• Journal of the Korean GEO-environmental Society
• /
• v.14 no.11
• /
• pp.13-23
• /
• 2013

In the west coastal soft ground, the static and dynamic loading tests for PHC piles which were executed using light driving without injecting cement milk were carried out and the correlation was analyzed. Initial dynamic loading test used hydraulic hammer(ram weight 70kN) and final average penetration effect presented 3.0 to 8.0mm at 0.8m drop. Then final allowable bearing capacity using CAPWAP presented 776.4 to 1,053.6kN a pile. The static loading tests which were performed at the other piles loaded 200% of the design load dividing by eight phases. As the result, total settlement was 15.97 to 16.38mm and residual settlement was 4.48 to 5.38mm, but both yielding and ultimate load can't be estimated. Therefore, allowable bearing capacity was determined larger than 1,200kN a pile regarding maximum test load as yielding load. Thus, it showed that allowable bearing capacity of the dynamic loading test was larger than static loading test in 1.54 to 1.14 times.

• Journal of Welding and Joining
• /
• v.33 no.5
• /
• pp.53-60
• /
• 2015

Laser surface Melting Process is getting hardening layer that has enough depth of hardening layer as well as no defects by melting surface of substrate. This study used CW(Continuous Wave) Yb:YAG and STD11. Laser beam speed, power and beam interval are fixed at 70mm/sec, 2.8kW and 800um respectively. Hardness in the weld zone are equal to 400Hv regardless of melting zone, remelting zone overlapped by next beam and HAZ. Similarly, microstructures in all weld zone consist of dendrite structure that arm spacing is $3{\sim}4{\mu}m$, matrix is ${\gamma}$(Austenite) and dendrite boundary consists of ${\gamma}$ and $M_7C_3$ of eutectic phase. This microstructure crystallizes from liquid to ${\gamma}$ of primary crystal and residual liquid forms ${\gamma}$ and $M_7C_3$ of eutectic phase by eutectic reaction at $1266^{\circ}C$. After solidification is complete, primary crystal and eutectic phase remain at room temperature without phase transformation by quenching. On the other hand, microstructures of substrate consist of ferrite, fine $M_{23}C_6$ and coarse $M_7C_3$ that have 210Hv. Microstructures in the HAZ consist of fine $M_{23}C_6$ and coarse $M_7C_3$ like substrate. But, $M_{23}C_6$ increases and matrix was changed from ferrite to bainite that has hardness above 400Hv. Partial Melted Zone is formed between melting zone and HAZ. Partial Melted Zone near the melting zone consists of ${\gamma}$, $M_7C_3$ and martensite and Partial Melted Zone near the HAZ consists of eutectic phase around ${\gamma}$ and $M_7C_3$. Hardness is maximum 557Hv in the partial melted zone.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.6 no.4
• /
• pp.153-171
• /
• 2011

The welfare system and the direction of the welfare policy have been unable to escape greatly from the frame of the past against the facts that the external environments of the national economy of the world including Korea have been changing in quick and rapid speed. Such results have caused the issues related with the welfare, economy and society ended in the ideological collision in connection with the goals of the policy, the right agreement between the policies lacked, and the intervention and conflict between the interest group concerning the policy continued. Social policy of Korea in the past had the level of complementing the parts which could not be solved through the growth. Employment creation had been achieved continuously backed up by the high rate of growth. And the low aging level, the young population structure, and the high rate of childbirth had been the structures that made such achievement possible. New economic, social and welfare environment at home and abroad has been requesting new change in welfare policy. Goal of the economic and social policy is to construct the safe economic and social system. And what has been requested has been the formation of the economic and social policy orienting the welfare nation in form of social investment and welfare expansion. Also the direction in strengthening the welfare system of Korea shall have the balance between the protection and activation strength with the necessity of converting to the prevention welfare from the post welfare. Also the public part, market, the 3rd sector and the share of the role of an individual shall be achieved. And what is needed is the achievement of the transfer from the paradigm of residual welfare to the universal welfare. And such improvements of the welfare system will be able to elevate the possible continuity of the system in long term basis through the improvement of the welfare system.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.5
• /
• pp.498-509
• /
• 2008

