• Journal of Korean Society of Transportation
• /
• v.24 no.6 s.92
• /
• pp.33-43
• /
• 2006

This research is to the selection of optimal probability distribution as well as the estimation for design hourly factor in consideration of traffic characteristic, such as road function, lane number and AADT. To accomplish the objectives, we are applied to various probability distribution using traffic data that observed at permanent traffic count points in 2005. The parameters or the selected 14 probability distribution were estimated based on the method of maximum likelihood and the validity condition of the estimated parameter The goodness-of-fit test, such as chi-square test. was performed as well as the estimation of design hourly factor. As a result, An appropriate distributions of each case were selected : Pearson V for two lane of rural roads, LogLogistic for the four lane of rural roads, LogLogistic for the urban roads, Extreme value for recreation roads. And optimal K factor are as following : $0.1{\sim}0.2 $ for two lane of rural roads, $0.09{\sim}0.14$ for the four lane of rural roads. $0.07{\sim}0.13$ for the urban roads, $0.1{\sim}0.2$ for recreation roads.

• International Journal of Highway Engineering
• /
• v.13 no.1
• /
• pp.119-127
• /
• 2011

The main purpose of this paper is to apply Zone 30 system which is being experimented in advanced country for the solution of controlling the residential street's speed to our country with the consideration of the real condition of our street and traffic and to run this system as an example to analyze the effect and at the same time, analyze the problem and get appropriate preparation for this system to be widespread. The area to run this model project is Goyang City Ilsan-Gu.($0.65km^2$) which is close with the commercial area reflecting the opinion of experts and an on-site verification by the National Police Agency T/F and is having a heavy pedestrian traffic and the risk of pedestrian accident. Firstly we defined residential street and residential street area to review the system and devided the residential street type to establish a plan of operation. Afterwards, we thoroughly examined the model project area and analyzed the problem and solution. We finally completed establishing a facilities by conference with a local autonomous entity with the improvement of facility's sketch at the analysis of the model project area. The result of effects analysis which we devided after and before of establishment is that vehicle speed be reduced 5~15km/h, and traffic accidents has decreased by 24 percent.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.4
• /
• pp.61-70
• /
• 2008

This paper designed the antenna for collecting and servicing the traffic information that apply to freeway Traffic Management System, as using DSRC (Dedicated Short Range Communication). Active DSRC is the technology that is using 5.8GHz Radio Frequency to a mean Sequency and there are a lot of the case occurring a physical electric wave shadowing because of the traveling straight of a electric wave. In such inferior communication environment, it constructed the stabilized communication link that can do collecting and servicing the correct traffic information and designed the beam pattern considering the establishment position of the antenna that can apply to various road environments and a communication area. By considering the communication link environment, this paper designed and manufacture the mean frequency of 5.8GHz, the input loss of -17dB in 75MHz bandwidth, the Axial ratio of 1.5:1, and $2{\times}4$ array microstrip antenna which beam pattern have the characteristic of $55^{\circ}$ horizontal half power beam width and $26^{\circ}$elevation half power beam width and the minimum establishment height of the antenna was designed as 14m for avoiding electric wave shadowing on a physical condition between vehicles

• Korean Journal of Culture and Social Issue
• /
• v.16 no.1
• /
• pp.1-18
• /
• 2010

This study examines the characteristics of traffic accidents involving elderly pedestrians by analyzing relevant data vis-à-vis fatal pedestrian accidents and proposes solutions to reduce such accidents. We analyzed 3,853 cases of fatal accidents involving elderly pedestrians and 1,786 cases involving younger pedestrian (these cases reflect accidents that occurred from 2005 to 2008). The results show that accidents involving the elderly occur more frequently in rural areas than urban areas, especially in autumn; this condition applies even in situations where the elderly exhibit compensation behaviors such as walking on safer roads. We found that elderly pedestrians exhibit a defective behavior in crossing roads, especially in complicated road conditions where intersections and turning/reversing vehicles represent a menacing threat. These characteristics could be explained by the degenerated physical/mental ability of the elderly and by psychological factors such as reduced level of self-confidence.

• Journal of the Korea Society of Computer and Information
• /
• v.22 no.9
• /
• pp.99-105
• /
• 2017

In this paper, we propose to design and implement the database management system for analyzing vehicle accidents through utilizing integration of the public big data. And the paper aims to provide valuable information for recognizing seriousness of the vehicle accidents and various circumstances at the accident time, and to utilize the produced information for the insurance company policies as well as government policies. For analysis of the vehicle accidents the system utilizes the integrated big data of National Indicator System, the Meteorological Office, National Statistical Office, Korea Insurance Development Institute, Road Traffic Authority, Ministry of Land, Infrastructure and Transport as well as the National Police Agency, which differentiates this system from the previous systems. The system consists of data at the accident time including weather conditions, vehicle models, age, sex, insurance amount etc., by which the database system users are able to obtain the integral information about vehicle accidents. The result shows that the vehicle accidents occur more frequently in the clear weather conditions, in the vehicle to vehicle conditions and in crosswalk & crossway. Also, it shows that the accidents in the cloudy weather leads more seriously to injury and death than in the clear weather. As well, the vehicle accident information produced by the system can be utilized to effectively prevent drivers from dangerous accidents.

