• Journal of the Korea Institute of Building Construction
• /
• v.20 no.4
• /
• pp.375-382
• /
• 2020

Rock drop obstacles on major roads in the border area in South Korea has been installed and operated to prevent and block the movement of enemy units. However, the increase in traffic volume due to the development of the border region causes many problems such as road traffic congestion due to rock drop, traffic safety, and impaired urban aesthetics. Therefore, this study aimed to provide guidelines for demolition and replacement facility installation for rock drop obstacles, which are differently applied to each unit, and to suggest the direction of the Ministry of National Defense's policy regarding maintenance cost for necessary rock drop obstacles required for operation. In this study, as part of a guideline study on the removal of rock drop obstacles and the installation of alternative facilities, a standard unit price was suggested for essential rock drop obstacles, so as to be used as judgment data when deciding whether to remove rock drop obstacles.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.109-110
• /
• 2023

Domestic ultra-hard road repair materials require a lot of time before the road can be opened to traffic. Therefore, in this study, Methyl Methacrylate (MMA) based road repair material was used to improve the above problems. Furthermore, the basic physical properties of MMA-based pavement repair materials are examined to confirm their suitability in concrete pavements. For this study, two types of MMA road repair materials (A type and B type) were selected. Then, the curing of the test specimens prepared for painting was carried out under three conditions. The experimental items were viscosity (drop time) and drying time (set to touch, dry-hard). As a result of the experiment, viscosity (drop time) was faster in type A than in type B. The drying time results were as follows. In the case of set ti touch, both type A and type B dried in about 10 minutes regardless of the curing conditions. In the case of dry-hard, regardless of the curing conditions, A type dried longer than B type, but it dried faster than conventional road repair materials. Therefore, within the scope of this study, it is considered that A type has a high potential for utilization as a road repair material.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.39-46
• /
• 2010

In 2007, Iowa department of transportation (DOT) initiated to run the falling weight deflectometer (FWD) network-level testing along Iowa highway and road systems and to build a comprehensive database of deflection data and subsequent structural analysis, which are used for detecting pavement structure failure, estimating expected life, and calculating overlay requirements over a desired design life. Iowa's current FWD networklevel testing protocol requires that pavements are tested at three-drop level with 8-deflection basin collected at each drop level. The test point is determined by the length of the tested pavement section. However, the current FWD network-level program could cover about 20% of Iowa's highway and road systems annually. Therefore, the current FWD network-level test protocol should be simplified to test more than 20% of Iowa's highway and road systems for the network-level test annually. The main objective of this research is to investigate if the minimum number of drop levels and test points could be reduced to increase the testing production rate and reduce the cost of testing and traffic control without sacrificing the quality of the FWD data. Based upon the limited FWD network-level test data of eighty-three composite pavement sections, there was no significant difference between the mean values of three different response parameters when the number of drop levels and test points were reduced from the current FWD network-level testing protocol. As a result, the production rate of FWD tests would increase and the cost of testing and traffic control would be decreased without sacrificing the quality of the FWD data.

• Korean System Dynamics Review
• /
• v.12 no.1
• /
• pp.75-87
• /
• 2011

Congestion problems can be approached from the viewpoint of system dynamics theory. The relationship between road capacity and congestion can be explained by the 'relative control' archetype among four system archetypes suggested by Wolstenholme. There is a balancing feedback loop between road capacity and road congestion. However, there is another balancing loop between road congestion and car traffic volume, which keeps disrupting the equilibrium of the former loop. A system dynamics model, which is based on a partial adjustment model of induced traffic in the literature, is built to simulate three road building scenarios: 'Expanding investment', 'Balancing investment' and 'Frozen road investment' scenarios. The 'Expanding investment' scenario manages to drop congestion levels by 9% over 30 years, however, causing much higher emissions of $CO_2$ than other scenarios. The trade-off relationship between congestion levels and environmental costs must be taken into consideration for road investment policies.

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.37-45
• /
• 2016

Exhaust gas recirculation has the advantage of being low-cost and easy to control of NOx emission. Therefore, it is most generally used to reduce NOx emission according to strengthen regulation. In the case of a non-road engine, such as the agricultural engine, since it mainly operate a middle or high-load state, NOx emission is decreased in accordance with the mapping range of the EGR rate, but results in an increase in the particulate matter which is caused to deposit and fouling problem of the EGR system. This problem has become an important issue for maintaining the performance of the engine, as well as emission performance. This study had examined the effects of cooler aging on the performance of heat transfer efficiency and NOx emission in non-road diesel engine. As a result of the EGR cooler aging during 200 hours engine operation, the cooling performance decreased about 25% compared with that of fresh cooler and the NOx emission increased about 14.6% on NRSC(non-road steady cycle) and 20% on NRTC(non-road transient cycle) compared with that of fresh cooler respectively.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.3
• /
• pp.341-351
• /
• 2015