Reliability analyses of Level I, II and III for bearing capacity, overturning and sliding of quaywall are carried out to investigate their safety levels depending upon its failure modes, and sensitivity analyses of each design variable are performed to find their effects on safety levels of quaywall. Reliability indices was 1.416 for both level II and III for case study I, and with 2.201 and 1.880, respectively, for the case study II at the critical loading conditions. Thus we were able to know that Level II (FORM) approach is good enough to use in practical design. Generally, it was found that probabilities of failure of quaywall were higher for sliding and bearing capacity failure modes and lower for overturning failure mode. From sensitivity analyses, the most influential design variables to reliability index of quaywall were coefficient of friction, residual water pressure and resistance moment for the sliding, overturning and bearing capacity failure modes, respectively. Especially, the sensitivity of reliability index due to inertial force and dynamic water pressures, which include a large COV when earthquake occurs, did not change greatly.

• Applied Biological Chemistry
• /
• v.46 no.4
• /
• pp.305-310
• /
• 2003

Hydrophobic core variant of ubiquitin appeared to have partially folded structure at pH around 2. The intrinsic tryptophan fluorescence emission maximum of this ubiquitin variant at pH 2 showed slight blue shift compare to that of unfolded state, suggesting that some residual tertiary structures remain in this solvent condition. At the same solvent condition, this ubiquitin variant binds with hydrophobic dye, 8-anilinonaphthalene-1-sulfonic acid(AMS), which is known to bind to exposed hydrophobic surface. Furthermore, far-UV circular dichroic spectrum of this ubiquitin variant in the diminished pH was remarkably different from the far-UV CD spectrum of the native state or unfolded state. Based on the molar ellipticity at 220 nm, this ubiquitin variant at pH 2 appeared to have significant amount of secondary structures. All these observations suggest that this ubiquitin variant in the diminished solvent pH has loosely folded hydrophobic core with some secondary structures, which are key features of molten globule conformation. Since molten globule has long been considered as a protein folding intermediate, it is considered that this hydrophobic core variant ubiquitin will serve as a valuable model to study protein folding process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.535-541
• /
• 2020

FCAW is used mainly in the welding of carbon steel and alloy steel because it can be welded in all positions and can obtain excellent quality at sites with variable working conditions. Recently, many studies in Korea have estimated the fatigue strength, residual stress, and deformation, and to develop a fillet welding process. On the other hand, there have been few studies of the mechanical properties based on the strength, macro and magnetic particle test results for fillet welding. This study shows the following results through fillet welding, macro testing and strength testing using SM490A (solid-structure rolled steel) for thick plates using SS400 (rolled steel) for the upper plate and FCAW. The hardness test, macro test and magnetic particle test were then conducted. The hardness tests showed that all result values were smaller than the KS B 0893 standard values of 350Hv. The macro-test showed that each type of welded part was in a normal organic state and that there were no internal errors, bubbles, or impurities on the front of the welded part. Therefore, there were no concerns about lamination. The magnetic particle examination showed no problems.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.1
• /
• pp.81-87
• /
• 2006

The industrial systems contain many sites and components susceptible to biofilms formation. Biofilms play an important role in microbial growth and industrial fouling. Thus, the control of the biofilms in industrial systems has been emphasized, however, the efficient controlling method was not provided yet. Since silver compounds have no residual and corrosion problem, the interest for silver compounds as a biofilm control disinfectant has been increased. In this study, we attempted to examine the disinfection ability of silver compounds. The disinfection efficiency of two silver compounds(silver ion and silver oxide) were evaluated for biofilms in comparison with suspended cells using well known indicator microorganisms(E. coli, P. aeruginosa) and compared with that of chlorine. Silver compounds were found to be effective in inactivating E. coli and P. aeruginosa biofilms. The reason for superiority of silver compounds as biofilm disinfectant was suggested by that silver can penetrate into the inner biofilm matrix faster than chlorine without consumption. This study reports that the disinfectant which is highly effective in inactivating the suspended cells in water becomes the less effective for controlling biofilm because of its high reactivity. This results imply that the effective strategy for biofilm control can be achieved by considering thoroughly the chemical nature of disinfects and biofilm structure and the reactivity between them.