• International Journal of Highway Engineering
• /
• v.12 no.1
• /
• pp.47-54
• /
• 2010

This study had a focus on investigating technical validity of Two-Lift Concrete Pavements which had never been constructed in Korea in order to olve the problem of existing concrete pavements. This study found out the application of Steel Fiber Reinforced Concrete (SFRC) which was one of ew techniques. Also, optimal steel fiber contents and pavement thickness were determined. This study also measured compressive strengths, lexural strengths, toughness indexes, tensile strengths and fatigue strengths to estimate the performance of SFRC of according to results of aboratory experiments, slumps and air contents of concrete specimens the standards satisfied and compressive strengths to open traffic. At bending ests, Toughness Index of SFRC increased but flexural strength didn’'t increase as compared with non-steel fiber concretes. And, energy absorption of SFRC was very good and SFRC showed improvement in freezing and thawing resistances. To complete this research, we will evaluate the pplication methods and performance of SFRC at field section.

• Journal of the Korean Society for Railway
• /
• v.12 no.6
• /
• pp.1024-1029
• /
• 2009

According to increase of massive concrete structures, Thermal crack done by heat of hydration have been increased in a process of the execution. In case of a subway concrete box structure, thickness of structures are almost over 1 meter, and penetrating crack by external restraint takes a bad effect on the durability with a water leakage and deterioration in especially concrete wall. A try of shortening a constructing period often occurs as subway is generally constructed according to a road to decrease a traffic jam. The research proposes executing method by skipping one block as a plan of shortening a constructing period and investigate an influence on thermal cracking control. Additionally, sensitivity analysis is accomplished by changing a height of a concrete wall, and concrete placing and air temperature met with a field condition.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.123-132
• /
• 2011

The purpose of this study is to calculate and propose rational multi-lane loading factors for bridge design considering the probability of simultaneous truck passing in adjacent lanes and real truck weights. The probability of simultaneous truck passing is calculated by analyzing video image taken at various locations in highways and national roads. Weigh-In-Motion system data at two locations are used, which is combined with the probability of multiple presence to calculate the multi-lane loading factors for typical 2 lane and 5 lane bridges. Statistical properties of multi-lane loading factors are also calculated assuming that locations for video images and WIM data represent the overall traffic condition in the country. Results are compared with various design codes in the world and they show that the values are between the current Korea Bridge Design Code and AASHTO LRFD specification or Eurocode and are similar to Canadian Code.

• International Journal of Highway Engineering
• /
• v.6 no.3 s.21
• /
• pp.27-35
• /
• 2004

There are two methods in estimating the remaining life of in-service airfield concrete pavement. They are a method simply using the past accumulated traffic and a method using the theoretical mechanistic analysis. Since the former method is somewhat far from the actual condition, the latter method is widely used by most engineers and researchers. The most essential component of the latter method is the fatigue model of the concrete slab. A fatigue model for airfield concrete pavement is developed in this study by a series of fatigue tests using 30 concrete cylinder specimens obtained from a 10 year old in-service airfield concrete slab. Strengths for the stress ratio calculation were obtained from the split tensile test of the cores sliced. Fatigue test mode was repeated split tensile test. The R2 of developed fatigue model was 0.5. Specimens taken from another airport had been tested for validation of the model. The results showed a good fit to the model. It was also found that the fatigue life predicted from the model was a tittle greater when the stress ratio is greater than 80 percent than other fatigue models developed earlier in America.

• International Journal of Highway Engineering
• /
• v.16 no.6
• /
• pp.121-128
• /
• 2014

PURPOSES : The objective of this study is to evaluate the tack-coating material's properties using the bitumen bond strength(BBS) test and damping test as function of changed curing times. In this study, bonding strength tests were performed according to the curing time of tack coating materials. METHODS : In order to investigate bonding characteristic of tack coating materials, the Pneumatic Adhesion tensile Testing Instrument(PATTI) device is used to measure the bond strength between the tack coating materials and aggregate substrate based on the AASHTO TP-91. Also, damping test as in situ test was used to determine an appropriate traffic openting time for construction vehicle. Four different tack-coating materials were used in this study. The BBS tests were performed a one hour curing and testing temperatures of $5^{\circ}C$, $15^{\circ}C$, and $25^{\circ}C$. Damping test was conducted at 30min, 60min, 90min, and 120 min of curing times with temperatures of $20^{\circ}C$ and $30^{\circ}C$. RESULTS and CONCLUSIONS : The BBS test results show various bond strength as function of tack coat materials. At the same testing condition, A tack coat material shows almost two times higher than D tack coat materials although both materials are satisfied the criteria of material's physical properties. Also, Dampting test results shows similar trend with BBS test result. The damping test result was significantly changed as function of tack coat materials. Based on this study, the tack coating material's curing time is very important. Therefore, both curing time and the bond strength's characteristic has to be considered in standard specification.