• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.89-95
• /
• 2000

In order to achieve effective prediction of residual stresses, the series experiment were carried out and the residual stresses were measured using the backgpropagation algorithm from the neural network and the sectional method. Using the experimental results, the optimal control algorithms using a neural network should be developed in order to reduce the effect of the external disturbances on residual stresses during GMA welding processes. The results obtained from the comparison between the measured and calculated results, showed that the neural network based on backpropagation algorithm can be sued in order to control weld quality. This system can not only help to understand the interaction between the process parameters and residual stress, but also, improve the quantity control for welded structures. The development of the system is goal in this study.

• YAKHAK HOEJI
• /
• v.45 no.5
• /
• pp.437-441
• /
• 2001

The quasi-drugs including nonwoven fabric and gauze were sterilized using ethylene oxide (EO) gas. Residual EO in the quasi-drugs was extracted with water (20 mL of water for 1 g of sample) for 24h at 37$^{\circ}C$. Residual EO was determined using GC. The optimal analytical conditions were as follows : column, Carbowax 20M (1.D. 0.2 mm); mobile phase, helium with 30 mL/min; oven temperature 57$^{\circ}C$, injector temperature 18$0^{\circ}C$, detector temperature 20$0^{\circ}C$. The detection limit for EO was 0.10$\mu$g/mL. When the residual EO extracted from nonwoven fabric and gauze was determined, it took more than 9h to get the lower level than 25 ppm which is the limit value of FDA guideline. When the EO residues, ethylene chlorohydrine (ECH) and ethylene glycol (EG) in the 7 commercially available quasi-drugs were determined, no residual EO, ECH, EG were found from the seven commercially available quasi-drugs analyzed by this method.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.305-314
• /
• 1998

This study has been performed to investigate into some effects of various amounts of $CO_2$ and CO gas added to the $50%NH_3-N_2$ based gas atmosphere on microstructure, hardness, chemical analysis and residual stress in the compound and diffusion layer of AISI H13 treated by gaseous nitrocarburising process. The compound layer formed in the surface is composed of mainly ${\varepsilon}-Fe_3$(N,C) and small amount of ${\gamma}^{\prime}-Fe_4N$ and cementite. The maximum hardness value obtainable from H13 steel is shown to be 1200 Hv and the effecvtive hardening depth increases with increasing CO content from 1% to 4%. In the case of CO content over 4%, however, it decreases with increasing CO content. The composition profiles of nitrogen and carbon are found to be within the ${\varepsilon}$-phase field located above the ${\varepsilon}+{\gamma}^{\prime}$ phase field in the Fe-N-C diagram. It is shown that the maximum value of compressive residual stress of H13 steel treated in atmospheres of $50%NH_3-(2,4)%CO_2-N_2-CO$ gas mixture is $48kg/mm^2$ and the depth to which residual stress is in Compressive state is $90{\mu}m$ for the atmosphere $50%NH_3-45%N_2-4%CO_2-1%CO$ gas mixture. It is consequently important to control the maximum value and size of compressive residual stress region in order to obtain desirable mechanical properties.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.8
• /
• pp.4847-4851
• /
• 2013

Objectives: To evaluate accuracy of FDG-PET CT in prediction of persistent disease in head and neck cancer cases and to determine prognostic value of metabolic tumor response. Materials and Methods: Between 2009 and 2011, 46 patients with squamous cell carcinoma of head and neck receiving PET-CT were treated with definitive radiotherapy, with or without chemotherapy. There were 29 nasopharyngeal, 11 hypopharyngeal, 3 oropharyngeal and 3 laryngeal cancer patients, with a median age of 50.5 years (range 16-84), 32 males and 14 females. All patients were evaluated with PET-CT median 3-5 months (2.4-9.4) after completion of radiotherapy. Results: After a median 20 months of follow up, complete metabolic response was observed in 63% of patients. Suspicious residual uptake was present in 10.9% and residual metabolic uptake in 26.0% of patients. The overall sensitivity, specificity, positive predictive value and negative predictive value of FDG-PET-CT for detection of residual disease was 91% and 81%, 64% and 96% respectively. Two year LRC was 95% in complete responders while it was 34% in non-complete responders. Conclusions: FDG PET CT is a valuable tool for assessment of treatment response, especially in patients at high risk of local recurrence, and also as an indicator of prognosis. Definitely more precise criteria are required for assessment of response, there being no clear cut uptake value indicating residual disease. Futhermore, repair processes of normal tissue may consume glucose which appear as increased uptake in control FDG PET CT.

