• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.11
• /
• pp.2397-2402
• /
• 2010

Dielectric resonator bandpass filters with various time-delay at 800MHz were designed and fabricated in this paper. from the results of this study. first of all, good response. characteristics were measured for all cases. The insertion loss was below 2dB and flatness for ripple was below 0.2dB, whereas return loss was over 20dB, respectively. The measured delay time of the fabricated prototype were 6ns, 12ns and 200s, respectively and the flatness characteristics did not exceeding Ins for all cases. Furthermore, 2~4ns of flatness were measured for 2-hole dielectric block and other dielectric resonator filters with various delay time by combination of each prototypes filters were also implemented.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.1
• /
• pp.11-19
• /
• 2010

The performance of the crossover system of a centrifugal compressor stage consisting of static components of $180^{\circ}$ U-bend, return channel vanes and exit ducting with a $90^{\circ}$ bend is investigated. This study is confined to the assessment of performance of the crossover system by varying the shape of the return channel vanes. For this purpose two different types of Return Channel Vanes (RCV1 and RCV2) were experimentally investigated. The performance of the crossover system is discussed in terms of total pressure loss coefficient, static pressure recovery coefficient and vane surface pressure distribution. The experimentation was carried out on a test setup in which static swirl vanes were used to simulate the flow at the exit of an actual centrifugal compressor impeller with a design flow coefficient of 0.053. The swirl vanes are connected to a mechanism with which the flow angle at the inlet of U-bend could be altered. The measurements were taken at five different operating conditions varying from 70% to 120% of design flow rate. On an overall assessment RCV1 is found to give better performance in comparison to RCV2 for different U-bend inlet flow angles. The performance of RCV2 was verified using numerical studies with the help of a CFD Code. Three dimensional sector models were used for simulating the flow through the crossover system. The turbulence was predicted with standard k-$\varepsilon$, 2-equation model. The iso-Mach contour plots on different planes and development of secondary flows were visualized through this study.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.259-269
• /
• 2013

In this paper, we propose an SIW(Substrate Integrated Waveguide) multi-section E-plane transformer using air-holes for an SIW system with variable thicknesses. Air-holes are inserted into a SIW E-plane quarter wavelength transformer for matching an E-plane impedance discontinuity. A PSIW(Punched Substrate Integrated Waveguide) consisted of air-holes has an SIW characteristic impedance tunability because of reducing a equivalent shunt capacitance of the SIW. And, a PSIW multi-section E-plane transformer is implemented for improving a matching bandwidth by using the Chebyshev polynomial. The measurement results of PSIW double-section E-plane transformer show that the insertion loss($S_{21}$) is $1.57{\pm}0.11$ dB and input return loss($S_{11}$) is more than 15 dB from 11.45 GHz to 13.6 GHz.

• ETRI Journal
• /
• v.26 no.6
• /
• pp.589-596
• /
• 2004

Packaging technologies for a broadband and narrowband modulator with a traveling wave electro-absorption modulator (TWEAM) device were developed. In developing a broadband modulator, the effects of the device and packaging designs on the broadband performance were investigated. The optimized designs were obtained through a simulation with the result that we developed a broadband modulator with a 3 dB bandwidth of 38 GHz in the electrical-to-optical (E/O) response, an electrical return loss of less than -10 dB at up to 26 GHz, an rms jitter of 1.832 ps, and an extinction ratio of 5.38 dB in a 40 Gbps non-return to zero (NRZ) eye diagram. For analog application, the effect of the RF termination scheme on the fractional bandwidth was studied. The microstrip line with a double stub as a matching circuit and a laser trimming process were used to obtain an $S_{11}$ of -34.58 dB at 40 GHz and 2.9 GHz bandwidth of less than -15 dB.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.112-116
• /
• 2005

This paper presents a broadband two-stage low noise amplifier(LNA) operating from 3 to 10 GHz, designed with 0.18 ${\mu}m$ RF CMOS technology, The cascode feedback topology and broadband matching technique are used to achieve broadband performance and input/output matching characteristics. The proposed UWB LNA results in the low noise figure(NF) of 3.4 dB, input/output return loss($S_{11}/S_{22}$) of lower than -10 dB, and power gain of 14.5 dB with gain flatness of $\pm$1 -dB within the required bandwidth. The input-referred third-order intercept point($IIP_3$) and the input-referred 1-dB compression point($P_{ldB}$) are -7 dBm and -17 dBm, respectively.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.61-64
• /
• 2002

