• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.890-896
• /
• 2004

This study is intended as an investigation of the EK remediation characteristics of natural soil with treatment time under unsaturated conditions. EK tests are performed under the voltage gradient of 1V/cm, the degree of saturation of 82.8%, and the installing of cation exchange membrane. It was found from the results that the acid front is initially transported at 0.75cm/day and then continuously degreased until the transport velocity of the acid front is balanced to the velocity of the base front. The residual lead concentration indicated the maximum value at the treatment time of lOdays, then the increasing of treatment time largely decreases the concentration within the sample though electromigration than electroosmosis.

• Proceedings of the KIEE Conference
• /
• 2009.04a
• /
• pp.77-79
• /
• 2009

Nonlinear system fault detection and isolation of this paper is about the failure of unknown function approximation using neural network for fault detection and isolation techniques of induction motors were applied. observer-based fault signal residual value was used. Induction motor using the speed controller of the backstepping controller. Proposed fault detection and isolation to prove the performance of the simulation was applied to and the actual system.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.57.2-57
• /
• 2001

Timed token protocols inadequately provide periodic communication service, although this is crucial for hard real time systems. We propose an approach to guaranteeing periodic communication service on a timed token protocol network. In this approach, we allocate bandwidth to each node so that the summation of bandwidth allocations is Target Token Rotation Time (TTRT). If a node cannot consume the allocated time, the residual time can be used by other nodes for non-periodic service using a timer which contains the unused time value and is appended to the token. This approach can always guarantee transmission of real-time messages before their deadlines when the network utilization is less than 50%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.82-85
• /
• 2003

The sapphire wafers for blue light emitting devices were manufactured by the implementation of the surface machining technology based on micro-tribology. This process has been performed by Micro-lapping process. The sapphire crystalline wafers were characterized by DCXD(Double Crystal X-ray Diffraction). The sample quality of crystalline sapphire wafer at surface has a FWHM(Full Width at Half Maximum) of 250 arcsec. This value at the sapphire wafer surfaces indicated 0.12${\mu}{\textrm}{m}$ sizes. Surfaces of sapphire wafers were mechanically affected by residual stress and surface default. Also Surfaces roughness of sapphire wafers were measured 2.1 by AFM(Atom Force Microscope).

• International Journal of Precision Engineering and Manufacturing
• /
• v.1 no.2
• /
• pp.105-114
• /
• 2000

An output feedback control (OFC) is presented for a linear stochastic system with known disturbance and applied to a flexible spacecraft for the reduction of residual vibration while allowing the natural deflection during operation. By converting the tracking problem into regulator problem, the OFC minimizes the expected value of a guadratic objective function composing of error stats which always remain on the intersection of sliding hypersurfaces. For the numerical evaluation with a flexible spacecraft, a large slewing maneuver strategy is devised with a tracking model for nominal trajectory and start-cost-stop strategy for economical maneuver in conjunction with the input shaping technique. The performance and efficacy of the proposed control scheme are illustrated with the comparison of different maneuver strategies.

• Rapid Communication in Photoscience
• /
• v.2 no.1
• /
• pp.34-37
• /
• 2013

Two novel antenna complexes of $Eu^{III}$ with 1-naphthoic acid (NA) as primary ligand and two aromatic N-donor ligands namely N-hexyl-N-(pyridin-2-yl) pyridin-2-amine (1) and 4-((dipyridin-2-ylamino)methyl)benzoic acid (2) have been synthesized and characterized by various spectroscopic techniques. The room-temperature (298 K) photoluminescence spectrum of $Eu^{III}$ complexes composed of typical line like emissions, assigned to transitions between the first excited state $^5D_0$ to the $^7F_J$ (J = 0-4), resulting in red emission along with the residual emission from the 1-naphthoic acid moiety in the blue region. The determined CIE color coordinate value for the complex 2 is (x = 0.36, y = 0.34), which is in white region.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.218-224
• /
• 1999

It is necessary to improve mechanical and optical properties in the optical disk substrates as the information storage devices with high storage density using short wavelength laser are being developed. Injection compression molding is regarded as the most suitable process to manufacture optical disk substrates with high is regarded as the most suitable process to manufacture optical disk substrates with high dimensional accuracy low residual stresses and superb optical properties In the present study polycarbonate optical disk substrates were fabricated by injection compression molding and the birefringence regarded as one of the most important optical properties for optical disk is measured. The effects of various processing conditions upon the development of birefringence distribution were examined experimentally. It was found that the value of the birefringence distribution were very sensitive to the mold wall temperature history and the variance of the birefringence distribution in the radial direction was affected by the level of the packing and the compression pressure.

• Journal of Korean Society of Water and Wastewater
• /
• v.13 no.2
• /
• pp.23-33
• /
• 1999

This study is to investigate the effect of C factor errors on the analysis of water distribution systems. For this purpose, an artificial distribution network and a real distribution network were selected as the study networks. Results are as follows. 1. The C factor of a pipe which has small velocity didn't give significant effect on the analysis of a water distribution system. 2. The effect of decreased value of C factors give more influence on the analysis of water distribution systems than that of the increased values. 3. For the C factor calibration, errors of the residual water heads as well as those of the head losses should be considered together. 4. In the analysis of water distribution systems, changes of C factors can give influences only on the nodes which locate behind the pipe. Therefore, this characteristics should be considered in the selection of nodes for the measurement of water heads.

• Journal of the Korean Ceramic Society
• /
• v.13 no.1
• /
• pp.20-24
• /
• 1976

These are many kinds of self-hardening methods for sand mold using sodium silicate. When sodium silicate solution is mixed with calcium-orthosilicate powder hardening reaction occurs, which is based for self-hardening method at high temperature. The high temperature strength and resicual strength of mold are related to the mole ratio of sodium silicate and the contents of calcium-orthosilicate powder. The results obtained in this study were as follows: 1) The high temperature strength of mold was maximum at about $600^{\circ}C$, and at higher temperature showed lower value on the contrary. 2) The high temperature strength of mold was increased by increasing the amount of sodium silicate having lower mole ratio and high concentration. 3) The residual strength of mold was reduced by increasing the mole ratio of sodium silicate and increasing the concentration of calcium-orthosilicate.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.248-253
• /
• 2000

This paper presents parametric study of long-rod penetration. Influences of yield stress of penetrator and target material on the penetration results such as crater size and penetrator residual length are contemplated. Numerical experiments are carried out with varying the value of static yield stress of materials. Lagrangian explicit code NET2D was used to perform parametric study. Element eroding algorithm was used to properly simulate long-rod penetration. Analytic and empirical model of long-rod penetration and Taylor test are used to explain the relationships of parameter and simulation results.