When rainfall occurred on road tunnel, that is likely to have influence upon ventilation force in the tunnels but the tunnels ventilation system did not consider factors of rainfall. Thus, this study investigated effects of rainfall upon ventilation force in the tunnels at no rainfall and changing of rainfall by 3 dimensional numerical method. Flow rate into road tunnels decreased as many as 52.34% at rainfall of 150 mm/hr, and pressure drop of road tunnel between entrance and exit decreased as many as 22.22%, so that rainfall had influence upon ventilation force in the tunnel. The number of necessary jet fan in road tunnels is 12 at no rainfall but, when rainfall of 80 mm/hr on road tunnels, the number of necessary jet fan in road tunnels is 16, when rainfall of 150 mm/hr on road tunnels, the number of necessary jet fan in road tunnels is 17. So, factor of rainfall should be considered at estimation of ventilation system of road tunnel.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.15 no.3
• /
• pp.77-81
• /
• 2009

There has been an increasing demand on measurement of the vibration levels in commercial truck shipments, where all packaged products are exposed to some levels of random vibration and shock. In this study, bear glass bottles loaded at the front, middle, and rear positions of 11 tonne truck bed was shipped from Kwangju to Waegouan. Vertical direction vibration levels were analysed and matching laboratory random vibration test was performed using power spectral density (PSD) profiles derived from truck transit records. Also, the effects of drop hight on glass bottles were evaluated. As expected, the maximum vibration levels were recorded at the rear of truck bed. No breakage of bottles were observed during truck transit and laboratory random vibration testing set at 0.52 $G_{rms}$. In drop test, glass bottles were not damaged by bottom side impact, while short side drop impact caused about twice higher bottle breakage rate than that of long side drop impact at 30 cm and 40 cm drop hight.

• Journal of Korean Society of Forest Science
• /
• v.108 no.3
• /
• pp.322-328
• /
• 2019

The purpose of this study was to provide basic data for maintenance and repair of the forest road surfaces using the light drop weight test (LDWT), density test, and grain size analysis at four sites in Yeongyang-gun Mt. (2011y, 2014y, 2016y, and 2017y). In terms of the density test results, the opening density in 2011 was the highest at $2.0694g/cm^3$, and the opening density in 2017 was the lowest at $1.7443g/cm^3$. The grain size analysis showed that the proportion of large aggregates was highest at the opening in 2017, and the proportion of large aggregates decreased with the delay of opening date. From the LDWT results, $E_{vd}$ (the dynamic deformation coefficient) of the 2011y forest road was $35.7MN/m^2$, 2014y was $30.5MN/m^2$, 2016y was $28.6MN/m^2$, and 2017y was $23.5MN/m^2$. The $E_{vd}$ value for the oldest forests opened with the 2011y forest road was the highest, the average $E_{vd}$ value of the center portion was $21.45MN/m^2$, the average $E_{vd}$ value of the wheel portion of the banking part was $31.31MN/m^2$, and the average $E_{vd}$ value of the wheel portion of the cut part was $36.71MN/m^2$.

• Journal of Korean Society of Transportation
• /
• v.23 no.5 s.83
• /
• pp.73-81
• /
• 2005

Triangle-shaped island was been used for the exclusive separation between the right-turn and the through flow. However, in case that existing Triangle-Shaped Island is built at the intersection of narrow road. there are more possibilities of traffic collision trespassing into the opposite lane. Accordingly, separation of the opposite lane is required so as to prevent the intrusion of the large-sized (a heavy) vehicle into the opposite lane turning at the intersection. This study showed the comparison between intersection composed of existing Triangle-Shaped Island and the intersection with Drop Island is added. First of all, in the safety aspect, a method to decide location and shape of Drop Island considering turning trajectory of the large-sized (the heavy vehicle) is addressed. The guideline on the placement of drop island install location and method to decide form the consider heavy truck's turn trajectory in safety side. As a conclusion. we analyzed that drop island is relatively superior to existing Triangle-Shaped Island in terms of driver, ease of driving, driving pleasantness, pedestrian, widening and economic performance aspect.

• International Journal of Highway Engineering
• /
• v.17 no.4
• /
• pp.33-40
• /
• 2015

PURPOSES: Evaluation of the wind speed effect on the temperature drop of an asphalt mixture during construction, by using the transient heat transfer theory and dominant convective heat transfer coefficient model. METHODS: Finite difference method (FDM) is used to solve the transient heat transfer difference equation numerically for various wind speeds and initial temperature conditions. The Blasius convective heat transfer coefficient model is adapted to account for the effect of wind speed in the temperature predictions of the asphalt mixture, and the Beaufort number is used to select a reasonable wind speed for the analysis. As a function of time and depth, the temperature of the pavement structure is predicted and analyzed for the given initial conditions. RESULTS : The effect of wind speed on the temperature drop of asphalt mixture is found to be significant. It seems that wind speed is another parameter to be accounted for in the construction specifications for obtaining a better quality of the asphalt mixture. CONCLUSIONS: It is concluded that wind speed has a significant effect on the temperature drop of the asphalt layer. Although additional field observations have to be made to reflect the effect of wind speed on the construction specifications, it appears that wind speed is a dominant variable to be considered, in addition to the atmospheric temperature.