We have optimally designed and implemented by a monolithic microwave integrated circuit(MMIC) the low noise amplifier(LNA) of 5.8GHz band composed of receiver front-end(RFE) in a on-board equipment system for dedicated short range communication using a depletion-mode GaAs MESFET. The LNA is provided with two active devices, matching circuits, and two drain bias circuits. Operating at a single supply of 3V and a consumption current of 18㎃, The gain at center frequency 5.8GHz is 13.4dB, Noise figure(NF) is 1.94dB, Input 3rd order intercept point(lIPS) is 3dBm, and Input return loss(5$_{11}$) and Output return loss(S$_{22}$) is -l8dB and -13.3dB, respectively. The circuit size is 1.2$\times$O.7$\textrm{mm}^2$.EX>.>.

• Journal of electromagnetic engineering and science
• /
• v.19 no.1
• /
• pp.64-70
• /
• 2019

In this study, a compact series-fed center-fed open-stub (SFCFOS) linear array antenna for K-band applications is presented. The antenna is composed of a single-line 10-element linear array. A symmetrical Chebyshev amplitude distribution (CAD) is used to obtain a low sidelobe characteristic against a uniform amplitude distribution (UAD). The amplitude is controlled by varying the width of the microstrip patch elements, and open-ended stubs are arranged next to the last antenna element to use the energy of the radiating signal more effectively. We insert a series-fed stub between two patches and obtain a low mutual coupling for a 4.28-mm center-to-center spacing ($0.7{\lambda}$ at 21 GHz). A prototype of the antenna is fabricated and tested. The overall size of the uniform linear array is $7.04{\times}1.05{\times}0.0563{\lambda}_g^3$ and that of the Chebyshev linear array is $9.92{\times}1.48{\times}0.0793{\lambda}_g^3$. The UAD array yields a ${\mid}S_{11}{\mid}$ < -10 dB bandwidth of 1.33% (20.912-21.192 GHz) and 1.45% (20.89-21.196 GHz) for the CAD. The uniform array design gives a -23 dB return loss, and the Chebyshev array achieves a -30.68 dB return loss at the center frequency with gains of 15.3 dBi and 17 dBi, respectively. The simulated and measured results are in good agreement.

• Journal of Broadcast Engineering
• /
• v.16 no.3
• /
• pp.483-489
• /
• 2011

In this paper, we propose a new antenna, which has wide bandwidth, good radiation patterns, and high-gain characteristics. We analysis the antenna using FDTD(Finite Difference Time Domain) method. And the antenna parameters are optimized to get maximum bandwidth. From the measured results, the bandwidth of the antenna is 0.839 octave, for the S11${\leq}$-10 dB. And the measured cross polarization level of the proposed antenna is less than -25 dB at the center frequency. Experimental data of the return loss and the radiation pattern of the proposed antenna are also presented, and the experimental bandwidth characteristics are relatively in good agreement with the FDTD results. The proposed antenna can be applied to MIMO, LAN, biomedical instruments, broadcasting-network system.

• Korean Institute of Interior Design Journal
• /
• v.13 no.3
• /
• pp.11-16
• /
• 2004

Adolf Loos studied at the Dresden Institute of Technology. He lived in America from 1893 to 1896. On his return to Vienna, hi worked for a year with the architect, Carl Mayreder. From 1897, he wrote extensively on design and architectural matters. In 1908, his famous article "Ornament and Crime"(Ornament und Verbrechen) was published, in which he linked the use of excessive decoration to a debasement of society. For Adolf Loos, it was a question not of renunciation of every ornament, but of the liberation from superfluous ornament. Where ornament was pastes on only, without connection with the subject or the building, and where ornament was not honest with the hand put on, the ornament is supposed to be removed. Onto the place of the ornament the joy of the material and the shaping should step. That the opinion of Adolf Loss is not correctly understood Is due on the one hand to the concentration on the 'ornament and crime' too very much. On the other hand his extreme Position is supposed to be understood more as thinking-impulse, more as provocation.ovocation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.441-444
• /
• 2007

In this paper, the resonance characteristics of ZnO-based film bulk acoustic resonator (FBAR) devices with high-quality multi-layer reflectors are proposed. The ultrathin Cr film $(300\;\AA-thick)$ between $SiO_2$ film and W film is formed by a sputtering-deposition in order to enhance the adherence at their interfaces. The resonance frequency was observed to vary with the number of the reflectors. This seems to be attributed to the change in the effective thickness of the ZnO film. Also, increasing the number of layers has led to a significant improvement of the series/parallel quality factor.