• Journal of Korean Society on Water Environment
• /
• v.29 no.6
• /
• pp.799-807
• /
• 2013

Reservoir sedimentation is one of the major concerns for sustainable reservoir operation. Since sediment concentration of the rivers in the Himalayan Mountain is very high, a proper sediment management scheme is necessary. This paper presents long-term reservoir sedimentation and sediment flushing based on the gate operation. Focused on the reservoir to be constructed for the Patrind hydropower project in Pakistan, 4 different flushing scenarios were proposed in this study to prevent successive sedimentation. By extending flushing period and by increasing the flushing discharge for 2 times, the flushing rate increases up to 53.2% and 43.6% in proportion to flushing period and discharge, respectively. Based on the simulation presented in this paper, it is expected to establish efficient sediment management plan to increase hydro power generation and sediment flushing simultaneously.

• Smart Structures and Systems
• /
• v.26 no.6
• /
• pp.781-796
• /
• 2020

Prediction of total sediment load is essential in an extensive range of problems such as the design of the dead volume of dams, design of stable channels, sediment transport in the rivers, calculation of bridge piers degradation, prediction of sand and gravel mining effects on river-bed equilibrium, determination of the environmental impacts and dredging necessities. This paper is aimed to investigate and predict the total sediment load of the Wadi Arbaat in Eastern Sudan. The study was estimated the sediment load by separate total sediment load into bedload and Suspended Load (SL), independently. Although the sediment records are not sufficient to construct the discharge-sediment yield relationship and Sediment Rating Curve (SRC), the total sediment loads were predicted based on the discharge and Suspended Sediment Concentration (SSC). The turbidity data NTU in water quality has been used for prediction of the SSC in the estimation of suspended Sediment Yield (SY) transport of Wadi Arbaat. The sediment curves can be used for the estimation of the suspended SYs from the watershed area. The amount of information available for Khor Arbaat case study on sediment is poor data. However, the total sediment load is essential for the optimal control of the sediment transport on Khor Arbaat sediment and the protection of the dams on the upper gate area. The results show that the proposed model is found to be considered adequate to predict the total sediment load.

• Journal of the Korean Geographical Society
• /
• v.43 no.6
• /
• pp.808-823
• /
• 2008

Sediment abrasion in rivers is caused by the interaction between bedrock channel bed and sediment particles transported through the river. Abrasion rate of sediment particles in rivers is controlled by two major factors; Sediment transport conditions including hydraulic conditions form the erosive forces and physical and chemical strengths of the particles form a resistance force against abrasion and other erosional processes. Physical experiments were performed to find the role of each variable on sediment abrasion process. Total 266 sediment particles were used in this experiment. All sediment particles were divided into 11 independent sediment groups with sediment particle size and sediment loads. Each sediment groups were abraded in tumbling mill for up to 8 hours. Changes in weight were recorded by run and total: 2,128 cases of abrasion rate were recoded. Physical strength of rock particles was measured with point load strength index. It is found that sediment abrasion rate has a negative functional relationship point load strength index ($I_{a(50)}$) ($R^2=0.22$). It was suggested that physical strength of sediment particles set the "maximum possible abrasion rate'. As sediment flux increases, abrasion rates of sediment particles with similar point load strength index were changed. It could be concluded that not only physical characteristics of sediment particles, but also sediment transport conditions control sediment abrasion rates.

• Water Engineering Research
• /
• v.1 no.2
• /
• pp.95-105
• /
• 2000

A method is presented which enables easily the computation of the suspended sediment discharge as the mean sediment concentration and mean flow velocity. This method has significant advantages over the traditional method, which principally depend on a set of measured concentration data. The method is based on both a new sediment concentration and mean sediment concentration equations which have been derived from the entropy concept used in statistical mechanics and information theory: (1) The sediment concentration distribution equations derived, are capable of describing the variation of the concentration in the vertical direction. (2) The mean concentration equation derived, is capable of calculating easily the mean concentration by using only one measured concentration in open channel. The present study mainly addresses the following two subjects : (1) new sediment concentration and mean sediment concentration equations are derived from the entropy concept : (2) An efficient and useful method of suspended sediment-discharge measurements is developed which can facilitate the estimation of suspended sediment-discharge in open channel. Flume and laboratory data are used to carry out the research task outlined above. An efficient method for determining the suspended sediment-discharge in the open channel has been developed. The method presented also is efficient and applicable in estimating the sediment transport in rivers and the sediment deposit in the reservoirs, and can drastically reduce the time and cost of sediment measurements.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.5
• /
• pp.21-27
• /
• 2008

