• 한국전기전자재료학회논문지
• /
• 제15권9호
• /
• pp.798-807
• /
• 2002

ZnO thin films on Si wafer were deposited by RF magnetron reactive sputter with various RF power, chamber pressure, argon/oxygen gas ratios ana substrate temperatures. Crystallinities, surface morphologies, and electrical properties of the films were investigated by XRD, AFM, RBS, and electrometer(keithley 617). ZnO films showed a strong c-axis preferred orientation. Surface roughness and resistivity were changed by the argon/oxygen gas ratio. The minimum surface roughness of 12${\AA}$ and maximum resistivity of $10^8\Omega cm$ were achieved at Ar/O$O_2$=0/100.

• 한국전기전자재료학회논문지
• /
• 제27권12호
• /
• pp.815-819
• /
• 2014

Aluminum nitride (AlN) thin film and TiN film as a buffer layer were deposited on INCONEL 600 substrate by reactive RF magnetron sputtering at room temperature(R.T.) under 25~75% $N_2/Ar$ atmosphere. The as-deposited AlN films at 25~50% $N_2/Ar$ showed a polycrystalline phase of hexagonal AlN, and an amorphous phase. The peak of AlN (002) plane, which was determinant on a performance of piezoelectric transducer, became strong with increasing the $N_2/Ar$ ratio. Any change in the preferential orientation of the as-deposited AlN films was not observed within our $N_2$ concentration range. The piezoelectric sensing properties of AlN module were performed using pressure-voltage measurement system. The output signal voltage of AlN module showed a linear behavior between 20~80 mV in 1~10 MPa range, and the pressure-sensing sensitivity was calculated as 3.6 mV/MPa.

• 한국결정성장학회지
• /
• 제21권2호
• /
• pp.65-69
• /
• 2011

RF 마그네트론 스퍼터링으로 가스조성비와 기판의 온도를 변화시키면서 $Tio_2$ 박막을 성장하였다. XRD, SEM, AFM 및 분광 광도계를 이용하여 박막의 구조와 광학적 특성을 고찰하였다. 박막에는 아나타제 결정성만 관찰되었으며 온도가 높아질수록 회절 피크의 강도가 증가하였다. 산소농도가 증가함에 따라 기둥구조의 결정성장률이 감소되었으며 굴절률과 흡수율은 감소하였다. $Tio_2$ 박막은 300~400oC의 기판온도와 10 %의 $O_2$ 분위기에서 성장한 박막의 표면이 매끄럽고 투과특성이 우수한 $300{\sim}400^{\circ}C$ 박막을 얻을 수 있었다.

• 한국진공학회지
• /
• 제7권3호
• /
• pp.201-207
• /
• 1998

본 연구는 rf reactive magnetron sputtering 방법으로 증착한 ZnO 박막을 압전진동 자로 제작하였을 때 발생하는 금속전극과의 계면특성에 대해 조사하였다. 이때 ZnO 박막은 금속 아연 target을 산소분위기에서 sputtering하여 얻었다. 미리 얻은 최적성장조건으로 Cr/ZnO/Cr의 구조을 갖는 압전 진동자를 제작한 후, 금속전극과 ZnO 박막과의 계면특성을 분석하였다. 제작된 압전진동자는 I-V 측정, AES depth profile, SEM, C-V 측정등을 이용 하여 분석하였고, 이러한 분석 결과 금속전극과 ZnO 박막 사이에 $SiO_2$ 확산방지막을 쌓은 Cr/ $SiO_2$/ZnO/Cr의 구조로 ZnO 압전진동자를 제작했을 때 좋은 특성을 보임을 알 수 있었 다. 그리고, 이러한 사실은 제작된 진동자를 구동시키고 이에 대한 인가진동수에 따른 진동 변위를 측정해보므로써 확인할 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.211-211
• /
• 2012

The electrical loss of the photo-generated carriers is dominated by the recombination at the metal- semiconductor interface. In order to enhance the performance of the solar cells, many studies have been performed on the surface treatment with passivation layer like SiN, SiO2, Al2O3, and a-Si:H. In this work, Al2O3 thin films were investigated to reduce recombination at surface. The Al2O3 thin films have two advantages, such as good passivation properties and back surface field (BSF) effect at rear surface. It is usually deposited by atomic layer deposition (ALD) technique. However, ALD process is a very expensive process and it has rather low deposition rate. In this study, the ICP-assisted reactive magnetron sputtering method was used to deposit Al2O3 thin films. For optimization of the properties of the Al2O3 thin film, various fabrication conditions were controlled, such as ICP RF power, substrate bias voltage and deposition temperature, and argon to oxygen ratio. Chemical states and atomic concentration ratio were analyzed by x-ray photoelectron spectroscopy (XPS). In order to investigate the electrical properties, Al/(Al2O3 or SiO2,/Al2O3)/Si (MIS) devices were fabricated and characterized using the C-V measurement technique (HP 4284A). The detailed characteristics of the Al2O3 passivation thin films manufactured by ICP-assisted reactive magnetron sputtering technique will be shown and discussed.