• The Korean Journal of Malacology
• /
• v.26 no.1
• /
• pp.51-62
• /
• 2010

The ultrastructures of germ cells and the accessory cells during spermatogenesis and mature sperm ultrastructure in male Gomphina veneriformis, which was collected on the coastal waters of Yangyang, East Sea of Korea, were investigated by transmission electron microscope observations. The morphology of the spermatozoon has a primitive type and is similar to those of other bivalves in that it contains a short midpiece with four mitochondria surrounding the centrioles. Accessory cells are observed to be connected to adjacent germ cells, they contain a large quantity of glycogen particles and lipid droplets in the cytoplasm. Therefore, it is assumed that they are involved in the supplying of the nutrients for germ cell development, while any phenomena associated with phagocytosis of undischarged, residual sperms by lysosomes in the cytoplasm of the accessory cells after spawning was not observed in this study. The morphologies of the sperm nucleus type and the acrosome shape of this species have a cylindrical and modified long cone shape, respectively. In particular, the axial filaments in the lumen of the acrosome, and subacrosomal granular materials are observed in the subacrosomal space between the anterior nuclear fossa and the beginning part of axial filaments in the acrosome. The spermatozoon is approximately $50-55{\mu}m$ in length including a long sperm nucleus (about $7.80{\mu}m$ in length), an acrosome (about $1.13{\mu}m$ in length) and tail flagellum ($40-45{\mu}m$). The axoneme of the sperm tail flagellum consists of nine pairs of microtubules at the periphery and a pair at the center. The axoneme of the sperm tail shows a 9+2 structure. Some charateristics of sperm morphology of this species in the family Veneridae are (1) acrosomal morphology, (2) the number of mitochondria in the midpiece of the sperm,. The axial filament appears in the acrosome as one of characteristics seen in several species of the family Veneridae in the subclass heterodonta, unlikely the subclass pteriomorphia containing axial rod instead of the axial filament. As some characteristics of the acrosome structures, the peripheral parts of two basal rings show electron opaque part (region), while the apex part of the acrosome shows electron lucent part (region). These charateristics belong to the family Veneridae in the subclass heterodonta, unlikely a characteristic of the subclass pteriomorphia showing all part of the acrosome being composed of electron opaque part (region). Therefore, it is easy to distinguish the families or the subclasses by the acrosome structures. The number of mitochondria in the midpiece of the sperm of this species are four, as one of common characteristics appeared in most species in the family Veneridae.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.5
• /
• pp.551-560
• /
• 2020

Recently, the offshore wind power generator market is expected to grow significantly because of increased energy demand, reduced dependence on fossil fuel-based power generation, and environmental regulations. Consequently, wind power generation is increasing worldwide, and several attempts have been made to utilize offshore wind power. Norway's Petroleum Safety Authority (PSA) requires a leg-structure design with a collision energy of 35 MJ owing to the event of a collision under operation conditions. In this study, the results of the numerical analysis of a wind turbine installation vessel subjected to ship collision were set such that the maximum collision energy that the leg could sustain was calculated and compared with the PSA requirements. The current leg design plan does not satisfy the required value of 35 MJ, and it is necessary to increase the section modulus by more than 200 % to satisfy the regulations, which is unfeasible in realistic leg design. Therefore, a collision energy standard based on a reasonable collision scenario should be established.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2215-2226
• /
• 2000

Adsorption characteristics for homologous xanthates on quartz surface has been investigated by FT-IR spectroscopy to understand the adsorption mechanism in relation with verification of the influence of surfactants on the stability of hydrophilic suspended solids in aqueous system. Contact angle measurement for water droplets on quartz surface treated with xanthate was also conducted as a supplementary study for spectroscopic investigation to grant a reliability to the interpretation of experimental results. It has been observed that monolayer of ethyl xanthate was formed on quartz surface as the adsorption progressed and double layer of ethyl xanthate was formed eventually through the reverse oriented adsorption of xanthate molecules on the monolayer. Similar trend of adsorption to the case of ethyl xanthate was found for propyl and butyl xanthates and adsorption was observed to occur more rapidly as the number of carbon atom in alkyl group of xanthate homologs increased. Thermodynamic aspect of adsorption was discussed using Young's equation and the variation in adsorption rate was examined according to the concentration of ethyl xanthate. Based on the result, it has been concluded that the adsorption features of surfactant on substrate in aquatic system is governed by molecular structure and concentration of surfactant and its residual time in aqueous environment as dissolved state also influences greatly the stability of hydrophilic suspended particles.