The Sediment deposits in rivers and reservoirs are major components interfering with the useful function of the reservoirs, and clogging the inlet port at water intakes in rivers and erosion of pump impellers. Therefore, an accurate estimation method of sediment deposition is requisite to the efficient water resources investigation, planning and management. The objective of this paper is to forecast of reservoir sediment deposition using two dimensional model (SMS) to UnMun reservoir in GyeongSangBukDo. The RUSLE model showed that reservoirs volume was decreased $2,084.09{\times}10^6m^3$ after 50 years and $2,196.65{\times}10^6m^3$ after 100 years, which is plan flood level elevation (EL.152.12 m) reservoir. The two dimensional model showed that reservoirs volume was decreased $2,227.41{\times}10^6m^3$ after 50 years and $2,121.47{\times}10^6m^3$ after 100 years, which is plan flood level elevation (EL.152.12 m) reservoir. The results of this application showed that the use of two dimensional model was very effective for the estimation sediment deposits throughout the reservoir.

• Journal of Environmental Impact Assessment
• /
• v.19 no.5
• /
• pp.497-510
• /
• 2010

Considering to the geochemical behaviors and environmental changes of bottom sediments in streams, Gwangju metropolitan city, this study focuses to analyses on grain sizes, metal elements and organic carbons in sediment samples from Yeongsan and Hwangryong rivers, and Gwangju stream. In the sediments, contents of Cu, Zn, Pb, P and TOC were highly variable, in the case of Gwangju stream particularly. Yenogsan and Hwangryong rivers are influenced by grain sizes and surrounding geological settings and Gwangju stream is connected to organic matters related to life fouls and so forth, with respect to the geochemical behaviorof bottom sediments. Li, Zn, Pb and Cu were enriched in Yeongsan and Hwangryong rivers and Li, Cu, Zn, Pb and P enriched in Gwangju stream, respectively. In the heavy metal contamination of above drainages, the site mutually connected Seobang(GJ 4) with Donggye(GJ 7) streams shows the highest values, in peculiar. It is inferred that those contamination values are mainly related with urban foul waters in the city.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.10 no.2
• /
• pp.112-121
• /
• 2007

In occasion of soil loss happened in a basin, soil in the near of a stream may flow into the stream easily, but in case that soil is far away from the stream, sediment yield transferred to rivers by rainfall diminishes. To forecast sediment yield of a stream is an essential item for management of basins and streams. Therefore, sediment yield of soil loss produced from a basin is needed to be calculated as accurate as possible. Purpose of the present research is to calculate soil erosion amount in a basin and to forecast sediment yield flowed into a stream by rainfall and analyze sediment yield in the stream. There are various methods that analyze sediment yield of rivers. In the present study, the soil erosion amount was calculated using Revised Universal Soil Loss Equation(RUSLE) and GRID, and sediment yield was calculated using sediment delivery ratio and empirical methods. DEM data, slope of basin, soil map and landuse constructed by GIS were used for input data of RUSLE. The upstream area of the Yeongsan river basin in Gwangju metropolitan city was selected for the study area. Three methods according to the calculation of LS factor were applied to estimate the soil erosion amount. Two sediment delivery ratio methods for the respective methods were applied and, correspondingly, six occasions in sediment yield were calculated. In addition, the above results were compared by relative amount with estimation by the empirical method of Ministry of Construction & Transportation. Sediment yield calculated in the present study may be utilized for the plan, design and management of dams and channels, and evaluation of disaster impact.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09a
• /
• pp.371-372
• /
• 2005

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09a
• /
• pp.576-578
• /
• 2005

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.22 no.4
• /
• pp.96-107
• /
• 1980

This study is carried out to estimate the rate of sediment transportation both to measure the amount of suspended and bedload sediment that moves on or near the river bed and passes through the cross section of a river in unit time, with suspended and bed load samplers used for the Milyang river and to determine the most satisfactory and convenient formula of some formulas for sediment discharge by comparing the measured rate with the calculated rate. The results of this study are summarized as follows; 1) The interrelationship (1) between the total discharge and the total sediment discharge (2) between discharge and suspended sediment load and (3) between discharge and bed load in the Milyang river are (1) i) 4$\leq$Q$\leq$100 C.M.S. Qr=0. 00272 Q0.70 (kg/sec) ii) 150$\leq$Q$\leq$800 C.M.S. Qr=0. 4807 Q0.46 (kg/sec) (2) Qs~=0. 07576 Q1.02 (kg/sec) (3) QB=0. 00957 Q0.44 (kg/sec) 2) The rate of suspended sediment load to total sediment discharge is found to be about; 99%. The suspended load is shown to be almost wash load which consists of silt and clay. 3) The relation between the total discharge and the suspended sediment load that are measured at three medium and small rivers in Korea is Qs=0. 13831 Q0.97 (kg/sec) 4) Brown's formula is determined to be the most convenient formula for application and comparison with observed data obtained for the Milyang river.