• The Korean Journal of Ceramics
• /
• 제3권4호
• /
• pp.257-262
• /
• 1997

Aluminum nitride(AIN) thin films were deposited on SiO$_2$/Si substrates by reactive sputtering for the application of SAW devices. The major deposition parameters such as pressure, nitrogen fraction, rf power, substrate distance were changed to find out the optimal condition for c-axis oriented thin films on an amorphous substrate. The effects of deposition parameters on the crystal structure, residual stress, and growth morphology of thin films were characterized by XRD, SEM, and TEM. The FWHM of (002) rocking curve of the films deposited at the proper condition was lower than 2.2$^{\circ}$(C=0.93$^{\circ}$). Cross-sectional TEM showed that self-aligned structure was developed just after slightly random growth at the initial stage. The frequency characteristics of test device fabricated from AIN thin films confirmed their piezoelectric property and applicability for SAW devices.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권7호
• /
• pp.288-292
• /
• 2003

AlM thin film has been deposited on A1$_2$O$_3$ substrate by reactive radio frequency(RF) magnetron sputtering method under various operating conditions such as working pressure, fraction of nitrogen partial pressure, and substrate temperature. Scanning Electron Microscope(SEM), X-ray Diffraction(XRD), and Atomic Force Microscope(AFM) have been measured to find out structural properties and preferred orientation of AlN thin films. SAW velocity of IDTs/AlN/Si structure was about 5038［㎧］ at the center frequency of 251.9［MHz］ and insertion loss was measured to be relatively low value of 35.6［dB］. SAW velocity of IDTs/AlN/A1$_2$O$_3$ structure was improved to be about 5960［㎧］ at the center frequency of 296.7［MHz］.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.292-292
• /
• 2013

최근, 자연의 기능성 표면을 모사하여 우리 생활에 응용하기 위한 연구가 활발하다. 초-발수 특성을 가지는 대표적인 예인 연꽃잎은 마이크로-나노 크기의 거친 미세돌기(papillae)를 가지고 있으며 그 위에 낮은 표면 에너지를 가지는 왁스(wax)가 발달 되어 항상 깨끗한 상태를 유지한다. 본 실험에서는 이를 모사하여 RIE (Reactive Ion Etching)방법을 이용하여 기판인 Poly silicon wafer를 Sf6가스를 사용하여 Metal mash로 거칠기를 만들어 주었고, RF-magnetron sputtering 장치를 사용하여 $6{\times}10^{-3}$ Torr의 진공도에서 낮은 표면에너지를 가지는 PTFE (polytetrafluoroethylene)를 증착하여 표면 구조와 발수특성에 대하여 조사하였다. SSME(Surface shape measurement equipment)측정결과 0.24~0.36 um RSa 값이 측정되었고, 12 uL의 Di-water로 접촉각을 측정 한 결과 RIE 10분 처리를 한 기판 위에 PTFE를 3분 증착하였을 때 가장 높은 $153^{\circ}$의 초-발수 특성이 나타났으며, 4주의 시간이 지났을 때에도 접촉각이 유지가 되었다. XPS 측정결과 초-발수 표면에서 나타나는 CF2와 CF3 피크 값이 측정되었다. Reactive Ion Etching을 이용한 PTFE 발수 특성은 방수, 스마트 윈도우, 자가세정(Self-Cleaning), 디스플레이 표시장치, 김서림 방지(Anti-Fogging), 대전방지 코팅 등에 다각적으로 응용 가능할 것이라 사료된다.

• 한국태양에너지학회 논문집
• /
• 제26권4호
• /
• pp.55-61
• /
• 2006

Titanium oxide ($TiO_2$) films are deposited on the indium tin oxide (ITO) substrate in an $Ar/O_2$ atmosphere by using reactive RF (Radio Frequency) magnetron sputtering technique, and Electrochromic properties and durability of $TiO_2$ films deposited at different preparation conditions are investigated by using UV-VIS spectrophotometer and cyclic voltammetry Li+ interalation/deintercalation in $TiO_2$ films shows that the electrochromic properties and durability of as-deposited films strongly depend on gas pressure $TiO_2$ films formed in our sputtering conditions are found to remain transparent, irrespective of their Li+ ion contents. The optimum sputtering conditions for film as passive counter electrode in electrochromic devices are working pressure of $1.0\;{\times}\;10^{-2}\;torr$ and oxygen flow raes of $10{\sim}15\;sccm$, respectively.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.306.2-306.2
• /
• 2016

Niobium oxide thin films were synthesized by reactive rf magnetron sputtering. The target was metallic niobium with 2 inch in diameter and the substrate was n-type Si wafer. To control the surface properties of the films, Nb oxide thin films were obtained at various mixing ratios of argon and oxygen gases. Nb oxide thin films were analyzed with alpha step, scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The result of alpha step showed that the thickness of Nb oxide thin films were decreased with increasing the oxygen gas ratios. SEM images showed that the granular morphology was formed at 0% of oxygen gas ratio and then disappeared at 20 and 75% of oxygen gas ratio. The amorphous Nb oxide was observed by XRD at all films. The oxidation state of Nb and O were studied with high resolution Ni 2p and O 1s XPS spectra. And the change in the chemical environment of Nb oxide thin films was investigated by XPS with Ar+ sputtering.