• Korean Journal of Materials Research
• /
• v.33 no.5
• /
• pp.205-213
• /
• 2023

This paper reports the results of an experimental examination using X-rays to test annealing materials for lapped bearing steel (STB2), to confirm the validity of the weighted averaging analysis method. The distribution behavior for the α_𝜓-sin²𝜓 diagram and the presence or absence of differences in the peak method, half-value breadth method, and centroid method were investigated. When lapping the annealed bearing steel (STB2) material, a residual stress state with a non-directional steep gradient appeared in the surface layer, and it was found that the weighted averaging analysis method was effective. If there is a steep stress gradient, the sin²𝜓 diagram is curved and the diffraction intensity distribution curve becomes asymmetric, resulting in a difference between the peak method, half-value breadth method, and centroid method. This phenomenon was evident when the stress gradient was more than 2~3 kg/mm²/㎛. In this case, if the position of the diffraction line is determined using the centroid method and the weighted averaging analysis method is applied, the stress value on the surface and the stress gradient under the surface can be obtained more accurately. When the stress gradient becomes a problem, since the curvature of the sin²𝜓 diagram appears clearly in the region of sin²𝜓 > 0.5, it is necessary to increase the inclination angle 𝜓 as much as possible. In the case of a lapping layer, a more accurate value can be obtained by considering 𝜎₃ in the weighted averaging analysis method. In an isotropic biaxial residual stress state, the presence or absence of 𝜎₃ can be determined as the presence or absence of strain for sin²𝜓≈0.4.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.578-585
• /
• 2004

Hardness test is performed for determination of the other properties, such as strength, wear resistance and deformation resistance, as well as hardness itself. And it is performed for prediction of residual lifetime by analysis of hardness reduction or hardness ratio. However, hardness test has limitation that observation of residual indent is needed for determination of hardness value, and that is the reason for not to be widely used in industrial field. Therefore, in this study, we performed researches to obtain Brinell hardness value from quantitative numerical formula by analysing relationship between indentation depths from indentation load-depth curve and mechanical properties such as work hardening exponent, yield strength and elastic modulus.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.25-30
• /
• 2000

Residual stresses induced in U-bending and tube-to-tubesheet joining processes of PWR's steam generator row-1 tube were measured by X-ray method and Hole-Drilling Method(HDM). The stresses resulting from the Internal pressure and the temperature gradient in the steam generator were also estimated theoretically. In U-bent lesions, the residual stresses at extrados were induced with compressive stress(-), and its maximum value reached -319 MPa in axial direction at ${\psi}=0^{\circ}$ in position. Maximum tensile residual stress of 170MPa was found to be at the flank side at Position of${\psi}=90^{\circ}$, i.e., at apex region. In tube-to-tubesheet fouling methods, the residual stresses induced by the explosive joint method were found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the. transition region, and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction. Hoop stress due to an internal pressure between primary and secondary side was analyzed to be 76 MPa and thermal stress was 45 MPa.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.6
• /
• pp.50-59
• /
• 2022

The design of the substrate significantly affects the thermal history and the residual stress formation in the vicinity of a repaired region by a directed energy deposition (DED) process. The occurrence of defects in the repaired region depends on the thermal history and residual stress formation. The objective of this study was to investigate the influence of the inclined angle and depth of the substrate on the thermal and residual stress characteristics in the vicinity of a repaired region by a DED process through two-dimensional finite element analyses (FEAs). The temperature and residual stress distributions in the vicinity of the repaired region were predicted according to the combination of the inclined angle and depth of the substrate. The effects of the inclined angle and depth on the depth of the heat affected zone and the maximum value of the residual stress were examined. A proper combination of the inclined angle and depth of the substrate was estimated to decrease the residual stress in the vicinity of the repaired region.

• Korean Business Review
• /
• v.11
• /
• pp.195-216
• /
• 1998

Ownership of an asset can be identified with the right to exercise "residual control" where the contract is silent about decision rights, or with the right to receive any "residual returns" that remain after contractual. obligations are fulfilled. Although the concept of "ownership" seems reasonably clear in many of the cases, the concepts of residual control and the residual returns that define ownership are actually quite elusive. For large corporations, there is really no single individual who owns both the residual returns and the residual control. Despite the limited qualifications, ownership is clearly. the most common and effective meas to motivate people to create, maintain, and improve the value of assets. In this paper, we try to clarify the relationships among financial structure, ownership, and corporate control with the concept of ownership defined as the residual control and the residual returns, Financial securities are not just claims to part of a firm's net income. They give the security holder certain rights. A careful matching of rights of control and returns can create incentives that increase total value of the firms. In the corporate firms, managers, lenders, and shareholders have different interests. And the financial structure affects how different those interests are and what decisions management will make. Managers are, in general, better informed than investors about the firm's prospects. The financial decisions by managers may affect investors' beliefs and, therefore, the price of shares and the value of the firm.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.12
• /
• pp.1011-1016
• /
• 2015

In a roll-to-roll continuous system, winding is one of the most important processes since it determines the quality of the final manufactured products such as flexible film and printed electronic devices. Since an adequate winding tension can reduce the incidence of the defects that are derived from the inner stress of the wound roll such as starring and telescoping, it is necessary to determine the optimal taper-tension profile. In this study, an algorithm for the setting of an optimal taper-tension profile in consideration of the residual stress in the wound roll is suggested; furthermore, the algorithm was adjusted for the determination of an optimal taper-tension profile regarding the winding process of $10{\mu}m$ polypropylene (PP) film. As a result of the algorithm-generated, optimal taper-tension profile, the residual stress and radial stress in a PP wound roll were decreased to 27.37 % and 40.05 % (mean value), respectively.