose a scheme which constructs data for mobility-impaired or traffic-impaired people based on various geospatial information. The factors and components related to walking for the visually impaired are selected by geospatial data and a walking route guidance network that can be applied to a commercial software. As a result, it was confirmed that road direction guidance would be possible if additional contents, such as braille blocks (dotted/linear), sound signals, bus stops, and bollards are secured. In addition, an initial version of the application software was implemented based on the suggested data model and its usefulness was evaluated to a visually impaired person. To advance the stability of the service in walking for the visually impaired people, various geospatial data obtained by multiple institutes are necessary to be combined, and various sensors and voice technologies are required to be connected and utilized through ICT (Information and Communications Technologies) technology in near future.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.3A
• /
• pp.305-313
• /
• 2008

A reliability based calibration of dynamic load allowance (DLA) of highway bridge is performed by numerical dynamic analysis of various types of bridges taking into account of the road surface roughness and bridge-vehicle interaction. A total of 10 simply supported bridges with three girder types in the form of prestressed concrete girder, steel plate girder, and steel box girder is analyzed. The cross sections recommended in "The Standardized Design of Highway Bridge Superstructure" by the Korean Ministry of Construction are used for the prestressed concrete girder bridges and steel plate girder bridges while the box girder bridges are designed by the LRFD method. Ten sets of road surface roughness for each bridge are generated from power spectral density (PSD) function by assuming the roadway as "Average Road". A three dimensionally modeled 5-axle tractor-trailer with its gross weight the same as that of DB-24 design truck is used in the dynamic analysis. For the finite element modeling of superstructure, beam elements for the main girder, shell elements for concrete deck, and rigid links between main girder and concrete deck are used. The statistical mean and coefficient of variation of DLA are obtained from a total of 100 DLA results for 10 different bridges with each having 10 sets of road surface roughness. Applying the DLA statistics obtained, the DLA is finally calibrated in a reliability based LRFD format by using the formula developed in the calibration of OHBDC code.

• Journal of Navigation and Port Research
• /
• v.26 no.3
• /
• pp.323-328
• /
• 2002

Soil-steel structures have been used for the underpass, or drainage systems in the road embankment. This type of structures sustain external load using the correlations with the steel wall and engineered backfill materials. Buried flexible conduits made of corrugated steel plates for the coastal road was tested under vehicle loading to investigate the effects of live load. Testing conduits was a circular structure with a diameter of 6.25m. Live-load tests were conducted on two sections, one of which an attempt was made to reinforce the soil cover with the two layers of geo-gird. Hoop fiber strains of corrugated plate, normal earth pressures exerted outside the structure, and deformations of structure were instrumented during the tests. This paper describes the measured static and dynamic load responses of structure. Wall thrust by vehicle loads increased mainly at the crown and shoulder part of the conduit. However additional bending moment by vehicle loads was neglectable. The effectiveness of geogrid-reinforced soil cover on reducing hoop thrust is also discussed based on the measurements in two sections of the structure. The maximum thrusts at the section with geogrid-reinforced soil cover was 85-92% of those with un-reinforced soil cover in the static load tests of the circular structure; this confirms the beneficial effect of soil cover reinforcement on reducing the hoop thrust. However, it was revealed that the two layers of geogrid had no effect on reducing the overburden pressure at the crown level of structure. The obtained values of DLA decrease approximately in proportion to the increase in soil cover from 0.9m to 1.5m. These values are about 1.2-1.4 times higher than those specified in CHBDC.

• Journal of Korean Society of Transportation
• /
• v.25 no.6
• /
• pp.79-88
• /
• 2007

Design Hourly Volume (DHV) is the hourly volume used for designing a section of road. DHV is also used to estimate the expected number of vehicles to pass or traverse the relevant section of road in a future target year. The Design Hour Factor (DHF) is defined as the ratio of DHV to Average Annual Daily Traffic (AADT). In addition to high precision of predicted traffic volume, in order to design a roadway to be the proper scale, applying appropriate DHFs considering traffic flow characteristics and type of area which surrounds the relevant roadway is important. This study categorizes sections of expressway (Suh Hae An Expressway) according to their area type and estimates DHFs utilizing traffic data obtained from a vehicle detection system (VDS). This study shows that DHFs calculated using VDS data are different from those using traffic data acquired from a coverage survey. While AADTs from both data show similar values, peak hour volumes from both data show significant differences especially for recreational areas. DHFs from the coverage survey are quite different from the values provided by the Korean design guide or previous research results and DHFs for urban areas are higher than recreational areas. However, DHFs from VDS shows similar values to previous research results. The result of this study suggests that using VDS for estimating DHFs is more reliable than using a coverage survey.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.12
• /
• pp.2779-2784
• /
• 2015

The prediction of the accurate traffic information can provide an optimal route from the place of departure to a destination, therefore, this makes it possible to obtain a saving of time and money. To predict traffic information, we use a Bayesian network method based on probability model in this paper. Existing researches predicting the traffic information based on a Bayesian network generally used to study the data for all time. In this paper, however, only data corresponding to same time and day of the week to predict selectively will be used for learning. In fact, the experiment was carried out for 14 links zone in Seoul, also, the accuracy of the prediction results of the two different methods should be tested with MAPE (Mean Absolute Percentage Error) which is commonly used. In view of MAPE, experimental results show that the proposed method may calculate traffic prediction value with a higher accuracy than the method used to learn the data for all time zones.

• Journal of Environmental Impact Assessment
• /
• v.27 no.5
• /
• pp.431-446
• /
• 2018

In this study, chemical characteristics of $PM_{2.5}$ samples collected in an agricultural area in Nonsan of Korea were investigated focusing on of black carbon, 3 inorganic ions and 22 trace elements. It was found that the relative error and relative standard deviation of many trace elements fell below 10%, which indicates good analytical accuracy and precision. The mean values of $PM_{2.5}$ in an agricultural area were exceeded by new Korean air quality standard of March 2018. The concentration of $PM_{2.5}$ was well correlated with those of black carbon and ions. The concentrations of trace elements were in a wide range of seven orders of a magnitude. Based on these $PM_{2.5}$ data sets, a total of 6 sources were identified using PMF (Positive Matrix Factorization; secondary aerosol (34.4%), soil/road dust (20.1%), biomass burning (16.9%), incineration/fuel combustion (13.2%), vehicle exhaust(12.2%), sea-salt (3.17%). Results of our study indicate that it is very important to control illegal burning activities in agricultural area.

• Journal of Korean Society of Transportation
• /
• v.36 no.1
• /
• pp.38-50
• /
• 2018

Emerging automated driving environments will lead to a mixed traffic flow depending on the interaction between automated vehicles (AVs) and manually driven vehicles (MVs) because the market penetration rate (MPR) of AVs will gradually increase over time. Understanding the characteristics of mixed traffic conditions, and developing a method to control both AV and MV maneuverings smoothly is a backbone of the traffic management in the era of automated driving. To facilitate smooth vehicle interactions, the maneuvering of AVs should be properly determined by various traffic and road conditions, which motivates this study. This study investigated whether the aggressiveness of AV maneuvering, defined as automated driving aggressiveness (ADA), affect the performance of mixed traffic flow. VISSIM microscopic simulation experiments were conducted to derive proper ADAs for satisfying both the traffic safety and the operational efficiency. Traffic conflict rates and average travel speeds were used as indicators for the performance of safety and operations. While conducting simulations, level of service(LOS) and market penetration rate(MPR) of AVs were also taken into considerations. Results implies that an effective guideline to manage the ADA under various traffic and road conditions needs to be developed from the perspective of traffic operations to optimize traffic performances.